Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Héctor Miguel Buenabad Arias has a total of 57 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Comparative optimization of biohydrogen production and purification using pressure swing adsorption

    by Jesse Y. Rumbo-Morales, Gerardo Ortiz-Torres, Alexis U. Salas Villalobos, Felipe D.J. Sorcia-Vázquez, Moises Ramos-Martinez, Carlos Alberto Torres-Cantero, Hector Miguel Buenabad-Arias, Juan Carlos Mixteco-Sánchez, Mario Martínez García, Jorge A. Brizuela-Mendoza, et al.

  • Use of a Passive Finger Exoskeleton and a Continuous Virtual Environment for the Quantitative Assessment of Hand Motor Skills

    by Diego Hernandez-Cabrera, Dante A. Becerra-Martínez, Miguel A. Basurto-Pensado, Luis Gerardo Valle-Cervantes, Alberto O. Ortiz-Zezzatti, Antonio I. Martínez-Santos, Héctor M. Buenabad-Arias

  • Intelligent Vital Signs Simulator Based on Virtual Patients with Medical Orientation in Shock Scenarios

    by Diego Hernández-Cabrera, Alberto Ochoa-Zezzatti, Antonio I. Martínez-Santos, Héctor M. Buenabad-Arias, Laura L. Castro-Gómez, Miguel A. Basurto-Pensado

  • Open Access

    Design and Validation of a Low-Cost Automated Dip-Coater System for Laboratory Applications

    by Cesar H. Guzmán-Valdivia, Héctor R. Azcaray-Rivera, Arturo J. Martínez-Mata, Jorge A. Brizuela-Mendoza, Héctor M. Buenabad-Arias, Agustín Barrera-Sánchez, Andrés Blanco-Ortega

    Dip coating is a widely used laboratory method for depositing thin films and functional coatings. However, commercial dip-coaters remain costly and often exceed the needs of teaching labs and early-stage research. This paper presents a simple, low-cost automated dip-coater capable of delivering repeatable rise–dwell–fall motion for benchtop applications. The system integrates a 3D-printed PLA structure, a stepper-lead-screw actuator, and a PC-hosted graphical user interface that learns and executes user-specified trajectories without additional hardware controls. A compact mathematical model generates triangular and trapezoidal profiles and maps them to step pulses via the steps-per-millimeter factor. The mechatronic design and sequential control are described, and the prototype is validated through simulations and experiments. Non-contact measurements demonstrate high repeatability, accurate dwell timing, and bounded accelerations with minor deviations at switching instants. The bill of materials is 50 USD (≈1–2% of entry-level commercial systems), underscoring stability, robustness, and accessibility for instructional and resource-constrained settings. These results indicate strong potential for routine laboratory use and a clear path to future enhancements.


  • Open Access

    Prototipo: Sistema robótico elevado con tres grados de libertad para rehabilitación de cadera controlado por sistemas embebidos

    by Universidad Autónoma del Estado de Morelos, Héctor Miguel Buenabad Arias, Antonio Isaías Martínez Santos, Andrés Blanco Ortega, Tecnológico Nacional de México, Miguel Ángel Basurto Pensado, Diego Hernández Cabrera

    Este artículo presenta el desarrollo de un prototipo de sistema robótico que permite movimientos en ejes X-Y-Z desde una posición elevada sobre el paciente, diseñado específicamente para la rehabilitación de cadera. El sistema, controlado por sistemas embebidos, proporciona un control preciso y adaptable a las necesidades del paciente durante el proceso de rehabilitación. La estructura del robot permite movimientos controlados y ajustables, promoviendo la futura integración de rutinas, y ejercicios que imiten el rango de movimiento natural de la cadera. Además, el sistema se encuentra optimizado para ser intuitivo, garantizando eficiencia tanto al paciente como para el profesional de salud, facilitando así la rehabilitación y mejorando los resultados funcionales.

  • Open Access

    Desarrollo de un Simulador de Signos Vitales para entrenamiento Médico

    by Universidad Autónoma del Estado de Morelos, Diego Hernández Cabrera, Miguel Ángel Basurto Pensado, Héctor Miguel Buenabad Arias, Antonio Isaías Martínez Santos, Andrés Blanco Ortega, Tecnológico Nacional de México

    Este trabajo presenta el diseño y desarrollo de un simulador de signos vitales para el entrenamiento médico, basado en un software de programación gráfica. El simulador permite la emulación de variables fisiológicas clave, como frecuencia cardíaca, frecuencia respiratoria, presión arterial, temperatura corporal y saturación de oxígeno, permitiendo la práctica en la interpretación de datos en tiempo real. Se diseñó un programa que presenta una interfaz que genera datos fisiológicos ajustables, facilitando la simulación de distintos escenarios clínicos sin requerir la presencia de pacientes reales. Este programa incorpora dos modos de operación: un modo manual, donde el usuario puede modificar los parámetros según los requerimientos del entrenamiento, y un modo precargado, que simula anomalías en los signos vitales con solo el accionamiento de un botón. Además, el simulador está diseñado con una arquitectura basada en un modelo operador-usuario, lo que permite una clara diferenciación de interfaces entre ambos roles. Esto facilita la gestión del sistema por parte del operador y optimiza la experiencia de aprendizaje del usuario. Este simulador representa una herramienta útil para mejorar la formación de estudiantes y profesionales de la salud, contribuyendo a la adquisición de habilidades en la monitorización de signos vitales en entornos controlados.

  • Open Access

    Single-Channel sEMG Hand Gesture Classification Using an Artificial Neural Network Implemented on an ESP32 Microcontroller

    by José Antonio Marbán Salgado, Jorge Arturo Sandoval Espino, Roberto Alan Beltrán Vargas, Jacob Licea-Rodríguez, J. Jesús Escobedo-Alatorre, Héctor Miguel Buenabad Arias, Eliel Rodríguez Salgado

    The implementation of embedded systems for myoelectric signal classification is key to the development of prosthetic and other real-time assistive technologies. This work presents a hand gesture classification system based on an artificial neural network (ANN) deployed on an ESP32 microcontroller. In contrast to approaches that require multiple acquisition channels or complex configurations, the proposed system uses a single surface electromyography (sEMG) channel, reducing cost and complexity. Data were collected from eight participants performing eight hand and wrist gestures. The system achieved classification accuracies of up to 93.05% for six gestures, including rest. Furthermore, the ESP32 implementation demonstrated inference times compatible with real-time operation, achieving an average inference time of 0.17 ms. When using a majority voting strategy, classification accuracy increased to 99%, confirming the feasibility of implementing efficient and accurate gesture recognition on low-cost embedded hardware. These results support its integration into portable and autonomous systems for prosthetic control and other interactive applications.


  • Open Access

    Analysis and Assessment of a Brushless DC Outrunner Motor for Agriculture Drones Using JMAG

    by Javier de la Cruz Soto, Jose J. Gascon-Avalos, Jesse Y. Rumbo-Morales, Gerardo Ortiz-Torres, Manuel A. Zurita-Gil, Felipe D. J. Sorcia-Vázquez, Javier Pérez-Ramírez, Obed A. Valle-López, Susana E. Garcia-Castro, Hector M. Buenabad-Arias, et al.

    Designing propulsion systems for agricultural drones involves a repetitive process that is both expensive and time-intensive. At the same time, conducting comprehensive experimental tests demands specialized equipment and strict safety protocols. In this work, the design and assessment of the propulsion system (propeller, motor, and battery) for large-sized drones in agricultural applications are conducted using numerical methods. To properly predict and validate the performance of a brushless direct current motor, a three half-bridge inverter circuit, featuring a trapezoidal commutation, is implemented and constructed. First, the propeller is studied using the finite volume method, obtaining a maximum variation of 6.32% for thrust and 10.1% for torque. Additionally, an electromagnetic analysis on a commercial brushless direct current motor (BLDC) using JMAG software from JSOL corporation (JMAG designer 23.2, Cd.Obregón, México) resulted in 4.43% deviation from experimental electrical measurements. The selected propulsion system is implemented in a 30 kg drone, where motor performance is evaluated for two instants of time in a typical agriculture trajectory. The findings demonstrate that numerical methods provide valuable insights in large-sized unmanned aerial vehicle (UAV) design, decreasing the experimental tests conducted and accelerating implementation time.


  • Open Access

    Design, Construction and Finite Element Analysis of a Hexacopter for Precision Agriculture Applications

    by Miguel Ernesto Gutierrez-Rivera, Jesse Y. Rumbo-Morales, Gerardo Ortiz-Torres, Jose J. Gascon-Avalos, Felipe D. J. Sorcia-Vázquez, Carlos Alberto Torres-Cantero, Hector M. Buenabad-Arias, Iván Guillen-Escamilla, Maria A. López-Osorio, Manuel A. Zurita-Gil, et al.

    Agriculture drones face important challenges regarding autonomy and construction, as flying time below the 9-minute mark is the norm, and their manufacture requires several tests and research before reaching proper flight dynamics. Therefore, correct design, analysis, and manufacture of the structure are imperative to address the aforementioned problems and ensure a robust build that withstands the tough environments of this application. In this work, the analysis and implementation of a Nylamid motor bracket, aluminum sandwich-type skeleton, and carbon fiber tube arm in a 30 kg agriculture drone is presented. The mechanical response of these components is evaluated using the finite element method in ANSYS Workbench, and the material behavior assumptions are assessed using a universal testing machine before their implementations. The general description of these models and the numerical results are presented. This early prediction of the behavior of the structure allows for mass optimization and cost reductions. The fast dynamics of drone applications set important restrictions in ductile materials such as this, requiring extensive structural analysis before manufacture. Experimental and numerical results showed a maximum variation of 8.7% for the carbon fiber composite and 13% for the Nylamid material. The mechanical properties of polyamide nylon allowed for a 51% mass reduction compared to a 6061 aluminum alloy structure optimized for the same load case in the motor brackets design. The low mechanical complexity of sandwich-type skeletons translated into fast implementation. Finally, the overall performance of the agriculture drone is evaluated through the data gathered during the flight test, showing the adequate design process.


  • Open Access

    Geometric Control and Structure-at-Infinity Control for Disturbance Rejection and Fault Compensation Regarding Buck Converter-Based LED Driver

    by Jesse Y. Rumbo-Morales, Jair Gómez-Radilla, Gerardo Ortiz-Torres, Felipe D. J. Sorcia-Vázquez, Hector M. Buenabad-Arias, Maria A. López-Osorio, Carlos A. Torres-Cantero, Moises Ramos-Martinez, Mario A. Juárez, Manuela Calixto-Rodriguez, et al.

    Currently, various light-emitting diode (LED) lighting systems are being developed because LEDs are one of the most used lighting sources for work environments, buildings, homes, and public roads in terms of some of their applications. Similarly, they have low energy consumption, quick responses, and excellent optimal performance in their operation. However, these systems still need to precisely regulate lighting, maintain stable voltage and current in the presence of faults and disturbances, and have a wide range of operations in the event of trajectory changes or monitoring tasks regarding the desired voltage and current. This work presents the design and application of two types of robust controllers (structure-at-infinity control and geometric control) applied to an LED driver using a buck converter. The controllers aim to follow the desired trajectories, attenuate disturbances at the power supply input, and compensate for faults in the actuator (MOSFET) to keep the capacitor voltage and inductor current stable. When comparing the results obtained with the two controllers, it was observed that both present excellent performance in the presence of constant disturbances. However, in scenarios in which variable faults and path changes are implemented, the structure-at-infinity control method shows an overimpulse of output voltage and current ranging from 39 to 42 volts and from 0.3 to 0.45 A, with a margin of error of 1%, and it can generate a failure in the LED driver using a buck converter. On the other hand, when using geometric control, the results are satisfactory, achieving attenuating constant disturbances and variable faults, reaching the desired voltage (40 v to 35 v) and current (0.3 to 0.25 A) with a margin of error of 0.05%, guaranteeing a system without overvoltages or the accelerated degradation of the components due to magnetic conductivity.