Yuantao Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Yuantao Wang has a total of 105 co-authors. Here are the top co-authors by number of shared publications:
- Damianos Pavlidis
Institute of Chemical Engineering Sciences (FORTH/ICE-HT)
5 shared publications - David M. Bell
Paul Scherrer Institute
5 shared publications Andre S. H. Prevot
4 shared publications- Andreas Aktypis
Department of Chemical Engineering, University of Patras, Patras, Greece
4 shared publications - Christos Kaltsonoudis
Institute of Chemical Engineering Sciences, ICE-HT, Patras, 26504, Greece
4 shared publications - Imad El Haddad
PSI Center for Energy and Environmental Sciences, Paul Scherrer Institute, Villigen, Switzerland
4 shared publications
Latest Publications
- Open Access
- 14 October 2026
- Published by American Chemical Society (ACS) in Environmental Science & Technology
- Vol. 60 (42) , 29992-30007
Toward Recreating the Breath of Cities in the Atmospheric Simulation Chamber SAPHIR
Atmospheric simulation chambers are essential for studying oxidation processes, yet many experiments rely on single-precursor systems at concentrations that limit their representativeness for the chemical complexity of urban air. Here, we present a framework linking emission inventories, chamber experiments, and field observations by constructing emission fingerprints of major urban sources, including vegetation, volatile chemical products, cooking emissions, and gasoline and diesel exhaust. Applied during the CHANEL campaign in the SAPHIR outdoor chamber, these fingerprints advanced toward reproducing gas-phase mixtures representative of Los Angeles (gasoline-dominated traffic), a diesel-dominated city, and a future low-vehicle-emission scenario. The resulting mixtures generated peroxy-to-hydroperoxy radical ratios (RO2/HO2) close to unity, bimolecular RO2 lifetimes comparable with urban atmospheric observations, although lower NO levels favored RO2 + HO2 over RO2 + NO reactions. Comparison with aircraft measurements over Los Angeles using ammonium (NH4+) chemical ionization mass spectrometry showed reasonable agreement, with 465 organic product ions detected in both data sets, representing 78% of the product ions observed in the ambient air. Furthermore, 87% of common product ions agreed within a factor of 3 of the linear correlation, demonstrating that chamber experiments can capture key aspects of both atmospherically relevant radical chemistry and the oxidation product diversity of urban air.
- 14 October 2026
- Published by American Chemical Society (ACS) in Environmental Science & Technology
- Vol. 60 (42) , 29992-30007
Open AccessToward Recreating the Breath of Cities in the Atmospheric Simulation Chamber SAPHIR
Atmospheric simulation chambers are essential for studying oxidation processes, yet many experiments rely on single-precursor systems at concentrations that limit their representativeness for the chemical complexity of urban air. Here, we present a framework linking emission inventories, chamber experiments, and field observations by constructing emission fingerprints of major urban sources, including vegetation, volatile chemical products, cooking emissions, and gasoline and diesel exhaust. Applied during the CHANEL campaign in the SAPHIR outdoor chamber, these fingerprints advanced toward reproducing gas-phase mixtures representative of Los Angeles (gasoline-dominated traffic), a diesel-dominated city, and a future low-vehicle-emission scenario. The resulting mixtures generated peroxy-to-hydroperoxy radical ratios (RO2/HO2) close to unity, bimolecular RO2 lifetimes comparable with urban atmospheric observations, although lower NO levels favored RO2 + HO2 over RO2 + NO reactions. Comparison with aircraft measurements over Los Angeles using ammonium (NH4+) chemical ionization mass spectrometry showed reasonable agreement, with 465 organic product ions detected in both data sets, representing 78% of the product ions observed in the ambient air. Furthermore, 87% of common product ions agreed within a factor of 3 of the linear correlation, demonstrating that chamber experiments can capture key aspects of both atmospherically relevant radical chemistry and the oxidation product diversity of urban air.
- Open Access
- 11 July 2026
- Published by American Chemical Society (ACS) in Environmental Science & Technology Letters
- Vol. 13 (8) , 1145-1150
Emissions of Volatile Methyl Siloxanes (VMS) from Vehicles
Volatile methyl siloxanes (VMS) are anthropogenic compounds widely used in personal care products and industrial applications and are frequently detected at elevated concentrations in urban air. However, their sources in urban areas remain poorly constrained. Here, we use chassis dynamometer experiments to quantify gas-phase VMS emissions from a range of on-road vehicles, including light-duty gasoline and diesel vehicles. Hexamethylcyclotrisiloxane (D3) dominated the emitted VMS, over octamethylcyclotetrasiloxane (D4), and decamethylcyclopentasiloxane (D5). VMS emissions increased with driving speed and were substantially higher from gasoline than from diesel vehicles. Comparison with tunnel measurements showing elevated ambient VMS concentrations supports a significant contribution from traffic-related sources, including tailpipe and potentially nontailpipe emissions. These results identify vehicular emissions as a previously underrecognized source of VMS near highways, and provide new constraints for their atmospheric budget and source apportionment.
- 11 July 2026
- Published by American Chemical Society (ACS) in Environmental Science & Technology Letters
- Vol. 13 (8) , 1145-1150
Open AccessEmissions of Volatile Methyl Siloxanes (VMS) from Vehicles
Volatile methyl siloxanes (VMS) are anthropogenic compounds widely used in personal care products and industrial applications and are frequently detected at elevated concentrations in urban air. However, their sources in urban areas remain poorly constrained. Here, we use chassis dynamometer experiments to quantify gas-phase VMS emissions from a range of on-road vehicles, including light-duty gasoline and diesel vehicles. Hexamethylcyclotrisiloxane (D3) dominated the emitted VMS, over octamethylcyclotetrasiloxane (D4), and decamethylcyclopentasiloxane (D5). VMS emissions increased with driving speed and were substantially higher from gasoline than from diesel vehicles. Comparison with tunnel measurements showing elevated ambient VMS concentrations supports a significant contribution from traffic-related sources, including tailpipe and potentially nontailpipe emissions. These results identify vehicular emissions as a previously underrecognized source of VMS near highways, and provide new constraints for their atmospheric budget and source apportionment.
- Open Access
- 13 March 2026
- Published by Copernicus GmbH
Secondary Organic Aerosol Formation from Emissions of On- and Off-Road Vehicles
Tailpipe emissions from on- and off-road vehicles can be a significant source of secondary organic aerosol (SOA) both in urban areas and regionally. However, major uncertainties remain in understanding SOA formation from vehicle exhaust in different oxidation timescales.Individual on- and off-road vehicles were tested on a dynamometer, with their exhaust introduced into an oxidation flow reactor (OFR) and an atmospheric simulation chamber to investigate SOA formation across a range of OH exposures. Exposures approximately ranged from very short durations of 0.1 up to 9 equivalent days, with the smog chamber experiments corresponding on average to 2 equivalent days. In total, emissions from 14 vehicles, including 4 gasoline cars, 4 diesel cars, 4 scooters, and 2 tractors, covering a range of engine types and control technologies, were examined. Standardized driving cycles were followed, including WLTC for passenger cars, WMTC for scooters, and NRSC for tractors. The on-road cycles, carried out on a chassis dynamometer, simulated urban-speed conditions and included cold starts, while the off-road cycle consisted of steady-state engine operation at multiple loads and speeds, controlled by an EGGERS dynamometer.Scanning mobility particle sizers (SMPS) were used to measure particle size distributions, while the chemical composition was characterized by a high-resolution aerosol mass spectrometer (HR-ToF-AMS) for the aerosol and by a VOCUS Proton-Transfer-Reaction-Mass-Spectrometer (VOCUS PTR-MS) for the gas phase. Black carbon and trace gases were monitored using an aethalometer (AE33) and online gas analyzers, respectively. The volatility distribution of SOA in the 1-D volatility basis set (VBS) was also characterized using a combination of thermodenuder measurements and TD-GCMS analysis of Tenax sorbent tubes sampled from the smog chamber after the oxidation.Two-wheelers, especially a pre-Euro 2-stroke scooter, had the highest SOA formation potential (SOAFP) across the full range of OH exposure, exceeding all other on-road vehicle types by more than an order of magnitude, where SOAFP is defined as the amount of SOA formed per kg of fuel burned. A modern off-road tractor (Stage V) also showed substantial SOAFP surpassing a modern scooter (Euro 5) and the rest on-road vehicles. Euro 6 gasoline on-road cars exhibited higher SOAFP values than Euro 6 diesel vehicles. These results highlight the disproportionate contribution of scooters and off-road vehicles to urban SOA, underlining the need for targeted emission control strategies.
- 13 March 2026
- Published by Copernicus GmbH
Open AccessSecondary Organic Aerosol Formation from Emissions of On- and Off-Road Vehicles
Tailpipe emissions from on- and off-road vehicles can be a significant source of secondary organic aerosol (SOA) both in urban areas and regionally. However, major uncertainties remain in understanding SOA formation from vehicle exhaust in different oxidation timescales.Individual on- and off-road vehicles were tested on a dynamometer, with their exhaust introduced into an oxidation flow reactor (OFR) and an atmospheric simulation chamber to investigate SOA formation across a range of OH exposures. Exposures approximately ranged from very short durations of 0.1 up to 9 equivalent days, with the smog chamber experiments corresponding on average to 2 equivalent days. In total, emissions from 14 vehicles, including 4 gasoline cars, 4 diesel cars, 4 scooters, and 2 tractors, covering a range of engine types and control technologies, were examined. Standardized driving cycles were followed, including WLTC for passenger cars, WMTC for scooters, and NRSC for tractors. The on-road cycles, carried out on a chassis dynamometer, simulated urban-speed conditions and included cold starts, while the off-road cycle consisted of steady-state engine operation at multiple loads and speeds, controlled by an EGGERS dynamometer.Scanning mobility particle sizers (SMPS) were used to measure particle size distributions, while the chemical composition was characterized by a high-resolution aerosol mass spectrometer (HR-ToF-AMS) for the aerosol and by a VOCUS Proton-Transfer-Reaction-Mass-Spectrometer (VOCUS PTR-MS) for the gas phase. Black carbon and trace gases were monitored using an aethalometer (AE33) and online gas analyzers, respectively. The volatility distribution of SOA in the 1-D volatility basis set (VBS) was also characterized using a combination of thermodenuder measurements and TD-GCMS analysis of Tenax sorbent tubes sampled from the smog chamber after the oxidation.Two-wheelers, especially a pre-Euro 2-stroke scooter, had the highest SOA formation potential (SOAFP) across the full range of OH exposure, exceeding all other on-road vehicle types by more than an order of magnitude, where SOAFP is defined as the amount of SOA formed per kg of fuel burned. A modern off-road tractor (Stage V) also showed substantial SOAFP surpassing a modern scooter (Euro 5) and the rest on-road vehicles. Euro 6 gasoline on-road cars exhibited higher SOAFP values than Euro 6 diesel vehicles. These results highlight the disproportionate contribution of scooters and off-road vehicles to urban SOA, underlining the need for targeted emission control strategies.
- Open Access
- 15 March 2025
- Published by Copernicus GmbH
Exploring the oxidative potential of vehicles emissions from bench dynamometer to underground tunnels and parking lots
Health effects associated with aerosol exposure have been widely studied, demonstrating a positive association with mortality and poor health from a diversity of ailments. Emissions from vehicular traffic have been a major source of air pollutants, especially in urban and highly-populated environments, and emissions controls have considerably reduced the amount of aerosol from these sources. Nevertheless, policy based on mass concentration alone overlooks the possibility that certain aerosol sources may be more toxic than others. To address this, oxidative potential (OP) has been used as a metric that incorporates these properties, and ties in together mass and toxicity into a single metric that is a proxy of oxidative stress – thought to be a mechanism associated with adverse health effects from particulate matter exposure.In this work, we focus on evaluating the oxidative potential of vehicular emissions using the dithiothreitol assay (DTT) during various field observations conducted as part of the EASOLEE project. Emissions from controlled environmental and driving conditions were characterized to compare diverse types of vehicles. Real driving conditions for large vehicle fleets inside a 12 km underground tunnel connecting France with Italy, as well as emissions from an underground parking lot were characterized. Our results showed a lower OP mass normalized (OPm) for fresh particles compared to aged particles. Diesel vehicles (47±67 pmol DTT min-1 μg-1) also exhibited a lower OPm when compared to scooters and gasoline vehicles (142±193 pmol DTT min-1 μg-1 and 130±75 pmol DTT min-1 μg-1 respectively). Measurements in the tunnel also revealed a lower OPm on average than previous studies (below 6 pmol DTT min-1 μg-1), possibly from the usage of a more modern ventilation system; in all cases, aging of the primary emissions led to more OP-active aerosol, with an enhancement of up to a factor of 10 in some cases. The implications therefore are that health impacts of particles away from their sources, especially certain types of vehicles, may be affected by increases of their toxicity from atmospheric aging.
- 15 March 2025
- Published by Copernicus GmbH
Open AccessExploring the oxidative potential of vehicles emissions from bench dynamometer to underground tunnels and parking lots
Health effects associated with aerosol exposure have been widely studied, demonstrating a positive association with mortality and poor health from a diversity of ailments. Emissions from vehicular traffic have been a major source of air pollutants, especially in urban and highly-populated environments, and emissions controls have considerably reduced the amount of aerosol from these sources. Nevertheless, policy based on mass concentration alone overlooks the possibility that certain aerosol sources may be more toxic than others. To address this, oxidative potential (OP) has been used as a metric that incorporates these properties, and ties in together mass and toxicity into a single metric that is a proxy of oxidative stress – thought to be a mechanism associated with adverse health effects from particulate matter exposure.In this work, we focus on evaluating the oxidative potential of vehicular emissions using the dithiothreitol assay (DTT) during various field observations conducted as part of the EASOLEE project. Emissions from controlled environmental and driving conditions were characterized to compare diverse types of vehicles. Real driving conditions for large vehicle fleets inside a 12 km underground tunnel connecting France with Italy, as well as emissions from an underground parking lot were characterized. Our results showed a lower OP mass normalized (OPm) for fresh particles compared to aged particles. Diesel vehicles (47±67 pmol DTT min-1 μg-1) also exhibited a lower OPm when compared to scooters and gasoline vehicles (142±193 pmol DTT min-1 μg-1 and 130±75 pmol DTT min-1 μg-1 respectively). Measurements in the tunnel also revealed a lower OPm on average than previous studies (below 6 pmol DTT min-1 μg-1), possibly from the usage of a more modern ventilation system; in all cases, aging of the primary emissions led to more OP-active aerosol, with an enhancement of up to a factor of 10 in some cases. The implications therefore are that health impacts of particles away from their sources, especially certain types of vehicles, may be affected by increases of their toxicity from atmospheric aging.
- Open Access
- 15 March 2025
- Published by Copernicus GmbH
Emission Factors of Primary Pollutants from a Real-world Tunnel Measurement
With over 1.6 billion vehicles worldwide, the combustion of fossil fuels is a major source of particulate matter (PM) and trace gases, which significantly contribute to air pollution, climate change and cause health burden. Heavy-duty vehicles (HDVs) constitute a small fraction of the global vehicle population but account for a disproportionately large share of total emissions when compared with light-duty vehicles (LDVs). However, uncertainty remains about which vehicle type contribute most to the emission factors (EFs) of various pollutants, particularly in Europe, where diesel technology has historically been favored for LDVs.Because traditional engine emission tests may not accurately reflect the real-world emissions, there is a need for on-road, real-world emission assessments. In this study, we conducted a three-week measurement campaign in the Fréjus Road Tunnel using MIRO MGA-10, aethalometer and SMPS. We developed a practical method to determine the EFs of primary pollutants, including trace gases (NOx, CO2, CO, N2O, NH3, CH4), black carbon (BC), and ultrafine particles (UFP). The calculated EFs will be reported, and selected pollutant species will be compared with previously published data from Asia and America in equivalent units.Figure 1 shows the results for the species mentioned, where HDV* indicates the proportion of HDVs to the total number of vehicles, taking into account the CO2 emissions from a single HDV and LDV. The results indicated that for most pollutant species, LDVs exhibited higher EFs than HDVs. However, HDVs emitted a higher fraction of N2O compared to LDVs. The EFs of NOx, CO, BC, and NH3 were consistent with previous studies conducted in Europe but lower than data reported from Asia and America. This study’s findings will raise public awareness and provide valuable insights for policymakers to develop strategies to mitigate emissions. Figure 1. Emission Factors (g/kg fuel)
- 15 March 2025
- Published by Copernicus GmbH
Open AccessEmission Factors of Primary Pollutants from a Real-world Tunnel Measurement
With over 1.6 billion vehicles worldwide, the combustion of fossil fuels is a major source of particulate matter (PM) and trace gases, which significantly contribute to air pollution, climate change and cause health burden. Heavy-duty vehicles (HDVs) constitute a small fraction of the global vehicle population but account for a disproportionately large share of total emissions when compared with light-duty vehicles (LDVs). However, uncertainty remains about which vehicle type contribute most to the emission factors (EFs) of various pollutants, particularly in Europe, where diesel technology has historically been favored for LDVs.Because traditional engine emission tests may not accurately reflect the real-world emissions, there is a need for on-road, real-world emission assessments. In this study, we conducted a three-week measurement campaign in the Fréjus Road Tunnel using MIRO MGA-10, aethalometer and SMPS. We developed a practical method to determine the EFs of primary pollutants, including trace gases (NOx, CO2, CO, N2O, NH3, CH4), black carbon (BC), and ultrafine particles (UFP). The calculated EFs will be reported, and selected pollutant species will be compared with previously published data from Asia and America in equivalent units.Figure 1 shows the results for the species mentioned, where HDV* indicates the proportion of HDVs to the total number of vehicles, taking into account the CO2 emissions from a single HDV and LDV. The results indicated that for most pollutant species, LDVs exhibited higher EFs than HDVs. However, HDVs emitted a higher fraction of N2O compared to LDVs. The EFs of NOx, CO, BC, and NH3 were consistent with previous studies conducted in Europe but lower than data reported from Asia and America. This study’s findings will raise public awareness and provide valuable insights for policymakers to develop strategies to mitigate emissions. Figure 1. Emission Factors (g/kg fuel)
- Open Access
- 15 March 2025
- Published by Copernicus GmbH
Emissions of Volatile Methyl Siloxanes (VMSs) from Vehicles
Volatile Methyl Siloxanes (VMSs) are anthropogenic molecules emitted from personal care products and industrial chemical products. Recent studies have found that concentrations of VMSs tend to be higher in densely populated urban areas, although research in large urban centers remains limited. Toxicity of such molecules remain uncertain with often conflicting reports. Previous literature has also reported the presence of long chain siloxanes in the particle phase from traffic emissions, and represented the first identification and quantification of siloxanes mostly likely emitted from vehicles.In this study, the chassis dynamometer measurements were conducted to characterize the gaseous components from a variety of vehicles, including gasoline passenger cars, diesel passenger cars, and scooters. Time-resolved volatile organic compound (VOC) emissions during the cold start through a full driving cycle from different vehicles were chemically characterized by the Vocus proton-transfer-reaction time-of-flight mass spectrometer (VOCUS PTR-TOF-MS). The emission factors (EFs) of Hexamethylcyclotrisiloxane (D3), Octamethylcyclotrisiloxane (D4) and Decamethylcyclotrisiloxane (D5) were determined, and will be discussed with only specific types of vehicles emitting significant quantities of VMSs. Our results will also be compared to recent tunnel measurements, which demonstrated elevated concentrations of VMSs. Additionally, our results offer new insights into characterization and source appointment siloxanes in the atmosphere.Figure 1. Real-time concentrations of D3, D4, D5, acetone, benzene, toluene, and driving cycle for a) a gasoline engine and b) a diesel engine.
- 15 March 2025
- Published by Copernicus GmbH
Open AccessEmissions of Volatile Methyl Siloxanes (VMSs) from Vehicles
Volatile Methyl Siloxanes (VMSs) are anthropogenic molecules emitted from personal care products and industrial chemical products. Recent studies have found that concentrations of VMSs tend to be higher in densely populated urban areas, although research in large urban centers remains limited. Toxicity of such molecules remain uncertain with often conflicting reports. Previous literature has also reported the presence of long chain siloxanes in the particle phase from traffic emissions, and represented the first identification and quantification of siloxanes mostly likely emitted from vehicles.In this study, the chassis dynamometer measurements were conducted to characterize the gaseous components from a variety of vehicles, including gasoline passenger cars, diesel passenger cars, and scooters. Time-resolved volatile organic compound (VOC) emissions during the cold start through a full driving cycle from different vehicles were chemically characterized by the Vocus proton-transfer-reaction time-of-flight mass spectrometer (VOCUS PTR-TOF-MS). The emission factors (EFs) of Hexamethylcyclotrisiloxane (D3), Octamethylcyclotrisiloxane (D4) and Decamethylcyclotrisiloxane (D5) were determined, and will be discussed with only specific types of vehicles emitting significant quantities of VMSs. Our results will also be compared to recent tunnel measurements, which demonstrated elevated concentrations of VMSs. Additionally, our results offer new insights into characterization and source appointment siloxanes in the atmosphere.Figure 1. Real-time concentrations of D3, D4, D5, acetone, benzene, toluene, and driving cycle for a) a gasoline engine and b) a diesel engine.
- 9 April 2024
- Published by Elsevier in Atmospheric Environment
- Vol. 328
Molecular composition and sources of free amino acids in atmospheric aerosols from Mt. Tai and a nearby city
- 9 April 2024
- Published by Elsevier in Atmospheric Environment
- Vol. 328
Molecular composition and sources of free amino acids in atmospheric aerosols from Mt. Tai and a nearby city
- Open Access
- 11 October 2022
- Published by Springer Nature in npj Climate and Atmospheric Science
- Vol. 5 (1) , 1-13
Stable iron isotopic composition of atmospheric aerosols: An overview
Atmospheric particulate matter (PM) has a significant impact on both the natural environment and human health. Iron is one of the most abundant elements in the earth’s crust, playing an important role in geochemical processes, and is also an important trace component in atmospheric PM. In recent years, with the rapid development of non-traditional (metal) stable isotope technologies, new solutions and methods for the source apportionments of heavy metal elements have been put forward. Stable iron isotope analysis has become an effective tool to trace iron in atmospheric particles. This review paper briefly summarizes the recent progress of atmospheric iron isotope geochemistry. We show that some of the major natural and anthropogenic PM sources have different iron isotopic compositions. A Bayesian isotopic mixing model MixSIAR was used to quantitatively re-evaluate the contributions of different sources to iron in both urban and marine aerosols based on iron isotopic data in the literature. The results highlight the value of stable iron isotope analyses as an effective tool in the source apportionment of atmospheric aerosols.
- 11 October 2022
- Published by Springer Nature in npj Climate and Atmospheric Science
- Vol. 5 (1) , 1-13
Open AccessStable iron isotopic composition of atmospheric aerosols: An overview
Atmospheric particulate matter (PM) has a significant impact on both the natural environment and human health. Iron is one of the most abundant elements in the earth’s crust, playing an important role in geochemical processes, and is also an important trace component in atmospheric PM. In recent years, with the rapid development of non-traditional (metal) stable isotope technologies, new solutions and methods for the source apportionments of heavy metal elements have been put forward. Stable iron isotope analysis has become an effective tool to trace iron in atmospheric particles. This review paper briefly summarizes the recent progress of atmospheric iron isotope geochemistry. We show that some of the major natural and anthropogenic PM sources have different iron isotopic compositions. A Bayesian isotopic mixing model MixSIAR was used to quantitatively re-evaluate the contributions of different sources to iron in both urban and marine aerosols based on iron isotopic data in the literature. The results highlight the value of stable iron isotope analyses as an effective tool in the source apportionment of atmospheric aerosols.
- 10 July 2019
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 123 (31) , 19135-19141
Size-Dependent Thermodynamic Properties of Two Types of Phase Transitions of Nano-Bi2O3 and Their Differences
- 10 July 2019
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 123 (31) , 19135-19141
Size-Dependent Thermodynamic Properties of Two Types of Phase Transitions of Nano-Bi2O3 and Their Differences