Roshan Vijay Marode
Roshan Vijay Marode has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Srinivasa Rao Pedapati
College of Engineering & Sciences, The University of Texas Permian Basin, 11105 West Highway 191, Midland, TX 79707, USA
10 shared publications - Adeel Hassan
Department of Mechanical Engineering, Universiti Teknologi PETRONAS, Seri Iskandar 32610, Perak Darul Ridzuan, Malaysia
5 shared publications - Venkata Somi Reddy Janga
Department of Mechanical Engineering, Universiti Teknologi PETRONAS, Seri Iskandar 32610, Malaysia
3 shared publications - Khurram Altaf
Department of Mechanical Engineering, Universiti Teknologi PETRONAS, Seri Iskandar 32610, Perak Darul Ridzuan, Malaysia
2 shared publications Mokhtar Awang
2 shared publications- Mokhtar Awang
Universiti Teknologi PETRONAS
2 shared publications
Latest Publications
- Open Access
- 21 June 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (6) , 214
Challenges and Opportunities in Friction-Based Additive Manufacturing of Heat-Treatable Aluminum Alloys
Heat-treatable aluminum alloys are widely used in aerospace and automotive industries for high-performance structural applications. However, their processing through conventional fusion-based additive manufacturing is limited by solidification-related defects, such as hot cracking, porosity, and elemental segregation. To overcome these limitations, friction-based additive manufacturing (FBAM) has emerged as a promising solid-state alternative. FBAM primarily includes friction stir additive manufacturing (FSAM), additive friction stir deposition (AFSD), friction screw extrusion additive manufacturing (FSEAM), and friction rolling additive manufacturing (FRAM), which differ in feedstock form and process configuration. In these processes, feed material is consolidated through frictional heat generated below the melting temperature, enabling the formation of refined equiaxed microstructures while minimizing solidification defects. Despite these advantages, significant challenges persist in processing heat-treatable aluminum alloys, particularly the 2xxx, 6xxx, and 7xxx series. These include non-uniform microstructure and mechanical properties along the build direction; precipitation instability; process-induced defects, such as tunnel formation; and mechanical properties that are often inferior to those of the corresponding base materials (BMs). Reported FBAM builds generally exhibit equiaxed ultrafine grains below 1 μm; however, the strength and microhardness of heat-treated alloy builds commonly remain around 70–75% of the corresponding BM. Following post-heat treatment, microhardness can be nearly fully recovered, whereas UTS typically reaches about 80–85% of BMs, often with an associated ductility reduction of nearly 50%. This review critically analyzes research reported over the past decade on FBAM processing of heat-treatable aluminum alloys, covering FSAM, AFSD, FSEAM, and FRAM. The key challenges related to microstructural evolution and mechanical performance are systematically discussed for each alloy series. Furthermore, mitigation strategies proposed in the literature, including process parameter optimization, in-process cooling, post-heat treatment, and nanoparticle reinforcement (e.g., SiC, TiC, Ni and ZrO2), are evaluated. Finally, existing research gaps are identified, and future directions are proposed to support the development of robust, scalable, and high-performance FBAM processes for heat-treatable aluminum alloys.
- 21 June 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (6) , 214
Open AccessChallenges and Opportunities in Friction-Based Additive Manufacturing of Heat-Treatable Aluminum Alloys
Heat-treatable aluminum alloys are widely used in aerospace and automotive industries for high-performance structural applications. However, their processing through conventional fusion-based additive manufacturing is limited by solidification-related defects, such as hot cracking, porosity, and elemental segregation. To overcome these limitations, friction-based additive manufacturing (FBAM) has emerged as a promising solid-state alternative. FBAM primarily includes friction stir additive manufacturing (FSAM), additive friction stir deposition (AFSD), friction screw extrusion additive manufacturing (FSEAM), and friction rolling additive manufacturing (FRAM), which differ in feedstock form and process configuration. In these processes, feed material is consolidated through frictional heat generated below the melting temperature, enabling the formation of refined equiaxed microstructures while minimizing solidification defects. Despite these advantages, significant challenges persist in processing heat-treatable aluminum alloys, particularly the 2xxx, 6xxx, and 7xxx series. These include non-uniform microstructure and mechanical properties along the build direction; precipitation instability; process-induced defects, such as tunnel formation; and mechanical properties that are often inferior to those of the corresponding base materials (BMs). Reported FBAM builds generally exhibit equiaxed ultrafine grains below 1 μm; however, the strength and microhardness of heat-treated alloy builds commonly remain around 70–75% of the corresponding BM. Following post-heat treatment, microhardness can be nearly fully recovered, whereas UTS typically reaches about 80–85% of BMs, often with an associated ductility reduction of nearly 50%. This review critically analyzes research reported over the past decade on FBAM processing of heat-treatable aluminum alloys, covering FSAM, AFSD, FSEAM, and FRAM. The key challenges related to microstructural evolution and mechanical performance are systematically discussed for each alloy series. Furthermore, mitigation strategies proposed in the literature, including process parameter optimization, in-process cooling, post-heat treatment, and nanoparticle reinforcement (e.g., SiC, TiC, Ni and ZrO2), are evaluated. Finally, existing research gaps are identified, and future directions are proposed to support the development of robust, scalable, and high-performance FBAM processes for heat-treatable aluminum alloys.
- Open Access
- 8 April 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (4) , 200
Microstructural, Thermal, and Mechanical Characterization of TPU Composites Using Hybrid MWCNT–Graphene Nanofiller for Thermal Management
Advanced thermal management applications, including electronics cooling, battery systems, and micro heat exchangers, are increasingly requiring thermally conductive yet flexible polymer composites. Composite films containing total nanofiller loadings of 2.5, 5, 7.5, and 10 wt.% were systematically characterized using SEM, TGA, DSC, TT, and SSTM following ASTM C177-19. SEM analysis confirmed uniform dispersion and effective network formation of MWCNTs and GNPs within the TPU matrix at higher filler loadings. Thermal stability improved significantly, with the degradation onset temperature increasing from 319.2 °C for pure TPU to 369 °C for the TPU/MWCNT/GNP (90/5/5 wt.%) composite. DSC results revealed enhanced glass transition and melting temperatures, indicating improved thermal resistance and crystallinity. Mechanical testing showed a substantial increase in Young’s modulus, reaching 72.5 MPa for the 90/5/5 wt.% composite, corresponding to a 286.66% improvement over pure TPU. Most notably, steady-state thermal conductivity increased dramatically from 0.20 W/mK for pure TPU to 1.533 W/mK for the 90/5/5 wt.% composite, representing a 666.50% enhancement. The experimental results closely aligned with percolation-based theoretical models at higher filler concentrations. Overall, the developed hybrid nanofiller TPU composites demonstrate a synergistic improvement in thermal conductivity, mechanical strength, and thermal stability, making them promising candidates for flexible thermal management components in electronics, automotive, renewable energy, and biomedical applications.
- 8 April 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (4) , 200
Open AccessMicrostructural, Thermal, and Mechanical Characterization of TPU Composites Using Hybrid MWCNT–Graphene Nanofiller for Thermal Management
Advanced thermal management applications, including electronics cooling, battery systems, and micro heat exchangers, are increasingly requiring thermally conductive yet flexible polymer composites. Composite films containing total nanofiller loadings of 2.5, 5, 7.5, and 10 wt.% were systematically characterized using SEM, TGA, DSC, TT, and SSTM following ASTM C177-19. SEM analysis confirmed uniform dispersion and effective network formation of MWCNTs and GNPs within the TPU matrix at higher filler loadings. Thermal stability improved significantly, with the degradation onset temperature increasing from 319.2 °C for pure TPU to 369 °C for the TPU/MWCNT/GNP (90/5/5 wt.%) composite. DSC results revealed enhanced glass transition and melting temperatures, indicating improved thermal resistance and crystallinity. Mechanical testing showed a substantial increase in Young’s modulus, reaching 72.5 MPa for the 90/5/5 wt.% composite, corresponding to a 286.66% improvement over pure TPU. Most notably, steady-state thermal conductivity increased dramatically from 0.20 W/mK for pure TPU to 1.533 W/mK for the 90/5/5 wt.% composite, representing a 666.50% enhancement. The experimental results closely aligned with percolation-based theoretical models at higher filler concentrations. Overall, the developed hybrid nanofiller TPU composites demonstrate a synergistic improvement in thermal conductivity, mechanical strength, and thermal stability, making them promising candidates for flexible thermal management components in electronics, automotive, renewable energy, and biomedical applications.
- Open Access
- 16 October 2025
- Published by MDPI AG in Lubricants
- Vol. 13 (10) , 450
Investigation of Thermo-Mechanical Characteristics in Friction Stir Processing of AZ91 Surface Composite: Novel Study Through SPH Analysis
The current study examines the influence of tool rotational speed (TRS) and reinforcement volume fraction (%vol.) of SiC on particle distribution in the stir zone (SZ) of AZ91 Mg alloy. Two parameter sets were analyzed: S1 (500 rpm TRS, 13% vol.) and S2 (1500 rpm TRS, 10% vol.), with a constant tool traverse speed (TTS) of 60 mm/min. SPH simulations revealed that in S1, lower TRS resulted in limited SiC displacement, leading to significant agglomeration zones, particularly along the advancing side (AS) and beneath the tool pin. Cross-sectional observations at 15 mm and 20 mm from the plunging phase indicated the formation of reinforcement clusters along the tool path, with inadequate SiC transference to the retreating side (RS). The reduced stirring force in S1 caused poor reinforcement dispersion, with most SiC nodes settling at the SZ bottom due to insufficient upward movement. In contrast, S2 demonstrated enhanced particle mobility due to higher TRS, improving reinforcement homogeneity. Intense stirring facilitated lateral and upward SiC movement, forming an interconnected reinforcement network. SPH nodes exhibited improved dispersion, with particles across the SZ and more evenly deposited on the RS. A comparative assessment of experimental and simulated reinforcement distributions confirmed a strong correlation. Results highlight the pivotal role of TRS in reinforcement movement and agglomeration control. Higher TRS enhances stirring and promotes uniform SiC dispersion, whereas an excessive reinforcement fraction increases matrix viscosity and restricts particle mobility. Thus, optimizing TRS and reinforcement content through numerical analysis using SPH is essential for producing a homogeneous, well-reinforced composite layer with improved surface properties. The findings of this study have significant practical applications, particularly in industrial material selection, improving manufacturing processes, and developing more efficient surface composites, thereby enhancing the overall performance and reliability of Mg alloys in engineering applications.
- 16 October 2025
- Published by MDPI AG in Lubricants
- Vol. 13 (10) , 450
Open AccessInvestigation of Thermo-Mechanical Characteristics in Friction Stir Processing of AZ91 Surface Composite: Novel Study Through SPH Analysis
The current study examines the influence of tool rotational speed (TRS) and reinforcement volume fraction (%vol.) of SiC on particle distribution in the stir zone (SZ) of AZ91 Mg alloy. Two parameter sets were analyzed: S1 (500 rpm TRS, 13% vol.) and S2 (1500 rpm TRS, 10% vol.), with a constant tool traverse speed (TTS) of 60 mm/min. SPH simulations revealed that in S1, lower TRS resulted in limited SiC displacement, leading to significant agglomeration zones, particularly along the advancing side (AS) and beneath the tool pin. Cross-sectional observations at 15 mm and 20 mm from the plunging phase indicated the formation of reinforcement clusters along the tool path, with inadequate SiC transference to the retreating side (RS). The reduced stirring force in S1 caused poor reinforcement dispersion, with most SiC nodes settling at the SZ bottom due to insufficient upward movement. In contrast, S2 demonstrated enhanced particle mobility due to higher TRS, improving reinforcement homogeneity. Intense stirring facilitated lateral and upward SiC movement, forming an interconnected reinforcement network. SPH nodes exhibited improved dispersion, with particles across the SZ and more evenly deposited on the RS. A comparative assessment of experimental and simulated reinforcement distributions confirmed a strong correlation. Results highlight the pivotal role of TRS in reinforcement movement and agglomeration control. Higher TRS enhances stirring and promotes uniform SiC dispersion, whereas an excessive reinforcement fraction increases matrix viscosity and restricts particle mobility. Thus, optimizing TRS and reinforcement content through numerical analysis using SPH is essential for producing a homogeneous, well-reinforced composite layer with improved surface properties. The findings of this study have significant practical applications, particularly in industrial material selection, improving manufacturing processes, and developing more efficient surface composites, thereby enhancing the overall performance and reliability of Mg alloys in engineering applications.
- Open Access
- 15 October 2025
- Published by MDPI AG in Journal of Composites Science
- Vol. 9 (10) , 568
Development of Carbide-Reinforced Al-7075 Multi-Layered Composites via Friction Stir Additive Manufacturing
Friction stir additive manufacturing (FSAM) is a promising solid-state technique for fabricating high-strength aluminum alloys, such as Al-7075, which are difficult to process using conventional melting-based additive manufacturing (AM) methods. This study investigates the mechanical properties and tool wear behavior of seven-layered Al-7075 multi-layered composites reinforced with silicon carbide (SiC) and titanium carbide (TiC) fabricated via FSAM. Microstructural analysis confirmed defect-free multi-layered composites with a homogeneous distribution of SiC and TiC reinforcements in the nugget zone (NZ), although particle agglomeration was observed at the bottom of the pin-driven zone (PDZ). The TiC-reinforced composite exhibited finer grains than the SiC-reinforced composite in both as-welded and post-weld heat-treated (PWHT) conditions, achieving a minimum grain size of 1.25 µm, corresponding to a 95% reduction compared to the base metal. The TiC-reinforced multi-layered composite demonstrated superior mechanical properties, attaining a microhardness of 93.7 HV and a UTS of 263.02 MPa in the as-welded condition, compared to 88.6 HV and 236.34 MPa for the SiC-reinforced composite. After PWHT, the TiC-reinforced composite further improved to 159.12 HV and 313.46 MPa UTS, along with a higher elongation of 11.14% compared to 7.5% for the SiC-reinforced composite. Tool wear analysis revealed that SiC reinforcement led to greater tool degradation, resulting in a 1.17% weight loss. These findings highlight the advantages of TiC reinforcement in FSAM, offering enhanced mechanical performance with reduced tool wear in multi-layered Al-7075 composites.
- 15 October 2025
- Published by MDPI AG in Journal of Composites Science
- Vol. 9 (10) , 568
Open AccessDevelopment of Carbide-Reinforced Al-7075 Multi-Layered Composites via Friction Stir Additive Manufacturing
Friction stir additive manufacturing (FSAM) is a promising solid-state technique for fabricating high-strength aluminum alloys, such as Al-7075, which are difficult to process using conventional melting-based additive manufacturing (AM) methods. This study investigates the mechanical properties and tool wear behavior of seven-layered Al-7075 multi-layered composites reinforced with silicon carbide (SiC) and titanium carbide (TiC) fabricated via FSAM. Microstructural analysis confirmed defect-free multi-layered composites with a homogeneous distribution of SiC and TiC reinforcements in the nugget zone (NZ), although particle agglomeration was observed at the bottom of the pin-driven zone (PDZ). The TiC-reinforced composite exhibited finer grains than the SiC-reinforced composite in both as-welded and post-weld heat-treated (PWHT) conditions, achieving a minimum grain size of 1.25 µm, corresponding to a 95% reduction compared to the base metal. The TiC-reinforced multi-layered composite demonstrated superior mechanical properties, attaining a microhardness of 93.7 HV and a UTS of 263.02 MPa in the as-welded condition, compared to 88.6 HV and 236.34 MPa for the SiC-reinforced composite. After PWHT, the TiC-reinforced composite further improved to 159.12 HV and 313.46 MPa UTS, along with a higher elongation of 11.14% compared to 7.5% for the SiC-reinforced composite. Tool wear analysis revealed that SiC reinforcement led to greater tool degradation, resulting in a 1.17% weight loss. These findings highlight the advantages of TiC reinforcement in FSAM, offering enhanced mechanical performance with reduced tool wear in multi-layered Al-7075 composites.
- Top Cited PapersOpen Access
- 1 June 2024
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 12 (6) , 2091-2146
Research progress in friction stir processing of magnesium alloys and their metal matrix surface composites: Evolution in the 21st century
- 1 June 2024
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 12 (6) , 2091-2146
Top Cited PapersOpen AccessResearch progress in friction stir processing of magnesium alloys and their metal matrix surface composites: Evolution in the 21st century
- Open Access
Computational Modelling and Comparative Analysis of Friction Stir Welding and Stationary Shoulder Friction Stir Welding on AA6061
This research focuses on the computational modelling and comparative analysis of friction stir welding (FSW) and stationary shoulder friction stir welding (SSFSW) applied to AA6061-T6 aluminium alloy. SSFSW, an FSW variant, employs a stationary shoulder and a rotating pin. This study introduces a numerical model for both processes, using the innovative Smoothed Particle Hydrodynamics (SPH) technique to capture their distinct thermo-mechanical characteristics. The aim is to unravel its mechanics and multi-physics in SSFSW and compare it with conventional FSW. The temperatures predicted by the model exhibited a close agreement between the advancing side (AS) and retreating side (RS). Plastic strain patterns show that regular FSW is different from SSFSW. In SSFSW, the strain is less, and the plastic area is comparatively slightly narrower. The distinct “ironing effect” resulting from the stationary shoulder in SSFSW reduces the heat-affected zone (HAZ). Yet, it maintains efficient plasticisation and material flow within the pin-affected zone (PAZ). This research emphasises the significant impact of temperature, strain, material flow, and thermo-mechanical characteristics on the quality of joints. Future suggestions include exploring process parameters more broadly, examining dissimilar welding techniques and hybrid approaches, and comprehensively investigating the diverse effects of SSFSW under various configurations and joint angles.
Open AccessComputational Modelling and Comparative Analysis of Friction Stir Welding and Stationary Shoulder Friction Stir Welding on AA6061
This research focuses on the computational modelling and comparative analysis of friction stir welding (FSW) and stationary shoulder friction stir welding (SSFSW) applied to AA6061-T6 aluminium alloy. SSFSW, an FSW variant, employs a stationary shoulder and a rotating pin. This study introduces a numerical model for both processes, using the innovative Smoothed Particle Hydrodynamics (SPH) technique to capture their distinct thermo-mechanical characteristics. The aim is to unravel its mechanics and multi-physics in SSFSW and compare it with conventional FSW. The temperatures predicted by the model exhibited a close agreement between the advancing side (AS) and retreating side (RS). Plastic strain patterns show that regular FSW is different from SSFSW. In SSFSW, the strain is less, and the plastic area is comparatively slightly narrower. The distinct “ironing effect” resulting from the stationary shoulder in SSFSW reduces the heat-affected zone (HAZ). Yet, it maintains efficient plasticisation and material flow within the pin-affected zone (PAZ). This research emphasises the significant impact of temperature, strain, material flow, and thermo-mechanical characteristics on the quality of joints. Future suggestions include exploring process parameters more broadly, examining dissimilar welding techniques and hybrid approaches, and comprehensively investigating the diverse effects of SSFSW under various configurations and joint angles.
- 31 July 2023
- Published by Springer Nature
- p. 35-46
Friction Stir Processing of Magnesium Metal Matrix Composites: A Review
- 31 July 2023
- Published by Springer Nature
- p. 35-46
Friction Stir Processing of Magnesium Metal Matrix Composites: A Review
- 28 May 2023
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 23 (3) , 1-33
A review on numerical modelling techniques in friction stir processing: current and future perspective
- 28 May 2023
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 23 (3) , 1-33
A review on numerical modelling techniques in friction stir processing: current and future perspective
- 2 May 2023
- Published by Elsevier in Materials Today: Proceedings
- Vol. 109, 12-21
Investigation on AA7075 and AA7075/SiC surface composites using friction stir processing: An experimental and numerical approach
- 2 May 2023
- Published by Elsevier in Materials Today: Proceedings
- Vol. 109, 12-21
Investigation on AA7075 and AA7075/SiC surface composites using friction stir processing: An experimental and numerical approach