Bashir Y. Al-Zaidi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Bashir Y. Al-Zaidi has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Ali Al-Shathr
Department of Chemical Engineering, University of Technology-Iraq, Baghdad 10066, Iraq
7 shared publications - Zaidoon Mohsin Shakor
Department of Chemical Engineering, University of Technology-Iraq, Baghdad, Iraq
6 shared publications - Riyadh Sadiq Al-Mukhtar
Chemical Engineering, University of Technology-Iraq, Baghdad -Iraq
3 shared publications - Alhumam A. Al-Shammari
Department of Chemical Process Engineering, College of Chemical Engineering, University of Technology-Iraq, Baghdad 10066, Iraq
2 shared publications - Murtadha S. Al-Eissa
Department of Chemical Engineering, University of Technology-Iraq, Alsinaa Street 52, Baghdad 10066, Iraq
2 shared publications - Samaa H. Al-Sultani
Department of Chemical Engineering, University of Technology-Iraq, Baghdad 10066, Iraq
2 shared publications
Latest Publications
- 1 April 2026
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 66 (4) , 377-395
Oxidative Desulfurization of Lighter Petroleum Fractions Using Supported Heteropoly-Acid Catalysts (A Review)
- 1 April 2026
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 66 (4) , 377-395
Oxidative Desulfurization of Lighter Petroleum Fractions Using Supported Heteropoly-Acid Catalysts (A Review)
- Open Access
Dual Roles of Coke in Fresh and Modified HY Zeolite Catalyzed Aromatic Alkylation: Mechanisms, Structural Transformations, and Catalyst Regeneration
Linear alkylbenzene (LAB) is the main raw material used to make biodegradable detergents, and its production process is based on aromatic alkylation. HY zeolites that have undergone controlled dealumination and desilication have led industrial standards amongst solid acid catalysts because of their controllable acidity and hierarchical pore structure. Coke formation in such systems can assume a dual role, which is dependent on its condition. Though the over-deposition is known to cause deactivation by blocking the micropores, Bronsted acid-site masking, and diffusion collapse, the low-level deposition could also be done to increase the monoalkylate selectivity by the pore mouth catalysis, steric modulation, and selective suppression of secondary alkylation pathways. The critical review is done on the structural-kinetic interaction that determines the coke evolution in HY-based catalysts. In order to moderate the acid-site density and enhance hydrothermal stability, dealumination (Si/Al optimization of about 2.5 to 30–100) occurs, but to reduce deep-pore coke formation, desilication (interconnected mesopores) is created. The bimodal porosity and regulated acidity are found to be synergistic, as hierarchical HY zeolites produced through successive cycles of steam and alkaline treatments not only show LAB selectivity in excess of 90% but also exhibit much longer catalyst lifetimes. Quantitative research on the beneficial coke regime revealed that it was composed of about 36 wt% hydrogen-rich species, which were localized at the pore mouths, hence enhancing monoalkylation selectivity by 15–40%. Beyond a critical transition window (e.g., 8–12 wt.%), coke formation to condensed polyaromatic and graphitic products leads to fast deactivated coke formation, which is due to percolation limits and transport-controlled kinetics. More advanced techniques of characterization of the coke, e.g., temperature-programmed oxidation (TPO), 27Al MAAS NMR, and UV-Raman spectroscopy, indicate how the coke is changed to highly structured graphitic deposits of high oxidation activation energy. Activity recovery of 85–98% is obtained in regeneration processes, including controlled oxidative calcination, microwave-based and plasma-based processes, and thermal management protocols, and it would be determined by the chemistry of the coke, its spatial distribution, and the regeneration protocols. This paper has developed a mechanistic coke control system by cross-tuning the acidity and development of an effective pore network, which led to a sustainable aromatic alkylation reaction with minimal activity loss, high selectivity, and long life.
Open AccessDual Roles of Coke in Fresh and Modified HY Zeolite Catalyzed Aromatic Alkylation: Mechanisms, Structural Transformations, and Catalyst Regeneration
Linear alkylbenzene (LAB) is the main raw material used to make biodegradable detergents, and its production process is based on aromatic alkylation. HY zeolites that have undergone controlled dealumination and desilication have led industrial standards amongst solid acid catalysts because of their controllable acidity and hierarchical pore structure. Coke formation in such systems can assume a dual role, which is dependent on its condition. Though the over-deposition is known to cause deactivation by blocking the micropores, Bronsted acid-site masking, and diffusion collapse, the low-level deposition could also be done to increase the monoalkylate selectivity by the pore mouth catalysis, steric modulation, and selective suppression of secondary alkylation pathways. The critical review is done on the structural-kinetic interaction that determines the coke evolution in HY-based catalysts. In order to moderate the acid-site density and enhance hydrothermal stability, dealumination (Si/Al optimization of about 2.5 to 30–100) occurs, but to reduce deep-pore coke formation, desilication (interconnected mesopores) is created. The bimodal porosity and regulated acidity are found to be synergistic, as hierarchical HY zeolites produced through successive cycles of steam and alkaline treatments not only show LAB selectivity in excess of 90% but also exhibit much longer catalyst lifetimes. Quantitative research on the beneficial coke regime revealed that it was composed of about 36 wt% hydrogen-rich species, which were localized at the pore mouths, hence enhancing monoalkylation selectivity by 15–40%. Beyond a critical transition window (e.g., 8–12 wt.%), coke formation to condensed polyaromatic and graphitic products leads to fast deactivated coke formation, which is due to percolation limits and transport-controlled kinetics. More advanced techniques of characterization of the coke, e.g., temperature-programmed oxidation (TPO), 27Al MAAS NMR, and UV-Raman spectroscopy, indicate how the coke is changed to highly structured graphitic deposits of high oxidation activation energy. Activity recovery of 85–98% is obtained in regeneration processes, including controlled oxidative calcination, microwave-based and plasma-based processes, and thermal management protocols, and it would be determined by the chemistry of the coke, its spatial distribution, and the regeneration protocols. This paper has developed a mechanistic coke control system by cross-tuning the acidity and development of an effective pore network, which led to a sustainable aromatic alkylation reaction with minimal activity loss, high selectivity, and long life.
- Open Access
- 10 February 2026
- Published by XLESCIENCE in International Journal of Advances in Signal and Image Sciences
- Vol. 12 (2s) , 423-451
Hierarchical Mesoporosity Surpasses Acidity Reduction For Mitigating Coke Deactivation: Comparative Study Of Desilicated And Dealuminated HY Zeolites In Aromatic Alkylation
Liquid-phase aromatic alkylation over HY zeolites offers an efficient route to alkylated aromatics. Secondary oligomerization and polyalkylation during reaction generate heavy hydrocarbon species that accumulate as coke within the pore network and on Brønsted acid sites, reduce site accessibility, and shorten time-on-stream stability. Post-synthesis modification that tunes acidity or introduces hierarchical porosity remains necessary to lessen deactivation and improve catalytic durability. The study examines freshly prepared HY alongside dealuminated and desilicated HY in liquid-phase alkylation of toluene with 1-octene, with a focus on catalytic activity, stability, and coke deposition behavior. Hydrothermal synthesis of Na-Y was used to prepare the parent HY zeolite, which was then subjected to double ammonium ion exchange and activated by heating. Desilicated HY showed enhanced crystallinity and a high specific surface area (700.5 m² g-¹) and maintained the total pore volume (0.344 cm³ g-¹), with the microporous FAU framework largely intact. Dealuminated HY, in contrast, exhibited partial framework degradation, a decreased surface area (538.8 m² g-¹), and a higher Si/Al ratio of 5.3. Optimized testing in a batch reactor (toluene:1-octene molar ratio of 10:1, 110 °C, and 350 mg catalyst) showed that desilicated HY achieved the highest 1-octene conversion (92%) and maintained high stability over 300 min on stream. Post-reaction TGA and CHNS results indicated that desilicated HY contained the lowest coke content (6.83 wt.%), a decrease of about 54% compared with fresh HY (12.62 wt.%). Enhanced diffusion of bulky intermediates through hierarchical mesopores inhibited secondary polymerization and reduced the formation of hard coke. The findings indicate that controlled desilication is more effective in reducing catalyst deactivation in alkylation reactions involving bulky intermediates than acidity reduction through dealumination.
- 10 February 2026
- Published by XLESCIENCE in International Journal of Advances in Signal and Image Sciences
- Vol. 12 (2s) , 423-451
Open AccessHierarchical Mesoporosity Surpasses Acidity Reduction For Mitigating Coke Deactivation: Comparative Study Of Desilicated And Dealuminated HY Zeolites In Aromatic Alkylation
Liquid-phase aromatic alkylation over HY zeolites offers an efficient route to alkylated aromatics. Secondary oligomerization and polyalkylation during reaction generate heavy hydrocarbon species that accumulate as coke within the pore network and on Brønsted acid sites, reduce site accessibility, and shorten time-on-stream stability. Post-synthesis modification that tunes acidity or introduces hierarchical porosity remains necessary to lessen deactivation and improve catalytic durability. The study examines freshly prepared HY alongside dealuminated and desilicated HY in liquid-phase alkylation of toluene with 1-octene, with a focus on catalytic activity, stability, and coke deposition behavior. Hydrothermal synthesis of Na-Y was used to prepare the parent HY zeolite, which was then subjected to double ammonium ion exchange and activated by heating. Desilicated HY showed enhanced crystallinity and a high specific surface area (700.5 m² g-¹) and maintained the total pore volume (0.344 cm³ g-¹), with the microporous FAU framework largely intact. Dealuminated HY, in contrast, exhibited partial framework degradation, a decreased surface area (538.8 m² g-¹), and a higher Si/Al ratio of 5.3. Optimized testing in a batch reactor (toluene:1-octene molar ratio of 10:1, 110 °C, and 350 mg catalyst) showed that desilicated HY achieved the highest 1-octene conversion (92%) and maintained high stability over 300 min on stream. Post-reaction TGA and CHNS results indicated that desilicated HY contained the lowest coke content (6.83 wt.%), a decrease of about 54% compared with fresh HY (12.62 wt.%). Enhanced diffusion of bulky intermediates through hierarchical mesopores inhibited secondary polymerization and reduced the formation of hard coke. The findings indicate that controlled desilication is more effective in reducing catalyst deactivation in alkylation reactions involving bulky intermediates than acidity reduction through dealumination.
- Open Access
Toluene Alkylation Reactions over Y-Type Zeolite Catalysts: An Experimental and Kinetic Study
The present study demonstrated an improvement in both 1-heptene conversion and mono-heptyltoluene selectivity. It simultaneously depicted the isomerization reactions of 1-heptene and toluene alkylation over Y zeolite catalysts having a Si/Al of 3.5 and a surface area of 817 m2/g. The physical properties of the fresh zeolite catalyst were characterized using XRD, FTIR, XRF, TPD, and N2 adsorption–desorption spectroscopy. The experimental part was carried out in a 100 mL glass flask connected to a reflux condenser at different reaction temperatures ranging from 70 to 90 °C, toluene:1-heptene ratios of 3–8, and catalyst weights of 0.25–0.4 g. The highest conversion of ~96% was obtained at the highest toluene:1-heptene ratio (i.e., 8:1), 0.25 g of zeolite Y, at 180 min of reaction time and under a reaction temperature of 90 °C. However, the selectivity of 2-heptyltoluene reached its highest value of ~25% under these conditions. Likewise, the kinetic modeling developed in this study helped describe the proposed reaction mechanism by linking the experimental results with the predicted results. The kinetic parameters were determined by nonlinear regression analysis using the MATLAB® package genetic algorithm. The ordinary differential equations were integrated with respect to time using the fourth-order Runge–Kutta method, and the resulting mole fractions were fitted against the experimental data. The mean relative error (MRE) values were calculated from the experimental and predicted results, which showed a reasonable agreement with the average MRE being ~11.7%. The calculated activation energies showed that the reaction rate follows the following order: coking (55.9–362.7 kJ/mol) > alkylation (73.1–332.1 kJ/mol) > isomerization (69.3–120.2 kJ/mol), indicating that isomerization reactions are the fastest compared to other reactions. A residual activity deactivation model was developed to measure the deactivation kinetic parameters, and the deactivation energy value obtained was about 48.2 kJ/mol.
Open AccessToluene Alkylation Reactions over Y-Type Zeolite Catalysts: An Experimental and Kinetic Study
The present study demonstrated an improvement in both 1-heptene conversion and mono-heptyltoluene selectivity. It simultaneously depicted the isomerization reactions of 1-heptene and toluene alkylation over Y zeolite catalysts having a Si/Al of 3.5 and a surface area of 817 m2/g. The physical properties of the fresh zeolite catalyst were characterized using XRD, FTIR, XRF, TPD, and N2 adsorption–desorption spectroscopy. The experimental part was carried out in a 100 mL glass flask connected to a reflux condenser at different reaction temperatures ranging from 70 to 90 °C, toluene:1-heptene ratios of 3–8, and catalyst weights of 0.25–0.4 g. The highest conversion of ~96% was obtained at the highest toluene:1-heptene ratio (i.e., 8:1), 0.25 g of zeolite Y, at 180 min of reaction time and under a reaction temperature of 90 °C. However, the selectivity of 2-heptyltoluene reached its highest value of ~25% under these conditions. Likewise, the kinetic modeling developed in this study helped describe the proposed reaction mechanism by linking the experimental results with the predicted results. The kinetic parameters were determined by nonlinear regression analysis using the MATLAB® package genetic algorithm. The ordinary differential equations were integrated with respect to time using the fourth-order Runge–Kutta method, and the resulting mole fractions were fitted against the experimental data. The mean relative error (MRE) values were calculated from the experimental and predicted results, which showed a reasonable agreement with the average MRE being ~11.7%. The calculated activation energies showed that the reaction rate follows the following order: coking (55.9–362.7 kJ/mol) > alkylation (73.1–332.1 kJ/mol) > isomerization (69.3–120.2 kJ/mol), indicating that isomerization reactions are the fastest compared to other reactions. A residual activity deactivation model was developed to measure the deactivation kinetic parameters, and the deactivation energy value obtained was about 48.2 kJ/mol.
- Open Access
- 1 December 2024
- Published by University of Technology, Iraq - DIGITAL COMMONS in Journal of Applied Sciences and Nanotechnology
- Vol. 4 (4) , 29-46
Coke Decomposition Kinetic Model of Spent Hydrodesulfurization Catalysts
Recycling residue hydrodesulfurization (HDS) catalysts is essential due to frequent deactivation. Petroleum coke's high ignition temperature and complex combustion behavior stem from its graphite-like structure and low volatile matter. This study investigates petroleum coke combustion and oxidation kinetics with metal catalysts. Data from HDS catalysts (5% Co-10% Mo/active kaolin and 5% Co-10% Mo/active bentonite) are crucial for industrial regenerator simulations. Iraqi mineral clays, treated and loaded with cobalt and molybdenum, were used in HDS reactions of Iraqi gas oil with 10200 ppm sulfur at 360°C, 12 bar, and WHSV of 2 h⁻¹. Spent catalysts, coated with coke, were analyzed, and coke was removed using thermogravimetric analysis (TGA) at heating rates of 2.5, 5, and 10°C/min. MATLAB software assessed coke accumulation's impact on combustion activation energy via model-free and model-based methods. Activation energies for coke combustion were 46.48, 87.71, and 102.68 kJ/mol for hydrocarbons, soft coke, and hard coke, respectively, on 5% Co-10% Mo/active kaolin, and 41.98, 68.11, and 100.38 kJ/mol for 5% Co-10% Mo/active bentonite. TGA revealed 7.553% and 7.977% total weight loss in kaolin and bentonite catalysts. The model-based method was most effective for regenerating aged HDS catalysts at 850°C, especially for hard coke removal. DTG analysis showed two concavities, indicating soft coke below 350°C and hard coke between 350 and 850°C. For 5%Co-10%Mo/kaolin catalysts, peak temperatures (Tpeak) were 517, 526, and 610°C at heating rates of 2.5, 5, and 10°C/min. Bentonite catalysts showed lower Tpeak values.
- 1 December 2024
- Published by University of Technology, Iraq - DIGITAL COMMONS in Journal of Applied Sciences and Nanotechnology
- Vol. 4 (4) , 29-46
Open AccessCoke Decomposition Kinetic Model of Spent Hydrodesulfurization Catalysts
Recycling residue hydrodesulfurization (HDS) catalysts is essential due to frequent deactivation. Petroleum coke's high ignition temperature and complex combustion behavior stem from its graphite-like structure and low volatile matter. This study investigates petroleum coke combustion and oxidation kinetics with metal catalysts. Data from HDS catalysts (5% Co-10% Mo/active kaolin and 5% Co-10% Mo/active bentonite) are crucial for industrial regenerator simulations. Iraqi mineral clays, treated and loaded with cobalt and molybdenum, were used in HDS reactions of Iraqi gas oil with 10200 ppm sulfur at 360°C, 12 bar, and WHSV of 2 h⁻¹. Spent catalysts, coated with coke, were analyzed, and coke was removed using thermogravimetric analysis (TGA) at heating rates of 2.5, 5, and 10°C/min. MATLAB software assessed coke accumulation's impact on combustion activation energy via model-free and model-based methods. Activation energies for coke combustion were 46.48, 87.71, and 102.68 kJ/mol for hydrocarbons, soft coke, and hard coke, respectively, on 5% Co-10% Mo/active kaolin, and 41.98, 68.11, and 100.38 kJ/mol for 5% Co-10% Mo/active bentonite. TGA revealed 7.553% and 7.977% total weight loss in kaolin and bentonite catalysts. The model-based method was most effective for regenerating aged HDS catalysts at 850°C, especially for hard coke removal. DTG analysis showed two concavities, indicating soft coke below 350°C and hard coke between 350 and 850°C. For 5%Co-10%Mo/kaolin catalysts, peak temperatures (Tpeak) were 517, 526, and 610°C at heating rates of 2.5, 5, and 10°C/min. Bentonite catalysts showed lower Tpeak values.
- Open Access
Aromatics Alkylated with Olefins Utilizing Zeolites as Heterogeneous Catalysts: A Review
The alkylation reaction of aromatic compounds gains considerable attention because of its wide application in bulk and fine chemical production. Aromatics alkylated with olefins is a well-known process, particularly for linear alkylbenzene, phenyloctanes, and heptyltoluene production. As octane boosters and precursors for various petrochemical and bulk chemical products, a wide range of alkylated compounds are in high demand. Numerous unique structures have been proposed in addition to the usual zeolites (Y and beta) utilized in alkylation procedures. The inevitable deactivation of industrial catalysts over time on stream, which is followed by a decrease in catalytic activity and product selectivity, is one of their disadvantages. Therefore, careful consideration of catalyst deactivation regarding the setup and functioning of the process of catalysis is necessary. Although a lot of work has been carried out to date to prevent coke and increase catalyst lifespan, deactivation of the catalyst is still unavoidable. Coke deposition can lead to catalyst deactivation in industrial catalytic processes by obstructing pores and/or covering acid sites. It is very desirable to regenerate inactive catalysts in order to remove the coke and restore catalytic activity at the same time. Depending on the kind of catalyst, the deactivation processes, and the regeneration settings, each regeneration approach has pros and cons. In this comprehensive study, the focus was on discussing the reaction mechanism of 1-octene isomerization and toluene alkylation as an example of isomerization and alkylation reactions that occur simultaneously, shedding light in detail on the catalysts used for this type of complex reaction, taking into account the challenges facing the catalyst deactivation and reactivation procedures.
Open AccessAromatics Alkylated with Olefins Utilizing Zeolites as Heterogeneous Catalysts: A Review
The alkylation reaction of aromatic compounds gains considerable attention because of its wide application in bulk and fine chemical production. Aromatics alkylated with olefins is a well-known process, particularly for linear alkylbenzene, phenyloctanes, and heptyltoluene production. As octane boosters and precursors for various petrochemical and bulk chemical products, a wide range of alkylated compounds are in high demand. Numerous unique structures have been proposed in addition to the usual zeolites (Y and beta) utilized in alkylation procedures. The inevitable deactivation of industrial catalysts over time on stream, which is followed by a decrease in catalytic activity and product selectivity, is one of their disadvantages. Therefore, careful consideration of catalyst deactivation regarding the setup and functioning of the process of catalysis is necessary. Although a lot of work has been carried out to date to prevent coke and increase catalyst lifespan, deactivation of the catalyst is still unavoidable. Coke deposition can lead to catalyst deactivation in industrial catalytic processes by obstructing pores and/or covering acid sites. It is very desirable to regenerate inactive catalysts in order to remove the coke and restore catalytic activity at the same time. Depending on the kind of catalyst, the deactivation processes, and the regeneration settings, each regeneration approach has pros and cons. In this comprehensive study, the focus was on discussing the reaction mechanism of 1-octene isomerization and toluene alkylation as an example of isomerization and alkylation reactions that occur simultaneously, shedding light in detail on the catalysts used for this type of complex reaction, taking into account the challenges facing the catalyst deactivation and reactivation procedures.
- Open Access
- 1 December 2023
- Published by MDPI AG in Chemengineering
- Vol. 7 (6) , 115
Experimental and Kinetic Study of the Catalytic Behavior of Sulfate-Treated Nanostructured Bifunctional Zirconium Oxide Catalysts in n-Heptane Hydroisomerization Reactions
In this study, a mono-functional ZrO2 nanomaterial was treated with sulfur and loaded with two different percentages of platinum metals (i.e., 0.5 and 1 wt%) to generate an acidic bi-functional Pt/SZrO2 nanocatalyst for the purpose of increasing the catalytic activity and selectivity together. This work aims to determine the least amount of the costly platinum metal that can be added to the catalyst to achieve the appropriate balance between the acidic and metallic sites. Both rapid deactivation of the super-acid nanaocatalyst and fast cleavage of the zero-octane n-heptane chain can consequently be prevented throughout the reaction. This can be achieved by accelerating the hydroisomerization reactions at a pressure of 5 bar to reach the highest selectivity towards producing the desired multi-branched compound in fuel. Several characterization techniques, including XRD, SEM, EDX, BET, and FTIR, have been used to evaluate the physical properties of the catalysts. The best reaction product was obtained at 230 °C compared to the other tested temperatures. The conversion, selectivity, and yield of reaction products over the surfaces of the prepared catalysts followed this order: 0.5 wt% Pt/SZrO2 > 1 wt% Pt/SZrO2 > 0.5 wt% Pt/ZrO2 > 1 wt% Pt/ZrO2 > SZrO2 > ZrO2. The highest conversion, selectivity, and yield values were obtained on the surface of the 0.5 wt% Pt/SZrO2 catalyst, which are 69.64, 81.4 and 56.68 wt%, respectively, while the lowest values were obtained on the surface of the parent ZrO2 catalyst, which are 43.9, 61.1 and 26.82, respectively. The kinetic model and apparent activation energies were also implemented for each of the hydroisomerization, hydrogenation/dehydrogenation, and hydrocracking reactions, which track the following order: hydroisomerization < hydrogenation/dehydrogenation < hydrocracking. The lowest apparent activation energy value of 123.39 kJ/mol was found on the surface of the most active and selective 0.5% Pt/SZrO2 nanocatalyst.
- 1 December 2023
- Published by MDPI AG in Chemengineering
- Vol. 7 (6) , 115
Open AccessExperimental and Kinetic Study of the Catalytic Behavior of Sulfate-Treated Nanostructured Bifunctional Zirconium Oxide Catalysts in n-Heptane Hydroisomerization Reactions
In this study, a mono-functional ZrO2 nanomaterial was treated with sulfur and loaded with two different percentages of platinum metals (i.e., 0.5 and 1 wt%) to generate an acidic bi-functional Pt/SZrO2 nanocatalyst for the purpose of increasing the catalytic activity and selectivity together. This work aims to determine the least amount of the costly platinum metal that can be added to the catalyst to achieve the appropriate balance between the acidic and metallic sites. Both rapid deactivation of the super-acid nanaocatalyst and fast cleavage of the zero-octane n-heptane chain can consequently be prevented throughout the reaction. This can be achieved by accelerating the hydroisomerization reactions at a pressure of 5 bar to reach the highest selectivity towards producing the desired multi-branched compound in fuel. Several characterization techniques, including XRD, SEM, EDX, BET, and FTIR, have been used to evaluate the physical properties of the catalysts. The best reaction product was obtained at 230 °C compared to the other tested temperatures. The conversion, selectivity, and yield of reaction products over the surfaces of the prepared catalysts followed this order: 0.5 wt% Pt/SZrO2 > 1 wt% Pt/SZrO2 > 0.5 wt% Pt/ZrO2 > 1 wt% Pt/ZrO2 > SZrO2 > ZrO2. The highest conversion, selectivity, and yield values were obtained on the surface of the 0.5 wt% Pt/SZrO2 catalyst, which are 69.64, 81.4 and 56.68 wt%, respectively, while the lowest values were obtained on the surface of the parent ZrO2 catalyst, which are 43.9, 61.1 and 26.82, respectively. The kinetic model and apparent activation energies were also implemented for each of the hydroisomerization, hydrogenation/dehydrogenation, and hydrocracking reactions, which track the following order: hydroisomerization < hydrogenation/dehydrogenation < hydrocracking. The lowest apparent activation energy value of 123.39 kJ/mol was found on the surface of the most active and selective 0.5% Pt/SZrO2 nanocatalyst.
- Open Access
Hydroisomerisation and Hydrocracking of n-Heptane: Modelling and Optimisation Using a Hybrid Artificial Neural Network–Genetic Algorithm (ANN–GA)
In this paper, the focus is on upgrading the value of naphtha compounds represented by n-heptane (n-C7H16) with zero octane number using a commercial zeolite catalyst consisting of a mixture of 75% HY and 25% HZSM-5 loaded with different amounts, 0.25 to 1 wt.%, of platinum metal. Hydrocracking and hydroisomerisation processes are experimentally and theoretically studied in the temperature range of 300–400 °C and under various contact times. A feedforward artificial neural network (FFANN) based on two hidden layers was used for the purpose of process modelling. A total of 80% of the experimental results was used to train the artificial neural network, with the remaining results being used for evaluation and testing of the network. Tan-sigmoid and log-sigmoid transfer functions were used in the first and second hidden layers, respectively. The optimum number of neurons in hidden layers was determined depending on minimising the mean absolute error (MAE). The best ANN model, represented by the multilayer FFANN, had a 4–24–24–12 topology. The ANN model accurately simulates the process in which the correlation coefficient (R2) was found to be 0.9918, 0.9492, and 0.9426 for training, validation, and testing, respectively, and an average of 0.9767 for all data. In addition, the operating conditions of the process were optimised using the genetic algorithm (GA) towards increasing the octane number of the products. MATLAB® Version 2020a was utilised to complete all required computations and predictions. Optimal operating conditions were found through the theoretical study: 0.85 wt.% Pt-metal loaded, 359.36 °C, 6.562 H2/n-heptane feed ratio, and 3.409 h−1 weight-hourly space velocity (WHSV), through which the maximum octane number (RON) of 106.84 was obtained. Finally, those operating conditions largely matched what was calculated from the results of the experimental study, where the highest percentage of the resulting isomers was found with about 78.7 mol% on the surface of the catalyst loaded with 0.75 wt.% Pt-metal at 350 °C using a feed ratio of 6.5 H2/n-C7 and WHSV of 2.98 h−1.
Open AccessHydroisomerisation and Hydrocracking of n-Heptane: Modelling and Optimisation Using a Hybrid Artificial Neural Network–Genetic Algorithm (ANN–GA)
In this paper, the focus is on upgrading the value of naphtha compounds represented by n-heptane (n-C7H16) with zero octane number using a commercial zeolite catalyst consisting of a mixture of 75% HY and 25% HZSM-5 loaded with different amounts, 0.25 to 1 wt.%, of platinum metal. Hydrocracking and hydroisomerisation processes are experimentally and theoretically studied in the temperature range of 300–400 °C and under various contact times. A feedforward artificial neural network (FFANN) based on two hidden layers was used for the purpose of process modelling. A total of 80% of the experimental results was used to train the artificial neural network, with the remaining results being used for evaluation and testing of the network. Tan-sigmoid and log-sigmoid transfer functions were used in the first and second hidden layers, respectively. The optimum number of neurons in hidden layers was determined depending on minimising the mean absolute error (MAE). The best ANN model, represented by the multilayer FFANN, had a 4–24–24–12 topology. The ANN model accurately simulates the process in which the correlation coefficient (R2) was found to be 0.9918, 0.9492, and 0.9426 for training, validation, and testing, respectively, and an average of 0.9767 for all data. In addition, the operating conditions of the process were optimised using the genetic algorithm (GA) towards increasing the octane number of the products. MATLAB® Version 2020a was utilised to complete all required computations and predictions. Optimal operating conditions were found through the theoretical study: 0.85 wt.% Pt-metal loaded, 359.36 °C, 6.562 H2/n-heptane feed ratio, and 3.409 h−1 weight-hourly space velocity (WHSV), through which the maximum octane number (RON) of 106.84 was obtained. Finally, those operating conditions largely matched what was calculated from the results of the experimental study, where the highest percentage of the resulting isomers was found with about 78.7 mol% on the surface of the catalyst loaded with 0.75 wt.% Pt-metal at 350 °C using a feed ratio of 6.5 H2/n-C7 and WHSV of 2.98 h−1.
- 1 July 2023
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 63 (7) , 829-843
Bimetallic Catalysts for Isomerization of Alkanes (A Review)
Incorporating a second metal into the monometallic bifunctional catalyst structure results in appearance of new catalytic characteristics and increase in the catalytic productivity. This type of catalyst is called bimetallic catalyst, which is better than a monometallic one in industrial processes, because it enhances some catalytic features like metal dispersion, activity, selectivity, stability, and lifespan. Different researches have asserted that the bimetallic catalyst increases the yield of the desired branched alkanes and decreases the undesired low-molecular-weight gaseous products. The enhancement of catalytic properties of the bimetallic catalyst is ascribed mainly to the electronic features and geometric structure of nanoparticles of two metals and increases the Lewis acidity and balance between metals and a supporter. In this paper, the theoretical and experimental fundamentals of bimetallic catalysis are reviewed based on many trusted experimental works of different researchers.
- 1 July 2023
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 63 (7) , 829-843
Bimetallic Catalysts for Isomerization of Alkanes (A Review)
Incorporating a second metal into the monometallic bifunctional catalyst structure results in appearance of new catalytic characteristics and increase in the catalytic productivity. This type of catalyst is called bimetallic catalyst, which is better than a monometallic one in industrial processes, because it enhances some catalytic features like metal dispersion, activity, selectivity, stability, and lifespan. Different researches have asserted that the bimetallic catalyst increases the yield of the desired branched alkanes and decreases the undesired low-molecular-weight gaseous products. The enhancement of catalytic properties of the bimetallic catalyst is ascribed mainly to the electronic features and geometric structure of nanoparticles of two metals and increases the Lewis acidity and balance between metals and a supporter. In this paper, the theoretical and experimental fundamentals of bimetallic catalysis are reviewed based on many trusted experimental works of different researchers.
- Open Access
Optimization of Polypropylene Waste Recycling Products as Alternative Fuels through Non-Catalytic Thermal and Catalytic Hydrocracking Using Fresh and Spent Pt/Al2O3 and NiMo/Al2O3 Catalysts
In this work, the conversion of waste polypropylene to alternative fuels (liquid and gas) was performed through non-catalytic thermal and catalytic hydrocracking over NiMo/Al2O3 and Pt/Al2O3 catalysts. The process was carried out in an autoclave batch reactor at a temperature of 450 °C and a pressure of 20 bar, which were selected based on experimental optimization. The spent catalyst was also successfully regenerated at 700 °C under a hot airflow. Experiments were conducted to determine the optimum conditions to completely separate the deactivated catalyst from the solid residue easily. The regenerated catalyst was reused to facilitate the economic cost reduction of the process. The reactivated catalysts have almost the same catalytic properties as the fresh catalysts; this was confirmed by several characterization techniques, such as TGA, XRD, SEM, EDX, BET and FTIR. The produced liquids/gases were quantified and classified into their fractions by the number of carbon atoms and gasoline to diesel ratio using GC/MS. The viscosity, density, API gravity, pour point and flash point of oil cuts were also investigated to evaluate the quality of the resulting liquid from the reactions. The NiMo/Al2O3 catalyst gave the highest liquid hydrocarbons yield of 86 wt%, while the highest weight products of gasoline range hydrocarbon fractions of 49.85 wt% were found over the Pt/Al2O3 catalyst. Almost the same catalytic behavior was found with the regenerated catalysts compared to the fresh catalysts. However, the highest gaseous products at 20.8 wt% were found in the non-catalytic thermal products with an increase in the diesel fuel range of 80.83 wt%. The kinetic model was implemented using six lumps and fifteen reactions, and the apparent activation energies for the gasoline and diesel fractions were calculated. In general, all primary and secondary reactions show greater activation energy values on the Pt/Al2O3 catalyst than on the NiMo/Al2O3 catalyst.
Open AccessOptimization of Polypropylene Waste Recycling Products as Alternative Fuels through Non-Catalytic Thermal and Catalytic Hydrocracking Using Fresh and Spent Pt/Al2O3 and NiMo/Al2O3 Catalysts
In this work, the conversion of waste polypropylene to alternative fuels (liquid and gas) was performed through non-catalytic thermal and catalytic hydrocracking over NiMo/Al2O3 and Pt/Al2O3 catalysts. The process was carried out in an autoclave batch reactor at a temperature of 450 °C and a pressure of 20 bar, which were selected based on experimental optimization. The spent catalyst was also successfully regenerated at 700 °C under a hot airflow. Experiments were conducted to determine the optimum conditions to completely separate the deactivated catalyst from the solid residue easily. The regenerated catalyst was reused to facilitate the economic cost reduction of the process. The reactivated catalysts have almost the same catalytic properties as the fresh catalysts; this was confirmed by several characterization techniques, such as TGA, XRD, SEM, EDX, BET and FTIR. The produced liquids/gases were quantified and classified into their fractions by the number of carbon atoms and gasoline to diesel ratio using GC/MS. The viscosity, density, API gravity, pour point and flash point of oil cuts were also investigated to evaluate the quality of the resulting liquid from the reactions. The NiMo/Al2O3 catalyst gave the highest liquid hydrocarbons yield of 86 wt%, while the highest weight products of gasoline range hydrocarbon fractions of 49.85 wt% were found over the Pt/Al2O3 catalyst. Almost the same catalytic behavior was found with the regenerated catalysts compared to the fresh catalysts. However, the highest gaseous products at 20.8 wt% were found in the non-catalytic thermal products with an increase in the diesel fuel range of 80.83 wt%. The kinetic model was implemented using six lumps and fifteen reactions, and the apparent activation energies for the gasoline and diesel fractions were calculated. In general, all primary and secondary reactions show greater activation energy values on the Pt/Al2O3 catalyst than on the NiMo/Al2O3 catalyst.