Leonardo Galli Engler
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Leonardo Galli Engler has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Declan M. Devine
PRISM Research Institute, Technological University of the Shannon, N37 HD68 Athlone, Ireland
3 shared publications - Ian Major
PRISM Research Institute, Technological University of the Shannon, Athlone N37 HD68, Ireland
3 shared publications - Janaina Silva Crespo
Universidade de Caxias do Sul
2 shared publications - Noel Gately
Technology Transfer Office, Technological University of the Shannon, University Road, N37HD68 Athlone, Ireland
2 shared publications - Jadna Catafesta
Universidade de Caxias do Sul, 95070-560 Caxias do Sul, Rio Grande do Sul, Brazil
1 shared publication Janaina S. Crespo
PRISM Research Institute Technological University of the Shannon: Midlands Midwest Athlone Ireland
1 shared publication
Latest Publications
- Open Access
- 9 January 2025
- Published by Wiley in Journal of Biomedical Materials Research Part A
- Vol. 113 (1) , e37857
Exploring the Synergy of Metallic Antimicrobial Agents in Ternary Blends of PHB/PLA/PCL
This study provides a comprehensive investigation of antimicrobial additives (ZnO/AgNPs and SiO2/AgNPs) on the properties of biodegradable ternary blends composed of poly(hydroxybutyrate) (PHB), poly(lactic acid) (PLA), and polycaprolactone (PCL) by examining the morphology, thermal stability, crystallinity index, and cell viability of these blends. Overall, transmission electron microscopy (TEM) analysis revealed that AgNPs and SiO2 exhibited comparable sizes, whereas ZnO was significantly larger, which influences their release profiles and interactions with the blends. The addition of antimicrobials influences the rheology of the blends, acting as compatibilizers by reducing the intermolecular forces between biopolymers. Scanning electron microscopy (SEM) analysis revealed a matrix–core–shell structure, indicating enhanced interfacial interaction among the immiscible biopolymers, as predicted by their spreading coefficient. From thermal evaluations, PCL promotes overall thermal stability, where T5 (the temperature at which the sample loses 5% of its weight through thermal degradation) was more than 22% higher than T5 of blends, and the antimicrobials investigated tend to act as barriers to heat penetration, thereby influencing the degradation mechanism of the blends. Additionally, antimicrobials tend to increase material crystallinity, suggesting their nucleating effect. Both PLA and PCL have shown high viability for cell growth and proliferation. The 30/50/20 (PHB/PLA/PCL wt%) blends were conducive to cell adhesion and proliferation, achieving cell viability rates up to 85% irrespective of the antimicrobial concentration. SEM analysis also confirmed the presence of viable cells and attachment of organic cell structures over the surface of the produced materials. In conclusion, this study highlights the potential of biodegradable ternary blends containing antimicrobial NPs, particularly for use in medical devices such as ureteral stents.
- 9 January 2025
- Published by Wiley in Journal of Biomedical Materials Research Part A
- Vol. 113 (1) , e37857
Open AccessExploring the Synergy of Metallic Antimicrobial Agents in Ternary Blends of PHB/PLA/PCL
This study provides a comprehensive investigation of antimicrobial additives (ZnO/AgNPs and SiO2/AgNPs) on the properties of biodegradable ternary blends composed of poly(hydroxybutyrate) (PHB), poly(lactic acid) (PLA), and polycaprolactone (PCL) by examining the morphology, thermal stability, crystallinity index, and cell viability of these blends. Overall, transmission electron microscopy (TEM) analysis revealed that AgNPs and SiO2 exhibited comparable sizes, whereas ZnO was significantly larger, which influences their release profiles and interactions with the blends. The addition of antimicrobials influences the rheology of the blends, acting as compatibilizers by reducing the intermolecular forces between biopolymers. Scanning electron microscopy (SEM) analysis revealed a matrix–core–shell structure, indicating enhanced interfacial interaction among the immiscible biopolymers, as predicted by their spreading coefficient. From thermal evaluations, PCL promotes overall thermal stability, where T5 (the temperature at which the sample loses 5% of its weight through thermal degradation) was more than 22% higher than T5 of blends, and the antimicrobials investigated tend to act as barriers to heat penetration, thereby influencing the degradation mechanism of the blends. Additionally, antimicrobials tend to increase material crystallinity, suggesting their nucleating effect. Both PLA and PCL have shown high viability for cell growth and proliferation. The 30/50/20 (PHB/PLA/PCL wt%) blends were conducive to cell adhesion and proliferation, achieving cell viability rates up to 85% irrespective of the antimicrobial concentration. SEM analysis also confirmed the presence of viable cells and attachment of organic cell structures over the surface of the produced materials. In conclusion, this study highlights the potential of biodegradable ternary blends containing antimicrobial NPs, particularly for use in medical devices such as ureteral stents.
- Open Access
Designing Sustainable Polymer Blends: Tailoring Mechanical Properties and Degradation Behaviour in PHB/PLA/PCL Blends in a Seawater Environment
Biodegradable polyesters are a popular choice for both packaging and medical device manufacture owing to their ability to break down into harmless components once they have completed their function. However, commonly used polyesters such as poly(hydroxybutyrate) (PHB), poly(lactic acid) (PLA), and polycaprolactone (PCL), while readily available and have a relatively low price compared to other biodegradable polyesters, do not meet the degradation profiles required for many applications. As such, this study aimed to determine if the mechanical and degradation properties of biodegradable polymers could be tailored by blending different polymers. The seawater degradation mechanisms were evaluated, revealing surface erosion and bulk degradation in the blends. The extent of degradation was found to be dependent on the specific chemical composition of the polymer and the blend ratio, with degradation occurring via hydrolytic, enzymatic, oxidative, or physical pathways. PLA presents the highest tensile strength (67 MPa); the addition of PHB and PCL increased the flexibility of the samples; however, the tensile strength reduced to 25.5 and 18 MPa for the blends 30/50/20 and 50/25/25, respectively. Additionally, PCL presented weight loss of up to 10 wt.% and PHB of up to 6 wt.%; the seawater degradation in the blends occurs by bulk and surface erosion. The blending process facilitated the flexibility of the blends, enabling their use in diverse industrial applications such as medical devices and packaging. The proposed methodology produced biodegradable blends with tailored properties within a seawater environment. Additionally, further tests that fully track the biodegradation process should be put in place; incorporating compatibilizers might promote the miscibility of different polymers, improving their mechanical properties and biodegradability.
Open AccessDesigning Sustainable Polymer Blends: Tailoring Mechanical Properties and Degradation Behaviour in PHB/PLA/PCL Blends in a Seawater Environment
Biodegradable polyesters are a popular choice for both packaging and medical device manufacture owing to their ability to break down into harmless components once they have completed their function. However, commonly used polyesters such as poly(hydroxybutyrate) (PHB), poly(lactic acid) (PLA), and polycaprolactone (PCL), while readily available and have a relatively low price compared to other biodegradable polyesters, do not meet the degradation profiles required for many applications. As such, this study aimed to determine if the mechanical and degradation properties of biodegradable polymers could be tailored by blending different polymers. The seawater degradation mechanisms were evaluated, revealing surface erosion and bulk degradation in the blends. The extent of degradation was found to be dependent on the specific chemical composition of the polymer and the blend ratio, with degradation occurring via hydrolytic, enzymatic, oxidative, or physical pathways. PLA presents the highest tensile strength (67 MPa); the addition of PHB and PCL increased the flexibility of the samples; however, the tensile strength reduced to 25.5 and 18 MPa for the blends 30/50/20 and 50/25/25, respectively. Additionally, PCL presented weight loss of up to 10 wt.% and PHB of up to 6 wt.%; the seawater degradation in the blends occurs by bulk and surface erosion. The blending process facilitated the flexibility of the blends, enabling their use in diverse industrial applications such as medical devices and packaging. The proposed methodology produced biodegradable blends with tailored properties within a seawater environment. Additionally, further tests that fully track the biodegradation process should be put in place; incorporating compatibilizers might promote the miscibility of different polymers, improving their mechanical properties and biodegradability.
- Open Access
- 12 October 2022
- Published by MDPI AG in Journal of Composites Science
- Vol. 6 (10) , 309
Process Optimization for the 3D Printing of PLA and HNT Composites with Arburg Plastic Freeforming
The industrial use of additive manufacturing continues to rapidly increase as new technology developments become available. The Arburg plastic freeforming (APF) process is designed to utilize standard polymeric granules in order to print parts with properties similar to those of molded parts. Despite the emerging industrial importance of APF, the current body of knowledge regarding this technology is still very limited, especially in the field of biodegradable polymer composites. To this end, poly(lactic acid) (PLA) was reinforced with halloysite nanotubes (HNTs) by hot melt extrusion. The PLA/HNT (0–10 wt%.) composites were analyzed in terms of their rheology, morphology, and thermal and mechanical properties. A study of the processing properties of these composites in the context of APF was performed to ensure the consistency of 3D-printed, high-quality components. The optimized machine settings were used to evaluate the tensile properties of specimens printed with different axis orientations (XY and XZ) and deposition angles (0 and 45°). Specimens printed with an XY orientation and deposition angle starting at 0° resulted in the highest mechanical properties. In this study, the use of PLA/HNT composites in an APF process was reported for the first time, and the current methodology achieved satisfactory results in terms of the 3D printing and evaluation of successful PLA/HNT composites to be used as feedstock in an APF process.
- 12 October 2022
- Published by MDPI AG in Journal of Composites Science
- Vol. 6 (10) , 309
Open AccessProcess Optimization for the 3D Printing of PLA and HNT Composites with Arburg Plastic Freeforming
The industrial use of additive manufacturing continues to rapidly increase as new technology developments become available. The Arburg plastic freeforming (APF) process is designed to utilize standard polymeric granules in order to print parts with properties similar to those of molded parts. Despite the emerging industrial importance of APF, the current body of knowledge regarding this technology is still very limited, especially in the field of biodegradable polymer composites. To this end, poly(lactic acid) (PLA) was reinforced with halloysite nanotubes (HNTs) by hot melt extrusion. The PLA/HNT (0–10 wt%.) composites were analyzed in terms of their rheology, morphology, and thermal and mechanical properties. A study of the processing properties of these composites in the context of APF was performed to ensure the consistency of 3D-printed, high-quality components. The optimized machine settings were used to evaluate the tensile properties of specimens printed with different axis orientations (XY and XZ) and deposition angles (0 and 45°). Specimens printed with an XY orientation and deposition angle starting at 0° resulted in the highest mechanical properties. In this study, the use of PLA/HNT composites in an APF process was reported for the first time, and the current methodology achieved satisfactory results in terms of the 3D printing and evaluation of successful PLA/HNT composites to be used as feedstock in an APF process.
- 15 February 2019
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 136 (24)
Nano/microfibers of EVA copolymer obtained by solution blow spinning: Processing, solution properties, and pheromone release application
Pheromones have been used for monitoring and control of insect pests in crops, reducing the use of pesticides. However, among obstacles for this technology to be more useful, is the control and time to release. In this way, this work aims the evaluation of the release of pheromones using micro/nanofibers of ethylene–vinyl acetate (EVA) produced by blow spinning. Solutions with 0.5–15 wt % EVA were prepared based on the solubility parameter of the copolymer. Fibers were obtained from solutions in the semidiluted concentration regime. Synthetic sex pheromones from the oriental fruit moth, Grapholita molesta and citrus leafminer Phyllocnistis citrella were incorporated into the micro/nanofibers. The morphology and structure of these fibers were evaluated employing field emission scanning electron microscopy and wide‐angle X‐ray diffraction. The fibers sizes (95–426 nm) were dependent on the feed rate of the solution. As a result, pheromone release has occurred linearly over 10 weeks, as determined by thermogravimetry analysis. The solubility parameter influences the amount incorporated in the fiber and the rate of pheromone release. The proposed fiber/pheromone system is interesting since it reduces the use of actives and can be used in several planting cycles and reused. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019, 136, 47647.
- 15 February 2019
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 136 (24)
Nano/microfibers of EVA copolymer obtained by solution blow spinning: Processing, solution properties, and pheromone release application
Pheromones have been used for monitoring and control of insect pests in crops, reducing the use of pesticides. However, among obstacles for this technology to be more useful, is the control and time to release. In this way, this work aims the evaluation of the release of pheromones using micro/nanofibers of ethylene–vinyl acetate (EVA) produced by blow spinning. Solutions with 0.5–15 wt % EVA were prepared based on the solubility parameter of the copolymer. Fibers were obtained from solutions in the semidiluted concentration regime. Synthetic sex pheromones from the oriental fruit moth, Grapholita molesta and citrus leafminer Phyllocnistis citrella were incorporated into the micro/nanofibers. The morphology and structure of these fibers were evaluated employing field emission scanning electron microscopy and wide‐angle X‐ray diffraction. The fibers sizes (95–426 nm) were dependent on the feed rate of the solution. As a result, pheromone release has occurred linearly over 10 weeks, as determined by thermogravimetry analysis. The solubility parameter influences the amount incorporated in the fiber and the rate of pheromone release. The proposed fiber/pheromone system is interesting since it reduces the use of actives and can be used in several planting cycles and reused. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019, 136, 47647.