Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


James L. Maxwell has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Sustainable Synthesis of Diamond-like Carbon and Giant Carbon Allotropes from Hyperbaric Methanol–Water Mixtures Through the Critical Point

    by Mohamad E. Alabdulkarim, Vibhor Thapliyal, James L. Maxwell

    Freeform carbon fibres were 3D-printed from CH3OH:H2O mixtures using hyperbaric-pressure laser chemical vapour deposition (HP-LCVD). The experiment overlapped a region of known diamond growth, with the objective of depositing diamond-like carbon without the use of plasmas or hot filaments. A high-pressure regime was investigated for the first time through the precursor’s critical point. Seventy-two C-fibres were grown from 13 different CH3OH:H2O mixtures at total pressures between 7.8 and 180 bar. Maximum steady-state axial growth rates of 14 µm/s were observed. Growth near the critical point was suppressed, ostensibly due to thermal diffusion and selective etching. In addition to nanostructured graphite, various carbon allotropes were synthesised at/within the outer surface of the fibres, including diamond-like carbon, graphite polyhedral crystal, and tubular graphite cones. Several allotropes were oversized compared to structures previously reported. Raman spectral pressure–temperature (P-T) maps and a pictorial P-T phase diagram were compiled over a broad range of process conditions. Trends in the Raman ID/IG and I2D/IG intensity ratios were observed and regions of optimal growth for specific allotropes were identified. It is intended that this work provide a basis for others in optimising the growth of specific carbon allotropes from methanol using HP-LCVD and similar CVD processes.


  • Open Access

    A Comprehensive Review of High-Pressure Laser-Induced Materials Processing, Part III: Laser Reactive Synthesis within Diamond Anvil Cells

    by Mohamad Alabdulkarim, Wendy D. Maxwell, Vibhor Thapliyal, James L. Maxwell

    The synthesis of advanced materials at high pressures has been an area of growing research interest for several decades. This article is the third in a three-part series that reviews Laser Materials Processing Within Diamond Anvil Cells (L-DACs). Part III focuses on the practice of Laser Reactive Synthesis Within Diamond Anvil Cells (LRS-DAC) . During LRS-DAC processing, chemicals are precompressed within diamond anvil cells, then microscale chemical reactions are induced by focused laser beams. The method is distinguished from the well-known Laser-Heated Diamond Anvil Cell (LH-DAC) technique (see Part I) through the existence of chemical precursors (reactants), end-products, and quantifiable changes in chemical composition upon reaction. LRS-DAC processing provides at least three new degrees of freedom in the search for advanced materials (beyond adjusting static pressures and temperatures), namely: laser-excitation/cleavage of chemical bonds, time-dependent reaction kinetics via pulsed lasers, and pressure-dependent chemical kinetics. All of these broaden the synthetic phase space considerably. Through LRS-DAC experimentation, it is possible to obtain increased understanding of high-pressure chemical kinetics—and even the nature of chemical bonding itself. Here, LRS-DAC experimental methods are reviewed, along with the underlying chemistry/physics of high-pressure microchemical reactions. A chronology of key events influencing the development of LRS-DAC systems is provided, together with a summary of novel materials synthesised, and unusual chemical reactions observed. Current gaps in knowledge and emerging opportunities for further research are also suggested.


  • Open Access

    A Comprehensive Review of High-Pressure Laser-Induced Materials Processing, Part II: Laser-Driven Dynamic Compression within Diamond Anvil Cells

    by Mohamad E. Alabdulkarim, Wendy D. Maxwell, Vibhor Thapliyal, James L. Maxwell

    The field of high-pressure materials research has grown steadily over the last seven decades, with many remarkable discoveries having been made. This work is part II of a three-part series summarising recent progress in laser material processing within diamond anvil cells (L-DACs); this article focuses on the practice of laser-driven dynamic compression within diamond anvil cells (i.e., LDC–DAC experimentation). In this case, materials are initially pre-compressed within diamond anvil cells, then further dynamically compressed through the use of a high-power pulsed laser, often with the intent to isentropically compress, rather than to heat samples. The LDC–DAC approach provides a novel route to much higher dynamic pressures (approaching 1 TPa), as compared to conventional static compression within a single-stage DAC (<300 GPa) and provides a route to mapping Hugoniot curves. Recent proliferation of low-cost, high-power laser sources has led to increased research activity in LDC–DAC materials processing over the last two decades. Through LDC–DAC experiments, a greater understanding of the properties/structure of cold- and warm-dense matter has been obtained, and novel material phases have been realised. In this article, LDC–DAC experimental methods are reviewed, together with the underlying physics of laser dynamic compression in confined spaces. In addition, a chronology of important events in the development of LDC–DAC processing is provided, and emerging trends, gaps in knowledge, and suggestions for further work are considered.


  • Open Access

    A Comprehensive Review of High-Pressure Laser-Induced Materials Processing, Part I: Laser-Heated Diamond Anvil Cells

    by Mohamad E. Alabdulkarim, Wendy D. Maxwell, Vibhor Thapliyal, James L. Maxwell

    Laser-heated diamond anvil cell (LH-DAC) experimentation has emerged as a leading technique for materials processing at extreme pressures and temperatures. LH-DAC systems are often employed to better characterise the structure and properties of materials in applications ranging from condensed matter physics to geophysical research to planetary science. This article reviews LH-DAC and related laser-based characterisation, as the first part of a series within the broader context of all high-pressure laser-induced material processing. In part I of this review, a synopsis of laser-heated diamond anvil cell experimental methods, developmental history, fundamental physicochemical processes, and emerging research trends are provided. Important examples of minerals/materials modified during LH-DAC investigations (since their inception) are also tabulated, including key phase transformations, material syntheses, laser parameters, and process conditions—as a reference for the reader and as a guide for directing future research efforts. Note that laser-dynamic-compression within diamond anvil cells (LDC-DAC experimentation) and laser-induced reactive chemical synthesis within diamond anvil cells (LRS-DAC experimentation) are treated separately, as Parts II and III of this review.


  • Process–Structure Map for Diamond‐Like Carbon Fibers from Ethene at Hyperbaric Pressures

    by J. L. Maxwell, M. Boman, R. W. Springer, A. Nobile, K. DeFriend, L. Espada, M. Sandstrom, D. Kommireddy, J. Pegna, D. Goodin

    High‐pressure laser chemical vapor deposition (HP‐LCVD) is a powerful tool for growing complex microstructures at rapid rates. Not only is it possible to deposit functionally graded materials, but new metastable phases, alloys, and composite materials may be realized. In this paper, the diversity of microstructures that may be obtained through HP‐LCVD is demonstrated, including the growth of metastable materials, e.g., diamond‐like carbon (DLC). For the first time, a pressure–temperature (P–T) phase diagram has been created for HP‐LCVD, identifying nine distinct material phases of carbon from ethene. Regions of high sp3 content are identified via Raman spectroscopy. The kinetics, rate limitations, and thermodynamics of the process are also characterized at hyperbaric pressures, creating a first‐ever process‐rate map—covering the entire useful pressure range for ethene. Thermodynamically enhanced growth is also documented for the first time, where the contribution of the heat of reaction is much greater than the incident laser power—demonstrating a quasi‐self‐sustaining reaction. Finally, sufficient information is provided to reconstruct specific fiber geometries, structures, and growth rates for potential industrial production of carbon fibers from the gas phase.


  • The Benefits Divide: Health Care Purchasing In Retail Versus Other Sectors

    by James Maxwell, Peter Temin, Saminaz Zaman

    This paper is the first to compare health care purchasing in the retail versus other sectors of the Fortune 500. Employing millions of low-wage workers, the retail sector is the largest employer of uninsured workers in the economy. We found that retail companies are using the same competitive bidding process that other companies use to obtain a given level of coverage for the lowest possible cost. However, they are more price oriented than other Fortune 500 companies are. The most striking disparity lies in the nearly fivefold difference in offer rates for health care coverage. This shows that the economy’s bifurcation in health benefits extends even to the nation’s largest companies.