Lidianne Do Nascimento Farias
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Lidianne Do Nascimento Farias has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Paulo Roberto Lopes Lima
Postgraduate Program in Civil and Environmental Engineering, State University of Feira de Santana, Feira de Santana 44036-900, BA, Brazil
5 shared publications - Romildo Dias Toledo Filho
Universidade Federal do Rio de Janeiro
4 shared publications - Adilson Brito de Arruda Filho
Center for Exact and Technological Sciences, Federal University of Recôncavo da Bahia, Cruz das Almas, Brazil
1 shared publication - Agatha Maria de Araújo Frossard Ferreira
Federal University of Rio de Janeiro (UFRJ)
1 shared publication Anfranserai Morais Dias
1 shared publication- Bruno Paolillo
University of Salerno
1 shared publication
Latest Publications
- Open Access
- 30 October 2026
- Published by Springer Nature in Materials and Structures
- Vol. 59 (9) , 434
Hybrid natural TRM systems with short flax and jute fibers for masonry strengthening: multiscale investigation of crack control and structural response
The present paper proposes the results of a multi-scale experimental campaign aimed at investigating the mechanical and structural response of Textile Reinforced Mortar (TRM) systems incorporating natural fibers and natural textile, also referred as Natural Textile Reinforced Mortar (nTRM), for existing masonry structures which can represent a promising alternative to conventional composites, combining structural effectiveness with environmental sustainability. More specifically, the natural TRM composite systems under investigation analyzed herein consider the possible combination of pre-treated flax textiles and short fibers (made of either jute or flax) employed as spread reinforcement. As a matter of principle, the application of hybrid (i.e., combination of textile and short fibers) is proposed as a possible strategy to optimize the overall amount of reinforcement by reducing the optimal number of textile layers while improving mechanical performance through the crack-bridging effect of the short fibers. The mechanical response of the proposed systems is evaluated through four-point bending tests meanwhile diagonal compression tests on reinforced masonry walls are executed to evaluate the structural response of the masonry elements. The results provide insight into the role of fiber type, fiber treatment and reinforcement configuration on strength, ductility, and crack control. The proposed approach highlights the potential of flax- and jute-based hybrid natural TRM systems as effective strengthening solutions for masonry structures, offering a material-efficient alternative to conventional synthetic reinforcement systems.
- 30 October 2026
- Published by Springer Nature in Materials and Structures
- Vol. 59 (9) , 434
Open AccessHybrid natural TRM systems with short flax and jute fibers for masonry strengthening: multiscale investigation of crack control and structural response
The present paper proposes the results of a multi-scale experimental campaign aimed at investigating the mechanical and structural response of Textile Reinforced Mortar (TRM) systems incorporating natural fibers and natural textile, also referred as Natural Textile Reinforced Mortar (nTRM), for existing masonry structures which can represent a promising alternative to conventional composites, combining structural effectiveness with environmental sustainability. More specifically, the natural TRM composite systems under investigation analyzed herein consider the possible combination of pre-treated flax textiles and short fibers (made of either jute or flax) employed as spread reinforcement. As a matter of principle, the application of hybrid (i.e., combination of textile and short fibers) is proposed as a possible strategy to optimize the overall amount of reinforcement by reducing the optimal number of textile layers while improving mechanical performance through the crack-bridging effect of the short fibers. The mechanical response of the proposed systems is evaluated through four-point bending tests meanwhile diagonal compression tests on reinforced masonry walls are executed to evaluate the structural response of the masonry elements. The results provide insight into the role of fiber type, fiber treatment and reinforcement configuration on strength, ductility, and crack control. The proposed approach highlights the potential of flax- and jute-based hybrid natural TRM systems as effective strengthening solutions for masonry structures, offering a material-efficient alternative to conventional synthetic reinforcement systems.
- Open Access
Characterization and Application of Different Types of Pineapple Leaf Fibers (PALF) in Cement-Based Composites
The use of plant fibers as reinforcement in cement composites has gained significant interest due to their favorable mechanical properties and inherent sustainability, particularly when sourced from agro-industrial waste. In this study, six types of pineapple leaf fibers from commercial and hybrid varieties were characterized in terms of morphology, crystallinity index, water absorption, dimensional stability, and mechanical properties to evaluate their potential as reinforcement in cement-based composites. An anatomical analysis of the leaves was conducted to identify fiber distribution and structural function. Cement-based composites reinforced with 1.5% (by volume) of long and aligned pineapple leaf fibers were produced and tested in bending. The results indicate that the tensile strength of pineapple fibers, ranging from 180 to 753 MPa, surpasses that of fibers already successfully used in composite reinforcement. Water absorption values ranged from 150% to 187%, while fiber diameter varied between 45% and 79% as fiber moisture changed from the dry state to the saturated state. The flexural behavior of the composites modified with pineapple leaf fibers exhibited multiple cracking and deflection hardening, with increases in flexural strength ranging from 6.25 MPa to 11 MPa. The cracking pattern under bending indicated a strong fiber–matrix bond, with values between 0.41 MPa and 0.93 MPa. All composites demonstrated high flexural toughness and great potential for the development of construction elements.
Open AccessCharacterization and Application of Different Types of Pineapple Leaf Fibers (PALF) in Cement-Based Composites
The use of plant fibers as reinforcement in cement composites has gained significant interest due to their favorable mechanical properties and inherent sustainability, particularly when sourced from agro-industrial waste. In this study, six types of pineapple leaf fibers from commercial and hybrid varieties were characterized in terms of morphology, crystallinity index, water absorption, dimensional stability, and mechanical properties to evaluate their potential as reinforcement in cement-based composites. An anatomical analysis of the leaves was conducted to identify fiber distribution and structural function. Cement-based composites reinforced with 1.5% (by volume) of long and aligned pineapple leaf fibers were produced and tested in bending. The results indicate that the tensile strength of pineapple fibers, ranging from 180 to 753 MPa, surpasses that of fibers already successfully used in composite reinforcement. Water absorption values ranged from 150% to 187%, while fiber diameter varied between 45% and 79% as fiber moisture changed from the dry state to the saturated state. The flexural behavior of the composites modified with pineapple leaf fibers exhibited multiple cracking and deflection hardening, with increases in flexural strength ranging from 6.25 MPa to 11 MPa. The cracking pattern under bending indicated a strong fiber–matrix bond, with values between 0.41 MPa and 0.93 MPa. All composites demonstrated high flexural toughness and great potential for the development of construction elements.
- 25 April 2025
- Published by Elsevier in Journal of Building Engineering
- Vol. 107
Bulk electrical resistivity of Concrete: Influence of sample size, moisture content, cracking, and composition
- 25 April 2025
- Published by Elsevier in Journal of Building Engineering
- Vol. 107
Bulk electrical resistivity of Concrete: Influence of sample size, moisture content, cracking, and composition
- Open Access
- 3 July 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (13) , 5675
Short Jute Fiber Reinforced Cement Mortar for Out-of-Plane Strengthening of Masonry Prisms
The retrofitting process contributes to the sustainability of the construction sector, since adopting measures to increase the lifespan of buildings reduces the need for new constructions. However, many of the materials used in this process come from nonrenewable sources and require significant water and energy consumption for production. The aim of this study is to assess the viability of using a more environmentally friendly mortar coating reinforced with short jute fibers (SJFRM) to reinforce ceramic brick masonry walls. Both coated and uncoated prisms were subjected to compression and flexural tests under two-point (line) out-of-plane loading. The reinforcement layer comprised mortar without fibers and mortars reinforced with jute fibers at levels of 2% and 4%, with lengths of 20 mm and 40 mm. Physical and mechanical tests were conducted to evaluate the properties of SJFRM in both fresh and hardened states. Results indicate that the compressive and flexural strengths were enhanced with SJFRM reinforcement due to alterations in the failure mode of the prisms. The fibers impede crack propagation in the reinforcement layer, enabling better redistribution of internal stresses in the prisms. This results in an increase of 6 to 9 times in stiffness under direct compression and up to 42 times in toughness under flexion in the prisms reinforced with SJFRM when compared to uncoated prisms.
- 3 July 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (13) , 5675
Open AccessShort Jute Fiber Reinforced Cement Mortar for Out-of-Plane Strengthening of Masonry Prisms
The retrofitting process contributes to the sustainability of the construction sector, since adopting measures to increase the lifespan of buildings reduces the need for new constructions. However, many of the materials used in this process come from nonrenewable sources and require significant water and energy consumption for production. The aim of this study is to assess the viability of using a more environmentally friendly mortar coating reinforced with short jute fibers (SJFRM) to reinforce ceramic brick masonry walls. Both coated and uncoated prisms were subjected to compression and flexural tests under two-point (line) out-of-plane loading. The reinforcement layer comprised mortar without fibers and mortars reinforced with jute fibers at levels of 2% and 4%, with lengths of 20 mm and 40 mm. Physical and mechanical tests were conducted to evaluate the properties of SJFRM in both fresh and hardened states. Results indicate that the compressive and flexural strengths were enhanced with SJFRM reinforcement due to alterations in the failure mode of the prisms. The fibers impede crack propagation in the reinforcement layer, enabling better redistribution of internal stresses in the prisms. This results in an increase of 6 to 9 times in stiffness under direct compression and up to 42 times in toughness under flexion in the prisms reinforced with SJFRM when compared to uncoated prisms.
- Open Access
- 23 May 2024
- Published by Editorial CSIC in Materiales de Construcción
- Vol. 74 (354) , e347
Shear behavior of hollow clay brick masonry wallet coated with short jute fiber reinforced mortar
The objective of this study is to present a new method of reinforcing masonry using layers of mortar reinforced with short jute fibers. Mortars were produced with 0%, 2% and 3% jute fibers with cementitious matrices free of calcium hydroxide. The effectiveness of the reinforced mortar was evaluated through diagonal compression tests of hollow ceramic brick masonry prisms. The prisms were coated on both sides. The experimental results demonstrated that the diagonal resistance of the fiber system increased by 28 to 30% and presented greater resistance to elastic deformation during load application, with deformation coefficients 2 and 3 times greater for 2% and 3% of fibers, respectively. Therefore, jute fibers prove to be a sustainable and efficient alternative for masonry reinforcement applications, with maximum applied loads considerably higher than the unreinforced system, in addition to better crack control.
- 23 May 2024
- Published by Editorial CSIC in Materiales de Construcción
- Vol. 74 (354) , e347
Open AccessShear behavior of hollow clay brick masonry wallet coated with short jute fiber reinforced mortar
The objective of this study is to present a new method of reinforcing masonry using layers of mortar reinforced with short jute fibers. Mortars were produced with 0%, 2% and 3% jute fibers with cementitious matrices free of calcium hydroxide. The effectiveness of the reinforced mortar was evaluated through diagonal compression tests of hollow ceramic brick masonry prisms. The prisms were coated on both sides. The experimental results demonstrated that the diagonal resistance of the fiber system increased by 28 to 30% and presented greater resistance to elastic deformation during load application, with deformation coefficients 2 and 3 times greater for 2% and 3% of fibers, respectively. Therefore, jute fibers prove to be a sustainable and efficient alternative for masonry reinforcement applications, with maximum applied loads considerably higher than the unreinforced system, in addition to better crack control.
- Open Access
- 30 April 2022
- Published by Universidade Federal de Mato Grosso in E&S Engineering and Science
- Vol. 11 (1) , 1-21
Fluência de concreto com agregados reciclados: uma revisão
A fluência é uma das propriedades mais importantes do concreto, mas o uso de Agregados Reciclados de Concreto (ARC) pode afetar significativamente essa propriedade. Neste sentido, o objetivo do presente artigo foi realizar uma revisão da literatura sobre a fluência no concreto com ARC, considerando sua influência, causas e medidas de redução. A metodologia consistiu em uma Revisão Sistemática da Literatura (RSL) para o período de tempo de 2007 até 2021 (primeiro trimestre). Foram utilizadas diferentes bases de dados de busca de informação científica, limitando-se a artigos de revista e em língua inglesa. Os resultados mostram que o Agregado Graúdo Reciclado de Concreto (AGRC) é o mais utilizado nos estudos selecionados, aumentado a fluência com o grau de substituição do agregado natural; no entanto, não há uma tendência clara com Agregado Fino Reciclado de Concreto (AFRC), cujos resultados são limitados na literatura. Apresenta-se que a fluência depende de vários fatores como a relação a/c, idade da carga, etc. Entre a principais causas, a maioria dos estudos afirma que a fluência se deve à argamassa antiga aderida ao ARC, mas também algumas medidas são propostas para reduzir a fluência no concreto com ARC. Pode-se concluir que o uso de ARC é uma alternativa sustentável para a produção de concreto, mas são necessárias mais pesquisas para entender completamente a influência do ARC na fluência do concreto e consolidar seu uso para níveis industriais.
- 30 April 2022
- Published by Universidade Federal de Mato Grosso in E&S Engineering and Science
- Vol. 11 (1) , 1-21
Open AccessFluência de concreto com agregados reciclados: uma revisão
A fluência é uma das propriedades mais importantes do concreto, mas o uso de Agregados Reciclados de Concreto (ARC) pode afetar significativamente essa propriedade. Neste sentido, o objetivo do presente artigo foi realizar uma revisão da literatura sobre a fluência no concreto com ARC, considerando sua influência, causas e medidas de redução. A metodologia consistiu em uma Revisão Sistemática da Literatura (RSL) para o período de tempo de 2007 até 2021 (primeiro trimestre). Foram utilizadas diferentes bases de dados de busca de informação científica, limitando-se a artigos de revista e em língua inglesa. Os resultados mostram que o Agregado Graúdo Reciclado de Concreto (AGRC) é o mais utilizado nos estudos selecionados, aumentado a fluência com o grau de substituição do agregado natural; no entanto, não há uma tendência clara com Agregado Fino Reciclado de Concreto (AFRC), cujos resultados são limitados na literatura. Apresenta-se que a fluência depende de vários fatores como a relação a/c, idade da carga, etc. Entre a principais causas, a maioria dos estudos afirma que a fluência se deve à argamassa antiga aderida ao ARC, mas também algumas medidas são propostas para reduzir a fluência no concreto com ARC. Pode-se concluir que o uso de ARC é uma alternativa sustentável para a produção de concreto, mas são necessárias mais pesquisas para entender completamente a influência do ARC na fluência do concreto e consolidar seu uso para níveis industriais.