Miaozi Zheng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Miaozi Zheng has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Menglan Duan
Institute for Ocean Engineering, Tsinghua Shenzhen International Graduate School, Tsinghua University, Shenzhen, China
5 shared publications - Li Zhang
Southern Marine Science and Engineering Guangdong Laboratory (Zhanjiang)
3 shared publications - Yulong Zhang
Institute of Acoustics, Chinese Academy of Sciences, Beijing 100190, China
3 shared publications - Chaofei Zhang
College of Safety and Ocean Engineering, China University of Petroleum, Beijing 102249, China
2 shared publications Jia Dang
State Key Laboratory of Marine Resource Utilization in South China Sea, Hainan University, Hainan, China
2 shared publications- Jian Tan
College of Safety and Ocean Engineering, China University of Petroleum-Beijing, Beijing 102249, China
2 shared publications
Latest Publications
- 14 October 2024
- Published by Elsevier in Ocean Engineering
- Vol. 313
Comprehensive investigation on safety and integrity evaluation of offshore platform piles invested by shallow gas in water-saturated soil
- 14 October 2024
- Published by Elsevier in Ocean Engineering
- Vol. 313
Comprehensive investigation on safety and integrity evaluation of offshore platform piles invested by shallow gas in water-saturated soil
- Open Access
- 14 September 2023
- Published by Springer Nature in Advanced Composites and Hybrid Materials
- Vol. 6 (5) , 1-15
High thermal storage polyurethane composite embedded with microencapsulated phase change materials and analysis of its unsteady heat transfer
- 14 September 2023
- Published by Springer Nature in Advanced Composites and Hybrid Materials
- Vol. 6 (5) , 1-15
Open AccessHigh thermal storage polyurethane composite embedded with microencapsulated phase change materials and analysis of its unsteady heat transfer
- Open Access
Investigation of Dynamic Behavior of Ultra-Large Cold-Water Pipes for Ocean Thermal Energy Conversion
Ocean Thermal Energy Conversion (OTEC) is a process that can produce electricity by utilizing the temperature difference between deep cold water and surface warm water. The cold-water pipe (CWP) is a key component of OTEC systems, which transports deep cold water to the floating platform. The CWP is subjected to various environmental and operational loads, such as waves, currents, internal flow, and platform motion, which can affect its dynamic response and stability. In this paper, we establish a computational model of the mechanical performance of the CWP based on the Euler–Bernoulli beam theory and the Morrison equation, considering the effects of internal flow, sea current, and wave excitation. We use the differential quadrature method (DQM) to obtain a semi-analytical solution of the lateral displacement and bending moment of the CWP. We verify the correctness and validity of our model by comparing it with the finite element simulation results using OrcaFlex software. We also analyze the effects of operating conditions—such as wave intensity, clump weight at the bottom, and internal flow velocity—on the dynamic response of the CWP using numerical simulation and the orthogonal experimental method. The results show that changing the wave strength and internal flow velocity has little effect on the lateral displacement of the CWP but increasing the current velocity can significantly increase the lateral displacement of the CWP, which can lead to instability. The effects of waves, clump weight, internal flow, and sea current on the maximum bending moment of the CWP are similar; all of them increase sharply at first and then decrease gradually until they level off. The differences in the effects are mainly reflected in the different locations of the pipe sections. This paper suggests some design guidance for CWP in terms of dynamic responses depending on the operating conditions. This paper contributes to the journal’s scope by providing a novel and efficient method for analyzing the mechanical performance of CWP for OTEC systems, which is an important ocean energy resource.
Open AccessInvestigation of Dynamic Behavior of Ultra-Large Cold-Water Pipes for Ocean Thermal Energy Conversion
Ocean Thermal Energy Conversion (OTEC) is a process that can produce electricity by utilizing the temperature difference between deep cold water and surface warm water. The cold-water pipe (CWP) is a key component of OTEC systems, which transports deep cold water to the floating platform. The CWP is subjected to various environmental and operational loads, such as waves, currents, internal flow, and platform motion, which can affect its dynamic response and stability. In this paper, we establish a computational model of the mechanical performance of the CWP based on the Euler–Bernoulli beam theory and the Morrison equation, considering the effects of internal flow, sea current, and wave excitation. We use the differential quadrature method (DQM) to obtain a semi-analytical solution of the lateral displacement and bending moment of the CWP. We verify the correctness and validity of our model by comparing it with the finite element simulation results using OrcaFlex software. We also analyze the effects of operating conditions—such as wave intensity, clump weight at the bottom, and internal flow velocity—on the dynamic response of the CWP using numerical simulation and the orthogonal experimental method. The results show that changing the wave strength and internal flow velocity has little effect on the lateral displacement of the CWP but increasing the current velocity can significantly increase the lateral displacement of the CWP, which can lead to instability. The effects of waves, clump weight, internal flow, and sea current on the maximum bending moment of the CWP are similar; all of them increase sharply at first and then decrease gradually until they level off. The differences in the effects are mainly reflected in the different locations of the pipe sections. This paper suggests some design guidance for CWP in terms of dynamic responses depending on the operating conditions. This paper contributes to the journal’s scope by providing a novel and efficient method for analyzing the mechanical performance of CWP for OTEC systems, which is an important ocean energy resource.
- Open Access
- 30 July 2023
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 11 (8) , 1520
Effects of Laying Depth and Pipe Arc Length on the Mechanical Performance of Large-Diameter Cold-Water Pipes during Float-and-Sink Installation
The successful operation of a large-diameter cold water pipeline installation is crucial for harnessing the potential of ocean thermal energy conversion. However, there is a shortage of research focused on mechanical performance analysis during installation. This study establishes a pipeline response analysis model based on a nonlinear beam theory to elucidate the underlying mechanical behaviour. Employing the method of singular perturbation, the general solution for the exterior region of the pipeline, the solution at the boundary layer, and the valid solution across the entire domain are derived. A comparison with numerical solutions is conducted to validate the accuracy and effectiveness of the theoretical model. Based on the theoretical analysis, the influence of installation depth and pipeline curvature on the pipeline’s shape, tension, curvature, and stress is discussed. The results indicate that increasing the installation depth leads to intensified pipeline bending and significant deformation, reaching a maximum bending moment of 3.92 MN∙m at a distance of 50~100 m from the bottom of the pipeline. The results also show that, as the pipeline’s arc length increases from 0 to 100 m, the bending curvature, Von Mises stress, and bending stress exhibit a trend of initial growth followed by a decline, peaking at 7.45 MPa, and 6.83 Mpa, respectively, while the actual tension and axial tension decrease initially and then increase, reaching −0.17 MN and −0.17 MPa, respectively, at the maximum arc length. The findings of this study provide valuable insights for practical cold-water pipe installation and laying.
- 30 July 2023
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 11 (8) , 1520
Open AccessEffects of Laying Depth and Pipe Arc Length on the Mechanical Performance of Large-Diameter Cold-Water Pipes during Float-and-Sink Installation
The successful operation of a large-diameter cold water pipeline installation is crucial for harnessing the potential of ocean thermal energy conversion. However, there is a shortage of research focused on mechanical performance analysis during installation. This study establishes a pipeline response analysis model based on a nonlinear beam theory to elucidate the underlying mechanical behaviour. Employing the method of singular perturbation, the general solution for the exterior region of the pipeline, the solution at the boundary layer, and the valid solution across the entire domain are derived. A comparison with numerical solutions is conducted to validate the accuracy and effectiveness of the theoretical model. Based on the theoretical analysis, the influence of installation depth and pipeline curvature on the pipeline’s shape, tension, curvature, and stress is discussed. The results indicate that increasing the installation depth leads to intensified pipeline bending and significant deformation, reaching a maximum bending moment of 3.92 MN∙m at a distance of 50~100 m from the bottom of the pipeline. The results also show that, as the pipeline’s arc length increases from 0 to 100 m, the bending curvature, Von Mises stress, and bending stress exhibit a trend of initial growth followed by a decline, peaking at 7.45 MPa, and 6.83 Mpa, respectively, while the actual tension and axial tension decrease initially and then increase, reaching −0.17 MN and −0.17 MPa, respectively, at the maximum arc length. The findings of this study provide valuable insights for practical cold-water pipe installation and laying.
- Open Access
- 19 June 2023
- Published by MDPI AG in Preprints.org
Investigation on Dynamic Behavior of Ultra-Large Cold-water Pipe for Ocean Thermal Energy Conversion
Ultra-large cold-water pipes (CWP) may present structural instability phenomenon under complex and variable operating conditions, and the current theoretical analysis rarely takes into account the influence of multiple key parameters at the same time, resulting in some errors between the prediction results and the actual deformation behavior of the pipe. Considering this issue, this paper establishes a computational analysis model of the mechanical performance of the CWP based on the Euler-Bernoulli beam theory, considering the effect of waves, the clump weight at the bottom, internal flow and sea current, and gives a time-dependent solution of the mechanical response of the pipe with the action of multiple key parameters using the differential quadrature method (DQM). Additionally, the correctness and validity of the theoretical model are well verified by comparing the numerical solution with the theoretical results. Finally, to study the effects of operating conditions on the mechanical response of the pipe, the effects of waves, the clump weight, internal flow and sea current on the lateral deflection and maximum bending moment of the pipeline are discussed based on numerical simulation and orthogonal experimental method. The results show that changing the wave strength and internal flow velocity has little effect on the lateral deflection of the CWP, and the clump weight at the bottom can effectively suppress the lateral deflection of the pipeline, but increasing the current velocity can significantly increase the lateral deflection of the pipeline, which can lead to the instability of the pipe. Nevertheless, the effects of waves, the clump weight, internal flow and sea current on the maximum bending moment of the pipeline are basically the same, all of them increase sharply at first, and then decrease gradually until they level off, and the differences in the effects are mainly reflected in the different locations of the pipe sections. This paper suggests the design guidance of CWP in aspect of dynamic response depending on the operating condition.
- 19 June 2023
- Published by MDPI AG in Preprints.org
Open AccessInvestigation on Dynamic Behavior of Ultra-Large Cold-water Pipe for Ocean Thermal Energy Conversion
Ultra-large cold-water pipes (CWP) may present structural instability phenomenon under complex and variable operating conditions, and the current theoretical analysis rarely takes into account the influence of multiple key parameters at the same time, resulting in some errors between the prediction results and the actual deformation behavior of the pipe. Considering this issue, this paper establishes a computational analysis model of the mechanical performance of the CWP based on the Euler-Bernoulli beam theory, considering the effect of waves, the clump weight at the bottom, internal flow and sea current, and gives a time-dependent solution of the mechanical response of the pipe with the action of multiple key parameters using the differential quadrature method (DQM). Additionally, the correctness and validity of the theoretical model are well verified by comparing the numerical solution with the theoretical results. Finally, to study the effects of operating conditions on the mechanical response of the pipe, the effects of waves, the clump weight, internal flow and sea current on the lateral deflection and maximum bending moment of the pipeline are discussed based on numerical simulation and orthogonal experimental method. The results show that changing the wave strength and internal flow velocity has little effect on the lateral deflection of the CWP, and the clump weight at the bottom can effectively suppress the lateral deflection of the pipeline, but increasing the current velocity can significantly increase the lateral deflection of the pipeline, which can lead to the instability of the pipe. Nevertheless, the effects of waves, the clump weight, internal flow and sea current on the maximum bending moment of the pipeline are basically the same, all of them increase sharply at first, and then decrease gradually until they level off, and the differences in the effects are mainly reflected in the different locations of the pipe sections. This paper suggests the design guidance of CWP in aspect of dynamic response depending on the operating condition.
- Open Access
- 18 May 2023
- Published by Springer Nature in Research Square
Development of a high-thermal-storage composite material embedded with PCM microcapsules and analysis of its unsteady heat transfer process
Phase-change insulation materials can effectively extend the holding time of submarine oil and gas pipelines. Shape-stable phase-change composites have good application prospects owing to their chemical stability and leakage resistance. In this study, a microencapsulated phase-change material (MPCM)-embedded polyurethane (PU) composite (PU–MPCM) was prepared as an insulation material for subsea pipelines. The unsteady heat transfer process of the PU–MPCM composite was simulated using COMSOL Multiphysics, and an insulation experiment was conducted on this composite. PU–MPCM exhibited a high thermal storage performance and favorable shape stability. The relative effective enthalpy coefficients of PU–MPCM composites with different MPCM contents were greater than 80%. The maximum MPCM content in the PU–MPCM composite was 24 wt% (PU–MPCM24). The melting enthalpy of PU–MPCM24 reached 35.95 J/g, and its effective thermal conductivity was as low as 0.16 W/(m∙K). The holding time of PU–MPCM24 could be increased by 229.79% compared with that of pure PU. The PU–MPCM composite exhibited good mechanical properties and low water absorption, making it suitable for underwater environments. Owing to its low-cost preparation process and excellent thermal properties, PU–MPCM24 can be considered a potential insulation material for practical applications in subsea pipelines.
- 18 May 2023
- Published by Springer Nature in Research Square
Open AccessDevelopment of a high-thermal-storage composite material embedded with PCM microcapsules and analysis of its unsteady heat transfer process
Phase-change insulation materials can effectively extend the holding time of submarine oil and gas pipelines. Shape-stable phase-change composites have good application prospects owing to their chemical stability and leakage resistance. In this study, a microencapsulated phase-change material (MPCM)-embedded polyurethane (PU) composite (PU–MPCM) was prepared as an insulation material for subsea pipelines. The unsteady heat transfer process of the PU–MPCM composite was simulated using COMSOL Multiphysics, and an insulation experiment was conducted on this composite. PU–MPCM exhibited a high thermal storage performance and favorable shape stability. The relative effective enthalpy coefficients of PU–MPCM composites with different MPCM contents were greater than 80%. The maximum MPCM content in the PU–MPCM composite was 24 wt% (PU–MPCM24). The melting enthalpy of PU–MPCM24 reached 35.95 J/g, and its effective thermal conductivity was as low as 0.16 W/(m∙K). The holding time of PU–MPCM24 could be increased by 229.79% compared with that of pure PU. The PU–MPCM composite exhibited good mechanical properties and low water absorption, making it suitable for underwater environments. Owing to its low-cost preparation process and excellent thermal properties, PU–MPCM24 can be considered a potential insulation material for practical applications in subsea pipelines.
- Open Access
- 18 October 2022
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 10 (10) , 1524
An Interface Parametric Evaluation on Wellbore Integrity during Natural Gas Hydrate Production
Based on the whole life cycle process of the economic exploitation of natural gas hydrate, this paper proposes the basic problem of stabilizing the wellbore for the basic conditions that must be met to ensure the integrity of the wellbore for exploitation: revealing the complex mechanism of fluid–solid–heat coupling in the process of the physical exchange of equilibrium among gas, water, and multiphase sand flows in the wellbore, hydrate reservoir, and wellbore, defining the interface conditions to ensure wellbore stability during the entire life cycle of hydrate production and proposing a scientific evaluation system of interface parameters for wellbore integrity.
- 18 October 2022
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 10 (10) , 1524
Open AccessAn Interface Parametric Evaluation on Wellbore Integrity during Natural Gas Hydrate Production
Based on the whole life cycle process of the economic exploitation of natural gas hydrate, this paper proposes the basic problem of stabilizing the wellbore for the basic conditions that must be met to ensure the integrity of the wellbore for exploitation: revealing the complex mechanism of fluid–solid–heat coupling in the process of the physical exchange of equilibrium among gas, water, and multiphase sand flows in the wellbore, hydrate reservoir, and wellbore, defining the interface conditions to ensure wellbore stability during the entire life cycle of hydrate production and proposing a scientific evaluation system of interface parameters for wellbore integrity.