Ignacio Collado
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ignacio Collado has a total of 52 co-authors. Here are the top co-authors by number of shared publications:
- Antonio Vázquez-López
Materials Science and Engineering Area, Escuela Superior de Ciencias Experimentales y Tecnología, Universidad Rey Juan Carlos, C/Tulipán s/n, 28933 Madrid, Spain
10 shared publications - Silvia Gonzalez Prolongo
Materials Science and Engineering Area, Rey Juan Carlos University, C/Tulipán s/n, 28933 Móstoles, Madrid, Spain
9 shared publications - Alberto Jiménez-Suárez
Rey Juan Carlos University
7 shared publications Jimena de la Vega
6 shared publications- De-Yi Wang
IMDEA Materials Institute Madrid Spain
5 shared publications - José Sánchez del Río
IMDEA Materials Institute, C/Eric Kandel, 2, 28906 Getafe, Madrid, Spain; Departamento de Ingeniería Eléctrica, Electrónica Automática y Física Aplicada, ETSIDI, Universidad Politécnica de Madrid, Ronda de Valencia 3, 28012 Madrid, Spain
4 shared publications
Latest Publications
- Open Access
- 21 February 2026
- Published by Springer Nature in Advanced Composites and Hybrid Materials
- Vol. 9 (2)
Dual-curing vitrimeric composite with magnetically triggered remote shape memory and de-icing: functional performance and analytical modeling of ice detachment
- 21 February 2026
- Published by Springer Nature in Advanced Composites and Hybrid Materials
- Vol. 9 (2)
Open AccessDual-curing vitrimeric composite with magnetically triggered remote shape memory and de-icing: functional performance and analytical modeling of ice detachment
- Open Access
- 18 August 2025
- Published by Elsevier in Composites Part B: Engineering
- Vol. 307
Multifunctional sequential dual curing electroactive graphene Nanocomposites: Self-heating, de-icing and in-situ curing
- 18 August 2025
- Published by Elsevier in Composites Part B: Engineering
- Vol. 307
Open AccessMultifunctional sequential dual curing electroactive graphene Nanocomposites: Self-heating, de-icing and in-situ curing
- 4 June 2025
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 7 (12) , 5442-5450
Fully Fabric Triboelectric Nanogenerators Based on SWCNH-Coated Cotton Fabric/UHMWPE: IoT Sensing
- 4 June 2025
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 7 (12) , 5442-5450
Fully Fabric Triboelectric Nanogenerators Based on SWCNH-Coated Cotton Fabric/UHMWPE: IoT Sensing
- 24 May 2025
- Published by Wiley in Polymer Composites
- Vol. 46 (15) , 14310-14320
Single‐Walled Carbon Nanohorns Functionalization of PVA / PDMS for Flexible Triboelectric Nanogenerators: IoT Remote Gait Sensor
Composite nanomaterials comprise emerging materials for triboelectric nanogenerators (TENGs), as they provide higher voltage output than pristine polymer‐based systems. Currently, efforts are aimed at improving the charge transfer between the tribolayers, which could be obtained by nanomaterial doping. Herein, the effect of synthesized single‐walled carbon nanohorns (SWCNHs), an alternative to conventional carbon nanotubes (CNTs), on two different materials, polyvinyl alcohol (PVA) and polydimethylsiloxane (PDMS) is studied. In both cases, the addition of SWCNHs increases the dielectric constant of the layers. The TENG with the modified PDMS (mPDMS) showed the maximum voltage output, almost duplicating the one obtained with the pristine sample. Furthermore, a possible Internet of Things (IoT) application has been demonstrated, with the use of wireless technology and Lo‐Ra communications as a gait sensor to provide evolution and information regarding the health condition and the footprint of a patient.
- 24 May 2025
- Published by Wiley in Polymer Composites
- Vol. 46 (15) , 14310-14320
Single‐Walled Carbon Nanohorns Functionalization of PVA / PDMS for Flexible Triboelectric Nanogenerators: IoT Remote Gait Sensor
Composite nanomaterials comprise emerging materials for triboelectric nanogenerators (TENGs), as they provide higher voltage output than pristine polymer‐based systems. Currently, efforts are aimed at improving the charge transfer between the tribolayers, which could be obtained by nanomaterial doping. Herein, the effect of synthesized single‐walled carbon nanohorns (SWCNHs), an alternative to conventional carbon nanotubes (CNTs), on two different materials, polyvinyl alcohol (PVA) and polydimethylsiloxane (PDMS) is studied. In both cases, the addition of SWCNHs increases the dielectric constant of the layers. The TENG with the modified PDMS (mPDMS) showed the maximum voltage output, almost duplicating the one obtained with the pristine sample. Furthermore, a possible Internet of Things (IoT) application has been demonstrated, with the use of wireless technology and Lo‐Ra communications as a gait sensor to provide evolution and information regarding the health condition and the footprint of a patient.
- Open Access
- 17 May 2025
- Published by Elsevier in Chemical Engineering Journal
- Vol. 515
Dual-Curing MWCNT nanocomposites for Energy-Efficient electroactive shape memory and In-Situ processing
- 17 May 2025
- Published by Elsevier in Chemical Engineering Journal
- Vol. 515
Open AccessDual-Curing MWCNT nanocomposites for Energy-Efficient electroactive shape memory and In-Situ processing
- 12 March 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (12) , 18954-18970
Electromagnetic Interference Shielding of a Sequential Dual-Curing Thiol–Epoxy System Reinforced with GNPs with High Shape Memory
Modern electronics face several challenges during operation, such as interference of disruptive electromagnetic signals and high temperatures within a limited space. Both electromagnetic interference (EMI) and thermal management could be tackled simultaneously by employing smart efficient materials with high thermal and electrical conductivity. A dual-curing epoxy system, a new subset of adaptable materials, could potentially solve those challenges, with the proper selection of the reinforcement. Moreover, its manufacturing and synthesis process, which involves a sequential curing stage, constitute an attractive, selective, and fast methodology. The thiol-epoxy chemistry allows the synthesis of an epoxy system with high shape-memory capabilities while retaining optimal mechanical properties. Herein, dual-curing epoxy systems reinforced with graphene nanoplatelets (GNPs) are manufactured. The influence of the GNPs content is evaluated, which greatly increases upon loading while retaining a high shape-memory fixation and recovery rates (near 99%). A maximum EMI shielding efficiency of 24 dB is achieved for the higher GNPs content, which is endowed by the high electrical conductivity of the system. Moreover, a modelization of the near-field and far-field EMI shielding is reported, which agrees with experimental observation. This report shows the potential and multifunctional nature of dual-curing epoxy composites for EMI shielding and shape-memory-related application.
- 12 March 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (12) , 18954-18970
Electromagnetic Interference Shielding of a Sequential Dual-Curing Thiol–Epoxy System Reinforced with GNPs with High Shape Memory
Modern electronics face several challenges during operation, such as interference of disruptive electromagnetic signals and high temperatures within a limited space. Both electromagnetic interference (EMI) and thermal management could be tackled simultaneously by employing smart efficient materials with high thermal and electrical conductivity. A dual-curing epoxy system, a new subset of adaptable materials, could potentially solve those challenges, with the proper selection of the reinforcement. Moreover, its manufacturing and synthesis process, which involves a sequential curing stage, constitute an attractive, selective, and fast methodology. The thiol-epoxy chemistry allows the synthesis of an epoxy system with high shape-memory capabilities while retaining optimal mechanical properties. Herein, dual-curing epoxy systems reinforced with graphene nanoplatelets (GNPs) are manufactured. The influence of the GNPs content is evaluated, which greatly increases upon loading while retaining a high shape-memory fixation and recovery rates (near 99%). A maximum EMI shielding efficiency of 24 dB is achieved for the higher GNPs content, which is endowed by the high electrical conductivity of the system. Moreover, a modelization of the near-field and far-field EMI shielding is reported, which agrees with experimental observation. This report shows the potential and multifunctional nature of dual-curing epoxy composites for EMI shielding and shape-memory-related application.
- Open Access
- 4 March 2025
- Published by Springer Nature in Advanced Composites and Hybrid Materials
- Vol. 8 (2) , 1-21
Nanocomposites of sequential dual curing of thiol-epoxy systems with Fe3O4 nanoparticles for remote/in situ applications: thermomechanical, shape memory, and induction heating properties
Sequential dual-curing epoxy composites, such as the thiol-epoxy system, can potentially open new capabilities for end-products in the composite industry. This system remains stable after the initial curing and can undergo further reactions when exposed to a second stimulus, such as the use of magnetic induction: a remote and energy-efficient alternative. This study reports the first dual-curing thiol-epoxy resin reinforced with magnetic nanoparticles Fe3O4. The addition of Fe3O4 nanoparticles endows the polymer matrix with dual-stimuli shape memory, triggered by both conventional heating and the use of a magnetic field, broadening potential applications. The study examined various manufacturing conditions and loadings of Fe3O4, which improved the mechanical properties of the composites. The dual-response shape memory was evaluated by heating the polymer with both a conventional heat source and magnetic fields, resulting in a ~ 100% shape fixation and recovery ratio for either stimulus source, with superior performance under the magnetic field. Furthermore, under moderate magnetic fields, the system was able to reach temperatures as high as 160 °C, and the influence of various parameters on the efficiency of magnetic induction heating was studied by statistical analysis of design of experiments. Additionally, two proofs of concept were presented. In the first, the second curing step was performed under the in situ heating generated by the magnetic field, successfully fixing the temporary shape into the permanent form of the sample. In the second concept, the system was utilized as a smart switch or a threshold temperature sensor. Graphical Abstract
- 4 March 2025
- Published by Springer Nature in Advanced Composites and Hybrid Materials
- Vol. 8 (2) , 1-21
Open AccessNanocomposites of sequential dual curing of thiol-epoxy systems with Fe3O4 nanoparticles for remote/in situ applications: thermomechanical, shape memory, and induction heating properties
Sequential dual-curing epoxy composites, such as the thiol-epoxy system, can potentially open new capabilities for end-products in the composite industry. This system remains stable after the initial curing and can undergo further reactions when exposed to a second stimulus, such as the use of magnetic induction: a remote and energy-efficient alternative. This study reports the first dual-curing thiol-epoxy resin reinforced with magnetic nanoparticles Fe3O4. The addition of Fe3O4 nanoparticles endows the polymer matrix with dual-stimuli shape memory, triggered by both conventional heating and the use of a magnetic field, broadening potential applications. The study examined various manufacturing conditions and loadings of Fe3O4, which improved the mechanical properties of the composites. The dual-response shape memory was evaluated by heating the polymer with both a conventional heat source and magnetic fields, resulting in a ~ 100% shape fixation and recovery ratio for either stimulus source, with superior performance under the magnetic field. Furthermore, under moderate magnetic fields, the system was able to reach temperatures as high as 160 °C, and the influence of various parameters on the efficiency of magnetic induction heating was studied by statistical analysis of design of experiments. Additionally, two proofs of concept were presented. In the first, the second curing step was performed under the in situ heating generated by the magnetic field, successfully fixing the temporary shape into the permanent form of the sample. In the second concept, the system was utilized as a smart switch or a threshold temperature sensor. Graphical Abstract