Mohammad Zare Ghomsheh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Mohammad Zare Ghomsheh has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
G. Khatibi
3 shared publications- Golta Khatibi
Christian Doppler Laboratory for Lifetime and Reliability of Interfaces in Complex Multi-Material Electronics, Institute for Chemical Technologies and Analytics, TU Wien, 1060 Vienna, Austria
2 shared publications M. Delshadmanesh
2 shared publicationsM. Lederer
2 shared publicationsA. Steiger-Thirsfeld
1 shared publicationB. Weiss
1 shared publication
Latest Publications
- Open Access
The Activation Energy of Strain Bursts during Nanoindentation Creep on Polyethylene
In the present investigation, statistical characterization of strain bursts observed during the load-controlled deformation of high-density polyethylene (HDPE), which arise within the crystalline phase during plastic deformation, was carried out via high-resolution nanoindentation creep experiments. Discrete deformation processes occurred during the nanoindentation creep tests, which indicated that they arose from the break-off of dislocation avalanches, i.e., dislocation climb is a possible mechanism for indentation creep deformation. Characterization of the strain bursts, in terms of the associated height and number, demonstrated that these quantities followed a Gaussian distribution depending on the load and loading rate. This analysis enabled the accurate measurement of creep activation energy. Our method used nanoindentation tests to measure the creep activation energy of HDPE within both the crystalline and amorphous phases. The activation energy of the creep process within the crystalline phase was evaluated using two methods. The frequency of jumps within the crystalline phase, as a function of the strain rate, showed two peaks related to the 5 nm and 10 nm jump sizes that corresponded to the block size within the crystalline lamellae. The results indicated that the intervals coincided with the mean free path of dislocations and the block grain boundaries acted as dislocation barriers. From the dependence of burst frequency on the strain rate and temperature, the activation energy and thermally activated length of the dislocation segment for the plastic slip activation were determined to be 0.66 eV and 20 nm, respectively. Both numbers fit well to the Peterson’s model for the nucleation and motion of thermally activated dislocation segments. A similar activation energy resulted from the differential mechanical analysis of the literature for the αI—transition, which occurred near room temperature in polyethylene. The transition was described as the generation of screw dislocation and its motion along a block grain boundary; therefore, this process is suggested to be the basic mechanism underlying the strain bursts observed in this study.
Open AccessThe Activation Energy of Strain Bursts during Nanoindentation Creep on Polyethylene
In the present investigation, statistical characterization of strain bursts observed during the load-controlled deformation of high-density polyethylene (HDPE), which arise within the crystalline phase during plastic deformation, was carried out via high-resolution nanoindentation creep experiments. Discrete deformation processes occurred during the nanoindentation creep tests, which indicated that they arose from the break-off of dislocation avalanches, i.e., dislocation climb is a possible mechanism for indentation creep deformation. Characterization of the strain bursts, in terms of the associated height and number, demonstrated that these quantities followed a Gaussian distribution depending on the load and loading rate. This analysis enabled the accurate measurement of creep activation energy. Our method used nanoindentation tests to measure the creep activation energy of HDPE within both the crystalline and amorphous phases. The activation energy of the creep process within the crystalline phase was evaluated using two methods. The frequency of jumps within the crystalline phase, as a function of the strain rate, showed two peaks related to the 5 nm and 10 nm jump sizes that corresponded to the block size within the crystalline lamellae. The results indicated that the intervals coincided with the mean free path of dislocations and the block grain boundaries acted as dislocation barriers. From the dependence of burst frequency on the strain rate and temperature, the activation energy and thermally activated length of the dislocation segment for the plastic slip activation were determined to be 0.66 eV and 20 nm, respectively. Both numbers fit well to the Peterson’s model for the nucleation and motion of thermally activated dislocation segments. A similar activation energy resulted from the differential mechanical analysis of the literature for the αI—transition, which occurred near room temperature in polyethylene. The transition was described as the generation of screw dislocation and its motion along a block grain boundary; therefore, this process is suggested to be the basic mechanism underlying the strain bursts observed in this study.
- 5 January 2021
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1016, 1561-1568
Adhesion Properties of Thin Film Multilayers: Comparison of Nanoindentation and Four-Point-Bending Techniques
In this study, we investigated the adhesion strength of SiO2/SiN/TiW/Cu film stacks on silicon by the use of cross-sectional nanoindentation (CSN) technique. The delamination occurred along the SiN/TiW interface as determined by means of SEM and EDX analysis. The critical energy release rate was determined as a quantitative measure of the adhesion strength by application of analytical models as well as Finite Element Method (FEM). Comparative measurements on samples of the same layer composition using the well-established four-point bending (4PB) technique were performed to validate the results of the CSN measurements. FEM was performed to calculate the loading conditions and stress distribution in the samples. The calculations also allowed separating the contribution of plastic and elastic energy in the metallization layers during delamination testing and thereby estimating the value of the interfacial adhesion energy. The experimental results show the good applicability of both the 4PB and CSN method for determining quantitative values of the fracture toughness of thin-film interfaces found in microelectronic components and indicate a good agreement between the two methods.
- 5 January 2021
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1016, 1561-1568
Adhesion Properties of Thin Film Multilayers: Comparison of Nanoindentation and Four-Point-Bending Techniques
In this study, we investigated the adhesion strength of SiO2/SiN/TiW/Cu film stacks on silicon by the use of cross-sectional nanoindentation (CSN) technique. The delamination occurred along the SiN/TiW interface as determined by means of SEM and EDX analysis. The critical energy release rate was determined as a quantitative measure of the adhesion strength by application of analytical models as well as Finite Element Method (FEM). Comparative measurements on samples of the same layer composition using the well-established four-point bending (4PB) technique were performed to validate the results of the CSN measurements. FEM was performed to calculate the loading conditions and stress distribution in the samples. The calculations also allowed separating the contribution of plastic and elastic energy in the metallization layers during delamination testing and thereby estimating the value of the interfacial adhesion energy. The experimental results show the good applicability of both the 4PB and CSN method for determining quantitative values of the fracture toughness of thin-film interfaces found in microelectronic components and indicate a good agreement between the two methods.
- 1 October 2020
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 797
Nanoindentation creep properties of lead-free nanocomposite solders reinforced by modified carbon nanotubes
- 1 October 2020
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 797
Nanoindentation creep properties of lead-free nanocomposite solders reinforced by modified carbon nanotubes
- 1 March 2020
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 777
High cycle fatigue deformation mechanisms of a single phase CrMnFeCoNi high entropy alloy
- 1 March 2020
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 777
High cycle fatigue deformation mechanisms of a single phase CrMnFeCoNi high entropy alloy
- 1 October 2017
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 706, 83-94
Influence of microstructure on fatigue of biocompatible β-phase Ti-45Nb
- 1 October 2017
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 706, 83-94
Influence of microstructure on fatigue of biocompatible β-phase Ti-45Nb
- 14 July 2015
- Published by Wiley in Polymer International
- Vol. 64 (11) , 1537-1543
Analysis of strain bursts during nanoindentation creep of high‐density polyethylene
Nanoindentation creep experiments on polyethylene were carried out in order to investigate dislocation‐based plastic deformation mechanisms. Similarly to that reported in a recent paper (Li J and Ngan AHW, Scr Mater 62:488–491 (2010)), discrete deformation processes occur during nanoindentation creep tests which again seem to arise from the break‐off of dislocation avalanches. That interpretation is supported from systematic studies of the effect of variations of the loading rate and of the applied load on the number and the height of bursts. © 2015 Society of Chemical Industry
- 14 July 2015
- Published by Wiley in Polymer International
- Vol. 64 (11) , 1537-1543
Analysis of strain bursts during nanoindentation creep of high‐density polyethylene
Nanoindentation creep experiments on polyethylene were carried out in order to investigate dislocation‐based plastic deformation mechanisms. Similarly to that reported in a recent paper (Li J and Ngan AHW, Scr Mater 62:488–491 (2010)), discrete deformation processes occur during nanoindentation creep tests which again seem to arise from the break‐off of dislocation avalanches. That interpretation is supported from systematic studies of the effect of variations of the loading rate and of the applied load on the number and the height of bursts. © 2015 Society of Chemical Industry
- 19 July 2012
- Published by Springer Nature in Indian Journal of Physics
- Vol. 86 (10) , 855-858
Two binary stars gravitational waves: homotopy perturbation method
- 19 July 2012
- Published by Springer Nature in Indian Journal of Physics
- Vol. 86 (10) , 855-858
Two binary stars gravitational waves: homotopy perturbation method