PCPreeyaporn Chaiyasat

Preeyaporn Chaiyasat

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Preeyaporn Chaiyasat has a total of 65 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Biobased Polymer Microcapsules with Controlled PCM Retention and Cu2O Surface Functionalization for Thermal and Environmental Applications

    by Pobporn Promchan, Perapat Posayaanuwat, Khaydar Ergashovich Yunusov, Paiboon Sreearunothai, Preeyaporn Chaiyasat, Amorn Chaiyasat

    Biobased polymer microcapsules combining thermal energy storage and surface reactivity are of interest for advanced coating applications. In this work, microcapsules encapsulating capric acid (CA) were prepared via suspension polymerization using cinnamyl methacrylate (CMA)-based copolymers. The effects of polymer composition on particle formation, morphology, and encapsulation behavior were examined. Formulations containing methyl methacrylate (MMA) or ethylene glycol dimethacrylate (EGDMA) produced spherical microcapsules with improved suspension stability, whereas CMA/MAA-rich systems led to particle coagulation. The CA-loaded microcapsules exhibited latent heat storage behavior, confirming effective encapsulation of the phase-change material (PCM). To introduce additional functionality, Cu2O was deposited onto the microcapsule surface, yielding hybrid microcapsules with retained morphology and visible-light photocatalytic activity. Prior to Cu2O deposition, thermogravimetric analysis indicated CA loadings of approximately 43–47 wt %. The retention of encapsulated CA during Cu2O deposition strongly depended on the polymer network structure and deposition conditions. Under mild deposition conditions (∼30 °C), cross-linked P(CMA-EGDMA-MAA)/CA microcapsules maintained relatively high PCM loading values, indicating improved structural stability and preservation of phase-change functionality after Cu2O surface modification. The hybrid microcapsules achieved approximately 85% methylene blue removal within 300 min under visible-light irradiation. These results demonstrate that polymer composition influences encapsulation stability, while Cu2O surface deposition imparts photocatalytic functionality. The developed biobased microcapsules show potential for thermal regulation and self-cleaning coating applications.

  • Open Access

    Photoactive barium titanate-encapsulated polymer microcapsules for infrared-reflective coatings

    by Akira Sangchalee, Jittipat Omsinsombon, Amorn Chaiyasat, Preeyaporn Chaiyasat

  • Open Access

    Magnetic Alginate-Based Composite Beads Incorporating Cu/TiO 2 : Synthesis, Structure–Property Relationships, and Catalytic Applicability

    by Supanit Chungyampin, Kathawut Rawangkay, Kulwadee Ponanunrirk, Nattawut Rodtuk, Wissanu Charerntanom, Sasiradee Jantasee, Paiboon Sreearunothai, Preeyaporn Chaiyasat, Amorn Chaiyasat

    Magnetic alginate-based composite beads integrating Cu/TiO2 and magnetite (Fe3O4) were fabricated as polymer–inorganic hybrid systems for magnetic recovery. These composite beads were generated via ionotropic gelation, a method that enabled efficient encapsulation of inorganic constituents within the sodium alginate matrix while preserving the crystalline structures of Fe3O4 and anatase TiO2. The impact of Fe3O4 loading on the beads’ structural and physicochemical attributes was systematically investigated, revealing specific structure–property relationships that dictated encapsulation efficacy, swelling behavior, bulk density, and internal morphology. Among the formulations examined, the S-1.0Fe3O4–SA beads demonstrated a favorable balance between structural integrity and mass-transfer accessibility. The efficacy of the composite beads was evaluated via their employment in the hydrogenation of glacial acetic acid, a representative liquid-phase reaction. Examination of the reaction products indicated the formation of ethanol and ethyl acetate; the precise product distribution depended on the Cu loading in the Cu/TiO2 component. A moderate Cu content was observed to facilitate product formation, concurrently maintaining the structural stability of the beads. The S-1.0Fe3O4/SA-1.8Cu/TiO2-0.4 catalyst exhibited the highest ethanol production (18.69 mg L–1). Lower Cu loading resulted in insufficient active sites, whereas higher loading led to aggregation and reduced catalytic efficiency. Recycling tests revealed a gradual decrease in ethanol formation upon reuse, indicating partial catalyst deactivation, likely due to surface fouling and Cu leaching. Therefore, this study highlights the promise of alginate-based magnetic composite beads as a versatile polymer-supported platform, in which the macromolecular structure is crucial for dictating functional performance.


  • Open Access

    Highly Efficient NIR-Reflective CrAl 2 O 4 -Based Polymer Microcapsules for Advanced Thermal Management Coatings

    by Jittipat Omsinsombon, Amorn Chaiyasat, Chumphol Busabok, Preeyaporn Chaiyasat

    Near-infrared (NIR)-reflective materials are of interest for reducing solar heat gain in coated surfaces. In this study, CrAl2O4 particles were investigated as a novel NIR-reflective pigment. A spinel CrAl2O4 structure with an average particle size of 1 μm demonstrates high NIR reflectance. The CrAl2O4 particles were first modified with 3-methacryloxypropyl trimethoxysilane (MPS-CrAl2O4) to improve their compatibility and dispersion in the polymer matrix. The MPS-CrAl2O4 particles were encapsulated in polymer microcapsules using UV-initiated microsuspension polymerization. Microcapsules based on methyl methacrylate (MMA), butyl acrylate (BA), and ethylene glycol dimethacrylate (EGDMA) were prepared, and the effects of monomer composition and pigment loading on morphology, thermal behavior, NIR reflectance, and coating performance were examined. A monomer ratio of MMA: BA: EGDMA = 50:40:10 yielded spherical microcapsules with good colloidal stability. The NIR reflectance increased with increasing MPS-CrAl2O4 loading, reaching 87% at 40 wt %, which was comparable to that of the original CrAl2O4 particles. Increasing the BA content lowered the glass transition temperature of the microcapsules and promoted coating formation on the glass substrate without an additional binder. Under the specific test conditions used in this work, the microcapsule-coated glass showed a lower interior temperature, with a maximum reduction of about 16 °C, whereas bare glass showed a smaller temperature difference of about 2–3 °C. The results demonstrate that the developed CrAl2O4 particles exhibited effective NIR reflection and can be integrated into coating systems by polymer encapsulation while retaining their NIR-reflective behavior.


  • Controlled precipitation polymerization of molecularly imprinted polymer particles: effect of a chain transfer–catalyst system on particle uniformity and imprinting efficiency

    by Netnapha Kamlangmak, Monjira Luttaprecha, Yunusov Khaydar Ergashovich, Amorn Chaiyasat, Preeyaporn Chaiyasat

  • Open Access

    Efficient Emulsifier-Free Emulsion Copolymerization of Functional Nanoparticles Using Biobased Itaconic Acid

    by Preeyaporn Chaiyasat, Netnapha Kamlangmak, Chutinun Thongbai, Amorn Chaiyasat

    This study investigates the emulsifier-free emulsion polymerization of functional copolymer nanoparticles via a free radical mechanism using potassium persulfate (KPS) as the initiator at 70 °C under. The copolymerization involved styrene (S) with either methacrylic acid (MAA), a conventional petrochemical-derived monomer, or itaconic acid (IA), a renewable monomer derived from biomass fermentation. IA exhibited superior water solubility and functionality due to its two carboxylic acid groups per molecule, enhancing polymerization rate and particle stability. The optimal synthesis’s P­(S-IA) nanoparticles were achieved using 8 mol % IA with pH adjustment at 30 min after initiation, enabling high solid content preparation while maintaining colloidal stability. It demonstrated significantly improved performance over P­(S-MAA) and polystyrene (PS), including complete monomer conversion (∼100%) within 5 h, reduced average particle size (∼200 nm), and minimal coagulation (∼10 wt %) at 30 wt % solid content. In contrast, PS systems exhibited coagulation levels of up to 20% at only 10 wt % solid content, whereas P­(S-MAA) presented coagulation levels of up to 38% under similar conditions. These findings highlight the potential of IA-based functional nanoparticles for ion separation and environmental remediation as precursors for hybrid materials in photocatalysis.


  • Open Access

    Multifunctional Biobased P(EuMA-co-CAMA-co-MAA) Particles for Antimicrobial and Thermal Regulation Applications

    by Saharat Limman, Jittipat Omsinsombon, Preeyaporn Chaiyasat, Amorn Chaiyasat

  • Eco-Friendly Encapsulation: Advancing Biopolymer Microcapsules for Sustainable Performance

    by Kanlapangha Rattanasaikaew, Preeyaporn Chaiyasat

    Biopolymer Innovation: Advanced poly eugenol microcapsules leverage eco-friendly biopolymers for efficient encapsulation, enabling sustainable applications across diverse industries.


  • Open Access

    Microencapsulation of moringa oil in bio-polymer by simple solvent evaporation technique

    by Oraya Kullawong, Amorn Chaiyasat, Preeyaporn Chaiyasat

    Moringa oil (MO) contains various bioactive components and pharmacology. It is attractive to use as a raw ingredient in various products. However, there are limitations on its direct utilization, especially MO's instability and hastening the active ingredient's degradation from external environmental factors, including temperature, humidity, oxidation, light, and heat. To solve these problems, in this work, microencapsulation of MO using different biopolymers as cellulose acetate butyrate (CAB), ethyl cellulose (EC), and poly(L-lactic acid) (PLLA) were carried out by a simple solvent evaporation technique. The prepared polymer microcapsule suspensions were highly colloidal stable for all types of biopolymers and ratios. The spherical biopolymer capsules were formed to a micrometer size after solvent evaporation under all conditions. However, when the microcapsules were dried, aggregation was found with the polymer microcapsules at a ratio of PLLA to MO of 50:50 for all three types of polymers, possibly due to the low amount of polymer to completely encapsulate all of MO. When polymer contents increased to 70%, the dried spherical polymer microcapsules were smoothly produced. Using 70% polymers, the PLLA microcapsule surface was smoother than the polymer microcapsules prepared by CAB and EC which exhibited the dent or hole on the outer surface. Micrometer size, spherical polymer capsules with a core-shell morphology were fabricated. Due to the higher hydrophilicity of the polymer than the MO, the polymer moves outward, forming a strong shell around the MO. Then, all three biopolymers can be used for the microencapsulation of MO at a suitable polymer to MO ratio. However, using PLLA at a ratio of PLLA to MO of 70:30 presented the highest encapsulation efficiency (74.08%), which may be due to its high molecular weight. Because of the non-toxicity and biodegradability of biopolymers, the fabricated microcapsules would be well applied in cosmetic products.