Jinggan Shao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jinggan Shao has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Xiao Wang
School of Materials Science and Engineering, North China University of Water Resources and Electric Power, Zhengzhou 450045, China
3 shared publications - Bing Zhang
School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450001, China
1 shared publication - Chaofeng Peng
School of Mechanical and Electronic Engineering, Zhengzhou University of Light Industry, Zhengzhou 450001, China
1 shared publication - Fei Yang
School of Intelligent Construction and Civil Engineering, Zhongyuan University of Technology, Zhengzhou 450007, China
1 shared publication - Genshang Wu
Henan College of transportation, Zhengzhou 450006, China
1 shared publication - Guoyong Ye
Henan Provincial Key Laboratory of Intelligent Manufacturing of High-End Equipment, Zhengzhou University of Light Industry, Zhengzhou 450002, China
1 shared publication
Latest Publications
- Open Access
Multi-Objective Optimization Design of Hybrid Fiber-Reinforced ECC Based on Box–Behnken and NSGA-II
To enhance the effectiveness and precision of design and to produce more low-carbon and high-performance Engineered Cementitious Composites (ECCs), novel hybrid fiber-reinforced high-ductility cementitious composites developed by incorporating a combination of ultra-high-molecular-weight polyethylene fibers (UHMWPE) and basalt fibers (BFs) into the cementitious matrix. Building upon the Box–Behnken design model from Response Surface Methodology (RSM), this study investigates the effects of different water-to-binder ratios and fiber contents on the mechanical properties of hybrid fiber-reinforced ECC. Analysis of variance (ANOVA) was used to validate the regression models. Furthermore, multi-objective optimization of the ECC mix proportion was achieved by employing the NSGA-II algorithm in conjunction with the TOPSIS comprehensive evaluation method. The results indicate that UHMWPE and BFs exhibited a significant positive hybrid effect. The order of factor significance was as follows: The content of ultra-high-molecular-weight polyethylene is greater than that of basalt fiber, and the content of basalt fiber is greater than that of the water–binder ratio. The results of variance analysis show that the regression model has high fitting accuracy. Furthermore, the algorithmic optimization yielded an optimal mix proportion: a water-to-binder ratio of 0.21, UHMWPE fiber content of 1.51%, and BF content of 0.85%. This study provides a valuable reference for the multi-objective optimization design of ECC mix proportions targeting diverse strength and toughness requirements.
Open AccessMulti-Objective Optimization Design of Hybrid Fiber-Reinforced ECC Based on Box–Behnken and NSGA-II
To enhance the effectiveness and precision of design and to produce more low-carbon and high-performance Engineered Cementitious Composites (ECCs), novel hybrid fiber-reinforced high-ductility cementitious composites developed by incorporating a combination of ultra-high-molecular-weight polyethylene fibers (UHMWPE) and basalt fibers (BFs) into the cementitious matrix. Building upon the Box–Behnken design model from Response Surface Methodology (RSM), this study investigates the effects of different water-to-binder ratios and fiber contents on the mechanical properties of hybrid fiber-reinforced ECC. Analysis of variance (ANOVA) was used to validate the regression models. Furthermore, multi-objective optimization of the ECC mix proportion was achieved by employing the NSGA-II algorithm in conjunction with the TOPSIS comprehensive evaluation method. The results indicate that UHMWPE and BFs exhibited a significant positive hybrid effect. The order of factor significance was as follows: The content of ultra-high-molecular-weight polyethylene is greater than that of basalt fiber, and the content of basalt fiber is greater than that of the water–binder ratio. The results of variance analysis show that the regression model has high fitting accuracy. Furthermore, the algorithmic optimization yielded an optimal mix proportion: a water-to-binder ratio of 0.21, UHMWPE fiber content of 1.51%, and BF content of 0.85%. This study provides a valuable reference for the multi-objective optimization design of ECC mix proportions targeting diverse strength and toughness requirements.
- Open Access
Research on Liquid Flow Pulsation Reduction in Microchannel of Pneumatic Microfluidic Chip Based on Membrane Microvalve
The unsteady and discontinuous liquid flow in the microchannel affects the efficiency of sample mixing, molecular detection, target acquisition, and biochemical reaction. In this work, an active method of reducing the flow pulsation in the microchannel of a pneumatic microfluidic chip is proposed by using an on-chip membrane microvalve as a valve chamber damping hole or a valve chamber accumulator. The structure, working principle, and multi-physical model of the reducing element of reducing the flow pulsation in a microchannel are presented. When the flow pulsation in the microchannel is sinusoidal, square wave, or pulse, the simulation effect of flow pulsation reduction is given when the membrane valve has different permutations and combinations. The experimental results show that the inlet flow of the reducing element is a square wave pulsation with an amplitude of 0.1 mL/s and a period of 2 s, the outlet flow of the reducing element is assisted by 0.017 and the fluctuation frequency is accompanied by a decrease. The test data and simulation results verify the rationality of the flow reduction element in the membrane valve microchannel, the correctness of the theoretical model, and the practicability of the specific application, which provides a higher precision automatic control technology for the microfluidic chip with high integration and complex reaction function.
Open AccessResearch on Liquid Flow Pulsation Reduction in Microchannel of Pneumatic Microfluidic Chip Based on Membrane Microvalve
The unsteady and discontinuous liquid flow in the microchannel affects the efficiency of sample mixing, molecular detection, target acquisition, and biochemical reaction. In this work, an active method of reducing the flow pulsation in the microchannel of a pneumatic microfluidic chip is proposed by using an on-chip membrane microvalve as a valve chamber damping hole or a valve chamber accumulator. The structure, working principle, and multi-physical model of the reducing element of reducing the flow pulsation in a microchannel are presented. When the flow pulsation in the microchannel is sinusoidal, square wave, or pulse, the simulation effect of flow pulsation reduction is given when the membrane valve has different permutations and combinations. The experimental results show that the inlet flow of the reducing element is a square wave pulsation with an amplitude of 0.1 mL/s and a period of 2 s, the outlet flow of the reducing element is assisted by 0.017 and the fluctuation frequency is accompanied by a decrease. The test data and simulation results verify the rationality of the flow reduction element in the membrane valve microchannel, the correctness of the theoretical model, and the practicability of the specific application, which provides a higher precision automatic control technology for the microfluidic chip with high integration and complex reaction function.
- Open Access
- 22 September 2025
- Published by MDPI AG in Micromachines
- Vol. 16 (9) , 1069
Design and Research of Superimposed Force Sensor
The measurement accuracy and equipment stability of superposition-type force sensors are primarily influenced by the layout and number of individual force sensors. Analyzing this impact effect through experimental testing for each configuration would consume significant manpower, material resources, and financial costs. To efficiently analyze the influence of the number of paralleled individual sensors and their layout within a superposition-type force measurement instrument on overall device stability and force measurement accuracy, this paper employs SolidWorks to establish models of force instruments based on common superposition schemes. Subsequently, ANSYS is utilized to perform finite element analysis on models of different schemes, obtaining corresponding data on total deformation, stress, and simulated force values. The analysis results indicate that a relatively sparse sensor layout with symmetric arrangement around the center point of the base plate enhances overall stability, and the force measurement error can be controlled within several ten-thousandths. Furthermore, the more stable and higher-accuracy schemes identified through simulation analysis were compared with practical experimental results to analyze theoretical versus actual errors. The test results showed that when the three single force sensors are placed in a “Pin font” shape, the sum of the forces measured by each individual sensor differs from the sum of the forces measured by the superimposed sensors by only a few ten-thousandths, which is within the acceptable range.
- 22 September 2025
- Published by MDPI AG in Micromachines
- Vol. 16 (9) , 1069
Open AccessDesign and Research of Superimposed Force Sensor
The measurement accuracy and equipment stability of superposition-type force sensors are primarily influenced by the layout and number of individual force sensors. Analyzing this impact effect through experimental testing for each configuration would consume significant manpower, material resources, and financial costs. To efficiently analyze the influence of the number of paralleled individual sensors and their layout within a superposition-type force measurement instrument on overall device stability and force measurement accuracy, this paper employs SolidWorks to establish models of force instruments based on common superposition schemes. Subsequently, ANSYS is utilized to perform finite element analysis on models of different schemes, obtaining corresponding data on total deformation, stress, and simulated force values. The analysis results indicate that a relatively sparse sensor layout with symmetric arrangement around the center point of the base plate enhances overall stability, and the force measurement error can be controlled within several ten-thousandths. Furthermore, the more stable and higher-accuracy schemes identified through simulation analysis were compared with practical experimental results to analyze theoretical versus actual errors. The test results showed that when the three single force sensors are placed in a “Pin font” shape, the sum of the forces measured by each individual sensor differs from the sum of the forces measured by the superimposed sensors by only a few ten-thousandths, which is within the acceptable range.
- Open Access
Performance Study of Asphalt Mixtures Reinforced with Gradated Basalt Fibers of Mixed Lengths
The length of basalt fibers affects the performance of asphalt mixtures. To explore the influence of different lengths of basalt fibers on the performance of asphalt mixtures, this study selected basalt fibers with lengths of 6 mm, 9 mm, and 12 mm to design gradations that were incorporated into asphalt mixtures to prepare specimens. High-temperature rutting tests, immersion Marshall tests, freeze-thaw splitting tests, and low-temperature splitting tests were conducted, resulting in 11 test mix designs and 12 test indicators. Then, a multi-objective grey target decision method was used to optimize the optimal combination ratio of basalt fiber lengths. The results indicate that compared to asphalt mixtures with single-length basalt fibers, incorporating well-combined basalt fibers significantly enhances the high-temperature, low-temperature, and water stability performance of asphalt mixtures. According to the grey target decision method, this study determined that a basalt fiber combination ratio of 3:4:3 for lengths of 6 mm, 9 mm, and 12 mm provides the best overall performance of asphalt mixtures. Additionally, when designing asphalt mixtures with graded basalt fibers, the inclusion of 9 mm fibers should be the primary control point. These research findings provide important guidance for the enhanced application of basalt fibers in road engineering.
Open AccessPerformance Study of Asphalt Mixtures Reinforced with Gradated Basalt Fibers of Mixed Lengths
The length of basalt fibers affects the performance of asphalt mixtures. To explore the influence of different lengths of basalt fibers on the performance of asphalt mixtures, this study selected basalt fibers with lengths of 6 mm, 9 mm, and 12 mm to design gradations that were incorporated into asphalt mixtures to prepare specimens. High-temperature rutting tests, immersion Marshall tests, freeze-thaw splitting tests, and low-temperature splitting tests were conducted, resulting in 11 test mix designs and 12 test indicators. Then, a multi-objective grey target decision method was used to optimize the optimal combination ratio of basalt fiber lengths. The results indicate that compared to asphalt mixtures with single-length basalt fibers, incorporating well-combined basalt fibers significantly enhances the high-temperature, low-temperature, and water stability performance of asphalt mixtures. According to the grey target decision method, this study determined that a basalt fiber combination ratio of 3:4:3 for lengths of 6 mm, 9 mm, and 12 mm provides the best overall performance of asphalt mixtures. Additionally, when designing asphalt mixtures with graded basalt fibers, the inclusion of 9 mm fibers should be the primary control point. These research findings provide important guidance for the enhanced application of basalt fibers in road engineering.
- Open Access
Study on Mechanical and Rheological Properties of Solid Waste-Based ECC
As one of the main raw materials of engineered cementitious composite (ECC), fly ash exerts the “ball effect” and “pozzolanic effect” in concrete, which improves the working performance of concrete and enhances the strength of the concrete matrix. Polyvinyl alcohol (PVA) fiber has been widely used in the preparation of ECC, while ground fly ash can be used to enhance the performance of ECC as a kind of high-activity admixture. In this paper, the compressive strength, flexural strength and flexural toughness of ECC prepared from different types of fly ash (raw fly ash, sorted fly ash and ground fly ash) are compared, and the rheological properties of the ECC are analyzed by studying the two parameters of yield stress and plastic viscosity. The results show that the smaller the particle size of fly ash is, the more sufficient it reacts with Ca(OH)2 produced by cement hydration, and the more it can improve the compressive strength and flexural strength of the matrix. In addition, the smaller the particle size of fly ash, the higher the yield stress and plastic viscosity of ECC; therefore, the distribution of PVA fiber in ECC is more uniform, thereby improving the flexural toughness and ductility of ECC.
Open AccessStudy on Mechanical and Rheological Properties of Solid Waste-Based ECC
As one of the main raw materials of engineered cementitious composite (ECC), fly ash exerts the “ball effect” and “pozzolanic effect” in concrete, which improves the working performance of concrete and enhances the strength of the concrete matrix. Polyvinyl alcohol (PVA) fiber has been widely used in the preparation of ECC, while ground fly ash can be used to enhance the performance of ECC as a kind of high-activity admixture. In this paper, the compressive strength, flexural strength and flexural toughness of ECC prepared from different types of fly ash (raw fly ash, sorted fly ash and ground fly ash) are compared, and the rheological properties of the ECC are analyzed by studying the two parameters of yield stress and plastic viscosity. The results show that the smaller the particle size of fly ash is, the more sufficient it reacts with Ca(OH)2 produced by cement hydration, and the more it can improve the compressive strength and flexural strength of the matrix. In addition, the smaller the particle size of fly ash, the higher the yield stress and plastic viscosity of ECC; therefore, the distribution of PVA fiber in ECC is more uniform, thereby improving the flexural toughness and ductility of ECC.
- Open Access
- 30 September 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (19) , 12517
Influence of Basalt Fiber on Mechanical Properties and Microstructure of Rubber Concrete
The utilization of waste rubber in concrete will reduce pollution and improve the efficiency of resource utilization. The effects of rubber particles and basalt fibers on the compressive strength and splitting tensile strength of concrete were investigated. In addition, the influence of basalt fibers on the mechanical properties and micropore structure of rubber concrete (RC) were analyzed using scanning electron microscopy (SEM) and X-ray computed tomography (CT). The distribution of rubber particles in concrete was also studied. The results indicate that the effects of basalts fibers on the mechanical properties of rubber concrete were significant. The rubber particles were evenly distributed in the concrete. Compared with normal concrete (NC), rubber concrete with 10% rubber particles had lower compressive strength and splitting tensile strength. Compared with rubber concrete, basalt fiber rubber concrete (BFRC) with 2% basalt fibers had no obvious effect on the compressive strength, while significantly improving the splitting tensile strength, refining the pores of rubber concrete, and reducing the porosity of the matrix. The effects of basalt fiber on the properties and pore distribution of RC should be considered in future applications.
- 30 September 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (19) , 12517
Open AccessInfluence of Basalt Fiber on Mechanical Properties and Microstructure of Rubber Concrete
The utilization of waste rubber in concrete will reduce pollution and improve the efficiency of resource utilization. The effects of rubber particles and basalt fibers on the compressive strength and splitting tensile strength of concrete were investigated. In addition, the influence of basalt fibers on the mechanical properties and micropore structure of rubber concrete (RC) were analyzed using scanning electron microscopy (SEM) and X-ray computed tomography (CT). The distribution of rubber particles in concrete was also studied. The results indicate that the effects of basalts fibers on the mechanical properties of rubber concrete were significant. The rubber particles were evenly distributed in the concrete. Compared with normal concrete (NC), rubber concrete with 10% rubber particles had lower compressive strength and splitting tensile strength. Compared with rubber concrete, basalt fiber rubber concrete (BFRC) with 2% basalt fibers had no obvious effect on the compressive strength, while significantly improving the splitting tensile strength, refining the pores of rubber concrete, and reducing the porosity of the matrix. The effects of basalt fiber on the properties and pore distribution of RC should be considered in future applications.