Xing-Xing Yao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Xing-Xing Yao has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Ting Xiao
Zhejiang University
2 shared publications Xiao Ting
School of Physics, Zhejiang University, Hangzhou, Zhejiang 310013, People’s Republic of China
2 shared publicationsYuan Zheng
Zhejiang University
2 shared publicationsZheng Yuan
School of Physics, Zhejiang University, Hangzhou, Zhejiang 310013, People’s Republic of China
2 shared publications- Bo Yang
Zhejiang University
1 shared publication - Fanhao Shen1 shared publication
Latest Publications
- 8 July 2026
- Published by IOP Publishing in European Journal of Physics
- Vol. 47 (4) , 045702
Performance study of a self-assembled pumping straw
This study presents the design and analysis of a self-assembled, triangular straw-based centrifugal pump. A combined theoretical and experimental approach was employed to systematically investigate its pumping mechanism and performance. The effects of key geometric parameters—tube length, inner diameter, and inclination angle—along with the rotational angular velocity on the volumetric flow rate were quantified. The theoretical framework integrates centrifugal force dynamics, Bernoulli’s principle, and a comprehensive fluid resistance model accounting for both frictional and local losses. Experimental validation was performed using a custom-built apparatus equipped with a precision rotation control system and a flow measurement setup, testing a series of 3D-printed straw specimens with varying dimensions. The results indicate that the flow rate increases with angular velocity and the square of the tube diameter, shows an approximate linear dependence on tube length, and requires exceeding a critical angular velocity for pump initiation. This work establishes a predictive model and provides empirical data to guide the design and optimization of such low-cost, easily fabricated micro-scale pumping devices.
- 8 July 2026
- Published by IOP Publishing in European Journal of Physics
- Vol. 47 (4) , 045702
Performance study of a self-assembled pumping straw
This study presents the design and analysis of a self-assembled, triangular straw-based centrifugal pump. A combined theoretical and experimental approach was employed to systematically investigate its pumping mechanism and performance. The effects of key geometric parameters—tube length, inner diameter, and inclination angle—along with the rotational angular velocity on the volumetric flow rate were quantified. The theoretical framework integrates centrifugal force dynamics, Bernoulli’s principle, and a comprehensive fluid resistance model accounting for both frictional and local losses. Experimental validation was performed using a custom-built apparatus equipped with a precision rotation control system and a flow measurement setup, testing a series of 3D-printed straw specimens with varying dimensions. The results indicate that the flow rate increases with angular velocity and the square of the tube diameter, shows an approximate linear dependence on tube length, and requires exceeding a critical angular velocity for pump initiation. This work establishes a predictive model and provides empirical data to guide the design and optimization of such low-cost, easily fabricated micro-scale pumping devices.
- 1 January 2025
- Published by American Association of Physics Teachers (AAPT) in The Physics Teacher
- Vol. 63 (1) , 56-59
See More from Reflection with Fresnel’s Equations
Reflection is a very common daily phenomenon. Except for light sources, we see almost everything by reflection. A large amount of information about objects is b Reflection is a very common daily phenomenon. Except for light sources, we see almost everything by reflection. A large amount of information about objects is b
- 1 January 2025
- Published by American Association of Physics Teachers (AAPT) in The Physics Teacher
- Vol. 63 (1) , 56-59
See More from Reflection with Fresnel’s Equations
Reflection is a very common daily phenomenon. Except for light sources, we see almost everything by reflection. A large amount of information about objects is b Reflection is a very common daily phenomenon. Except for light sources, we see almost everything by reflection. A large amount of information about objects is b
- 6 December 2023
- Published by IOP Publishing in European Journal of Physics
- Vol. 45 (1) , 015002
The motion of a washer on a vertical steel rod
A washer on a vertical steel rod may start spinning instead of simply sliding down. The forces on the washer are analyzed, and the relationship between the angular velocity of rotation and the angular velocity of precession is obtained. A relationship about the coefficient of friction of the washer is obtained at the condition of rotation without slipping. The influence of the coefficient of friction and the ratio of the inner diameter of the washer to the diameter of the rod on the sliding state was investigated experimentally, and a two-dimensional phase diagram of the rotation without slipping was obtained. The relationship between the three parameters(the nutation angle of the washer, the angular velocity of precession, and the final vertical velocity) and the ratio of the inner diameter of the washer to the diameter of the rod in the condition of rotation without slipping was further investigated. The experimental results are in good agreement with the theoretical equations.
- 6 December 2023
- Published by IOP Publishing in European Journal of Physics
- Vol. 45 (1) , 015002
The motion of a washer on a vertical steel rod
A washer on a vertical steel rod may start spinning instead of simply sliding down. The forces on the washer are analyzed, and the relationship between the angular velocity of rotation and the angular velocity of precession is obtained. A relationship about the coefficient of friction of the washer is obtained at the condition of rotation without slipping. The influence of the coefficient of friction and the ratio of the inner diameter of the washer to the diameter of the rod on the sliding state was investigated experimentally, and a two-dimensional phase diagram of the rotation without slipping was obtained. The relationship between the three parameters(the nutation angle of the washer, the angular velocity of precession, and the final vertical velocity) and the ratio of the inner diameter of the washer to the diameter of the rod in the condition of rotation without slipping was further investigated. The experimental results are in good agreement with the theoretical equations.
- Open Access
- 8 August 2023
- Published by MDPI AG in Preprints.org
An Assembled Hot Wire Anemometer Design
The hot wire anemometer is a commonly used device for measuring air speed in laboratories. In this paper, the relationship between air speed and the hot wire temperature in different air speed ranges was analyzed based on the theory of thermal equilibrium. A measurement circuit and hot wire shape were designed based on the principle of the hot wire anemometer, and the linear relationship between current and temperature in the hot wire at different air speeds was verified in an adjustable air speed field. The measured current was used to represent air speed. The designed hot wire anemometer was experimentally validated to provide measurement results that match the theoretical values in different air speed ranges. Finally, the sensitivity of the anemometer in different measurement ranges was determined based on the uncertainty of the instrument's sensitivity and the measurement formula.
- 8 August 2023
- Published by MDPI AG in Preprints.org
Open AccessAn Assembled Hot Wire Anemometer Design
The hot wire anemometer is a commonly used device for measuring air speed in laboratories. In this paper, the relationship between air speed and the hot wire temperature in different air speed ranges was analyzed based on the theory of thermal equilibrium. A measurement circuit and hot wire shape were designed based on the principle of the hot wire anemometer, and the linear relationship between current and temperature in the hot wire at different air speeds was verified in an adjustable air speed field. The measured current was used to represent air speed. The designed hot wire anemometer was experimentally validated to provide measurement results that match the theoretical values in different air speed ranges. Finally, the sensitivity of the anemometer in different measurement ranges was determined based on the uncertainty of the instrument's sensitivity and the measurement formula.
- 10 May 2023
- Published by IOP Publishing in European Journal of Physics
- Vol. 44 (4) , 045001
The rebound height of a capsule-shaped object
The bouncing process of an irregular object falling on the ground contains many interesting mechanical problems. The article investigated the bounce height of a capsule-shaped object when it falls on the ground. The variation of three physical quantities, namely the angle of the object, the linear velocity of the center of mass and the angular velocity relative to the center of mass when it fell on the ground are studied. According to the limit condition of friction, the three-dimensional phase diagram of the above three physical quantities was drawn when the fall height of the capsule-shaped object and the bounce height was equal. The movement of the capsule-shaped object is captured by using two cameras positioned perpendicular to each other. The trajectory was tracked by TRACKER software to obtain the fall height and bounce height of the capsule. When the bounce height was higher than the fall height, it was marked with a red dot. If both heights were equal, it was marked with a black dot. Otherwise, it was marked with a blue dot. Different types of experimental data points are plotted in the phase diagram. A large amount of random experimental data verifies the correctness of the theory.
- 10 May 2023
- Published by IOP Publishing in European Journal of Physics
- Vol. 44 (4) , 045001
The rebound height of a capsule-shaped object
The bouncing process of an irregular object falling on the ground contains many interesting mechanical problems. The article investigated the bounce height of a capsule-shaped object when it falls on the ground. The variation of three physical quantities, namely the angle of the object, the linear velocity of the center of mass and the angular velocity relative to the center of mass when it fell on the ground are studied. According to the limit condition of friction, the three-dimensional phase diagram of the above three physical quantities was drawn when the fall height of the capsule-shaped object and the bounce height was equal. The movement of the capsule-shaped object is captured by using two cameras positioned perpendicular to each other. The trajectory was tracked by TRACKER software to obtain the fall height and bounce height of the capsule. When the bounce height was higher than the fall height, it was marked with a red dot. If both heights were equal, it was marked with a black dot. Otherwise, it was marked with a blue dot. Different types of experimental data points are plotted in the phase diagram. A large amount of random experimental data verifies the correctness of the theory.
- Open Access
- 25 April 2023
- Published by Springer Nature in Research Square
A assembled hot wire anemometer design
The hot wire anemometer is a commonly used device for measuring air speed in laboratories. In this paper, the relationship between air speed and temperature in different air speed ranges was analyzed based on the theory of thermal equilibrium. A measurement circuit and hot wire shape were designed based on the principle of the hot wire anemometer, and the linear relationship between current and temperature in the hot wire at different air speeds was verified in an adjustable air speed field. The measured current was used to represent air speed. The designed hot wire anemometer was experimentally validated to provide measurement results that match the theoretical values in different air speed ranges. Finally, the sensitivity of the anemometer in different measurement ranges was determined based on the uncertainty of the instrument's sensitivity and the measurement formula.
- 25 April 2023
- Published by Springer Nature in Research Square
Open AccessA assembled hot wire anemometer design
The hot wire anemometer is a commonly used device for measuring air speed in laboratories. In this paper, the relationship between air speed and temperature in different air speed ranges was analyzed based on the theory of thermal equilibrium. A measurement circuit and hot wire shape were designed based on the principle of the hot wire anemometer, and the linear relationship between current and temperature in the hot wire at different air speeds was verified in an adjustable air speed field. The measured current was used to represent air speed. The designed hot wire anemometer was experimentally validated to provide measurement results that match the theoretical values in different air speed ranges. Finally, the sensitivity of the anemometer in different measurement ranges was determined based on the uncertainty of the instrument's sensitivity and the measurement formula.
- Open Access
- 1 October 2022
- Published by IOP Publishing in Materials Research Express
- Vol. 9 (10) , 106520
Research on metal wire blowing mechanism and performance
A short metal wire can be used as a fuse in a circuit. Using ANSYS software simulations combined with experiments, it was verified that the highest temperature region during the blowing process of the wire and the most blowing position is near the middle When a direct current flow through. A measurement circuit was established to study the effect of fuse length, and current on fuse blowing time. The results show that for 0.05 mm diameter copper wire, the blowing time decreases rapidly with the increase of length when the length is within 1cm under the action of 3.16A direct current, and the blowing time is basically stable at 0.04s when the length exceeds 1 cm due to the limitation of heat transfer distance. The blowing time of copper wire decreases with the increase of current, and the blowing time is basically stable at 0.05s after the current reaches 3.5A; the melting time of three materials (Cu, Ag, Pb-Sb) all satisfy the theoretical prediction that the product of current density squared and time is constant; the equivalent current density is introduced to modify the theoretical formula, which makes the theory and experiment more in agreement. This study provides a more comprehensive description of the blowing time and characteristics of short metal wires under the action of high current (DC) from both theoretical and experimental aspects.
- 1 October 2022
- Published by IOP Publishing in Materials Research Express
- Vol. 9 (10) , 106520
Open AccessResearch on metal wire blowing mechanism and performance
A short metal wire can be used as a fuse in a circuit. Using ANSYS software simulations combined with experiments, it was verified that the highest temperature region during the blowing process of the wire and the most blowing position is near the middle When a direct current flow through. A measurement circuit was established to study the effect of fuse length, and current on fuse blowing time. The results show that for 0.05 mm diameter copper wire, the blowing time decreases rapidly with the increase of length when the length is within 1cm under the action of 3.16A direct current, and the blowing time is basically stable at 0.04s when the length exceeds 1 cm due to the limitation of heat transfer distance. The blowing time of copper wire decreases with the increase of current, and the blowing time is basically stable at 0.05s after the current reaches 3.5A; the melting time of three materials (Cu, Ag, Pb-Sb) all satisfy the theoretical prediction that the product of current density squared and time is constant; the equivalent current density is introduced to modify the theoretical formula, which makes the theory and experiment more in agreement. This study provides a more comprehensive description of the blowing time and characteristics of short metal wires under the action of high current (DC) from both theoretical and experimental aspects.