Hae-In Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hae-In Kim has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Jaewon Jang
Kyungpook National University
4 shared publications - Kwangeun Kim
School of Electronics and Information Engineering, Korea Aerospace University, Goyang 10540, Republic of Korea
4 shared publications - Taehun Lee
School of Electronic and Electrical Engineering, Kyungpook National University, Daegu 41566, Republic of Korea
4 shared publications - Won-Yong Lee
School of Electronic and Electrical Engineering, Kyungpook National University, Daegu 41566, Republic of Korea
4 shared publications - In Man Kang
School of Electronic and Electrical Engineering, Kyungpook National University, Daegu, Republic of Korea
3 shared publications - Jin-Hyuk Bae
Kyungpook National University
3 shared publications
Latest Publications
- Open Access
- 31 August 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (17) , 2462
Sol–Gel-Processed Y2O3–Al2O3 Mixed Oxide-Based Resistive Random-Access-Memory Devices
Herein, sol–gel-processed Y2O3–Al2O3 mixed oxide-based resistive random-access-memory (RRAM) devices with different proportions of the involved Y2O3 and Al2O3 precursors were fabricated on indium tin oxide/glass substrates. The corresponding structural, chemical, and electrical properties were investigated. The fabricated devices exhibited conventional bipolar RRAM characteristics without requiring a high-voltage forming process. With an increase in the percentage of Al2O3 precursor above 50 mol%, the crystallinity reduced, with the amorphous phase increasing owing to internal stress. Moreover, with increasing Al2O3 percentage, the lattice oxygen percentage increased and the oxygen vacancy percentage decreased. A 50% Y2O3–50% Al2O3 mixed oxide-based RRAM device exhibited the maximum high-resistance-state/low-resistance-state (HRS/LRS) ratio, as required for a large readout margin and array size. Additionally, this device demonstrated good endurance characteristics, maintaining stability for approximately 100 cycles with a high HRS/LRS ratio (>104). The HRS and LRS resistances were also retained up to 104 s without considerable degradation.
- 31 August 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (17) , 2462
Open AccessSol–Gel-Processed Y2O3–Al2O3 Mixed Oxide-Based Resistive Random-Access-Memory Devices
Herein, sol–gel-processed Y2O3–Al2O3 mixed oxide-based resistive random-access-memory (RRAM) devices with different proportions of the involved Y2O3 and Al2O3 precursors were fabricated on indium tin oxide/glass substrates. The corresponding structural, chemical, and electrical properties were investigated. The fabricated devices exhibited conventional bipolar RRAM characteristics without requiring a high-voltage forming process. With an increase in the percentage of Al2O3 precursor above 50 mol%, the crystallinity reduced, with the amorphous phase increasing owing to internal stress. Moreover, with increasing Al2O3 percentage, the lattice oxygen percentage increased and the oxygen vacancy percentage decreased. A 50% Y2O3–50% Al2O3 mixed oxide-based RRAM device exhibited the maximum high-resistance-state/low-resistance-state (HRS/LRS) ratio, as required for a large readout margin and array size. Additionally, this device demonstrated good endurance characteristics, maintaining stability for approximately 100 cycles with a high HRS/LRS ratio (>104). The HRS and LRS resistances were also retained up to 104 s without considerable degradation.
- Open Access
- 27 August 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (17) , 2432
Sol–Gel-Processed Y2O3 Multilevel Resistive Random-Access Memory Cells for Neural Networks
Yttrium oxide (Y2O3) resistive random-access memory (RRAM) devices were fabricated using the sol–gel process on indium tin oxide/glass substrates. These devices exhibited conventional bipolar RRAM characteristics without requiring a high-voltage forming process. The effect of current compliance on the Y2O3 RRAM devices was investigated, and the results revealed that the resistance values gradually decreased with increasing set current compliance values. By regulating these values, the formation of pure Ag conductive filament could be restricted. The dominant oxygen ion diffusion and migration within Y2O3 leads to the formation of oxygen vacancies and Ag metal-mixed conductive filaments between the two electrodes. The filament composition changes from pure Ag metal to Ag metal mixed with oxygen vacancies, which is crucial for realizing multilevel cell (MLC) switching. Consequently, intermediate resistance values were obtained, which were suitable for MLC switching. The fabricated Y2O3 RRAM devices could function as a MLC with a capacity of two bits in one cell, utilizing three low-resistance states and one common high-resistance state. The potential of the Y2O3 RRAM devices for neural networks was further explored through numerical simulations. Hardware neural networks based on the Y2O3 RRAM devices demonstrated effective digit image classification with a high accuracy rate of approximately 88%, comparable to the ideal software-based classification (~92%). This indicates that the proposed RRAM can be utilized as a memory component in practical neuromorphic systems.
- 27 August 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (17) , 2432
Open AccessSol–Gel-Processed Y2O3 Multilevel Resistive Random-Access Memory Cells for Neural Networks
Yttrium oxide (Y2O3) resistive random-access memory (RRAM) devices were fabricated using the sol–gel process on indium tin oxide/glass substrates. These devices exhibited conventional bipolar RRAM characteristics without requiring a high-voltage forming process. The effect of current compliance on the Y2O3 RRAM devices was investigated, and the results revealed that the resistance values gradually decreased with increasing set current compliance values. By regulating these values, the formation of pure Ag conductive filament could be restricted. The dominant oxygen ion diffusion and migration within Y2O3 leads to the formation of oxygen vacancies and Ag metal-mixed conductive filaments between the two electrodes. The filament composition changes from pure Ag metal to Ag metal mixed with oxygen vacancies, which is crucial for realizing multilevel cell (MLC) switching. Consequently, intermediate resistance values were obtained, which were suitable for MLC switching. The fabricated Y2O3 RRAM devices could function as a MLC with a capacity of two bits in one cell, utilizing three low-resistance states and one common high-resistance state. The potential of the Y2O3 RRAM devices for neural networks was further explored through numerical simulations. Hardware neural networks based on the Y2O3 RRAM devices demonstrated effective digit image classification with a high accuracy rate of approximately 88%, comparable to the ideal software-based classification (~92%). This indicates that the proposed RRAM can be utilized as a memory component in practical neuromorphic systems.
- Open Access
- 27 July 2023
- Published by MDPI AG in Preprints.org
Sol–Gel-Processed Y2O3 Multi-level Resistive Memory Cells for Neural Networks
Yttrium oxide (Y2O3) resistive random-access memory (RRAM) devices were fabricated using the sol–gel process on indium tin oxide/glass substrates. These devices exhibited conventional bipolar RRAM characteristics, without requiring a high voltage forming process. The effect of current compliance on the Y2O3 RRAM devices was investigated and revealed that as the set current compliance values increased, the resistance values gradually decreased. Consequently, intermediate resistance values were obtained, which are suitable for multi-level cell (MLC) switching. The fabricated Y2O3 RRAM devices were capable of functioning as an MLC with a capacity of 2 bits in one cell, utilizing three low resistance states and one common high resistance state. The potential of the Y2O3 RRAM for neural networks was further explored through numerical simulations. Hardware neural networks based on the Y2O3 RRAM demonstrated effective digit image classification with a high accuracy rate of approximately 88%, comparable to the ideal software-based classification (~92%). This suggests that the proposed RRAM has the potential to be utilized as a memory component in practical neuromorphic systems.
- 27 July 2023
- Published by MDPI AG in Preprints.org
Open AccessSol–Gel-Processed Y2O3 Multi-level Resistive Memory Cells for Neural Networks
Yttrium oxide (Y2O3) resistive random-access memory (RRAM) devices were fabricated using the sol–gel process on indium tin oxide/glass substrates. These devices exhibited conventional bipolar RRAM characteristics, without requiring a high voltage forming process. The effect of current compliance on the Y2O3 RRAM devices was investigated and revealed that as the set current compliance values increased, the resistance values gradually decreased. Consequently, intermediate resistance values were obtained, which are suitable for multi-level cell (MLC) switching. The fabricated Y2O3 RRAM devices were capable of functioning as an MLC with a capacity of 2 bits in one cell, utilizing three low resistance states and one common high resistance state. The potential of the Y2O3 RRAM for neural networks was further explored through numerical simulations. Hardware neural networks based on the Y2O3 RRAM demonstrated effective digit image classification with a high accuracy rate of approximately 88%, comparable to the ideal software-based classification (~92%). This suggests that the proposed RRAM has the potential to be utilized as a memory component in practical neuromorphic systems.
- Open Access
Improved Environment Stability of Y2O3 RRAM Devices with Au Passivated Ag Top Electrodes
In this study, we fabricated sol-gel-processed Y2O3-based resistive random-access memory (RRAM) devices. The fabricated Y2O3 RRAM devices exhibited conventional bipolar RRAM device characteristics and did not require the forming process. The long-term stability of the RRAM devices was investigated. The Y2O3 RRAM devices with a 20 nm thick Ag top electrode showed an increase in the low resistance state (LRS) and high resistance state (HRS) and a decrease in the HRS/LRS ratio after 30 days owing to oxidation and corrosion of the Ag electrodes. However, Y2O3 RRAM devices with inert Au-passivated Ag electrodes showed a constant RRAM device performance after 30 days. The 150 nm-thick Au passivation layer successfully suppressed the oxidation and corrosion of the Ag electrode by minimizing the chance of contact between water or oxygen molecules and Ag electrodes. The Au/Ag/Y2O3/ITO RRAM devices exhibited more than 300 switching cycles with a decent resistive window (>103). They maintained constant LRS and HRS resistances for up to 104 s, without significant degradation of nonvolatile memory properties for 30 days while stored in air.
Open AccessImproved Environment Stability of Y2O3 RRAM Devices with Au Passivated Ag Top Electrodes
In this study, we fabricated sol-gel-processed Y2O3-based resistive random-access memory (RRAM) devices. The fabricated Y2O3 RRAM devices exhibited conventional bipolar RRAM device characteristics and did not require the forming process. The long-term stability of the RRAM devices was investigated. The Y2O3 RRAM devices with a 20 nm thick Ag top electrode showed an increase in the low resistance state (LRS) and high resistance state (HRS) and a decrease in the HRS/LRS ratio after 30 days owing to oxidation and corrosion of the Ag electrodes. However, Y2O3 RRAM devices with inert Au-passivated Ag electrodes showed a constant RRAM device performance after 30 days. The 150 nm-thick Au passivation layer successfully suppressed the oxidation and corrosion of the Ag electrode by minimizing the chance of contact between water or oxygen molecules and Ag electrodes. The Au/Ag/Y2O3/ITO RRAM devices exhibited more than 300 switching cycles with a decent resistive window (>103). They maintained constant LRS and HRS resistances for up to 104 s, without significant degradation of nonvolatile memory properties for 30 days while stored in air.