Ajay Kumar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ajay Kumar has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
M. A. Iqbal
Indian Institute of Technology Roorkee, Roorkee, India
5 shared publications- Kailash Kumar
Indian Institute of Technology Roorkee
2 shared publications Hrishikesh Sharma
Associate Professor, Dept. of Civil Engineering, Indian Institute of Technology Guwahati, Guwahati, Assam 781039, India
1 shared publicationJaswanth Gangolu
Assistant Professor, Dept. of Civil Engineering, Aditya Engineering College, Surampalem, East Godavari District, Andhra Pradesh 533437, India
1 shared publicationM.A. Iqbal
1 shared publication- Mohammad Mohsin Khan
Department of Civil Engineering, Indian Institute of Technology, Roorkee, India
1 shared publication
Latest Publications
- 11 October 2025
- Published by Elsevier in Engineering Failure Analysis
- Vol. 183
Influence of prestressing force on the ballistic performance of small-scale prestressed containment walls
- 11 October 2025
- Published by Elsevier in Engineering Failure Analysis
- Vol. 183
Influence of prestressing force on the ballistic performance of small-scale prestressed containment walls
- 22 May 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (8) , 6615-6635
Material Characterization of 550D Reinforcing Steel Bar at High Strain Rates
- 22 May 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (8) , 6615-6635
Material Characterization of 550D Reinforcing Steel Bar at High Strain Rates
- 3 May 2024
- Published by Springer Nature
- p. 81-90
Numerical Study of Damage Evaluation of Plain Concrete Under Projectile Impact
- 3 May 2024
- Published by Springer Nature
- p. 81-90
Numerical Study of Damage Evaluation of Plain Concrete Under Projectile Impact
- 24 April 2024
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 10 (3) , 297-315
Dynamic Tensile and Compressive Behavior Prestressing Steel Wire at the High Strain Rate
- 24 April 2024
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 10 (3) , 297-315
Dynamic Tensile and Compressive Behavior Prestressing Steel Wire at the High Strain Rate
- 16 December 2023
- Published by World Scientific Pub Co Pte Ltd in International Journal of Structural Stability and Dynamics
- Vol. 25 (02)
Numerical Investigation of Tensile and Compressive Behavior of Mild Steel Subjected to High Strain Rate
Numerical simulations were conducted to validate computational and constitutive models for steel materials through dynamic material tests involving both tension and compression. These simulations involved the numerical modeling of the split Hopkinson pressure bar (SHPB) apparatus, with the appropriate loading applied directly in compression and indirectly in tension. To induce a tensile wave within the specimen, a shoulder, such as a coupler or collar, was interposed between the bars. The simulations were carried out using the LS-DYNA finite element code. In these numerical simulations of the SHPB tests, the MAT-15 Johnson–Cook material model was applied to represent mild steel. The resulting stress–strain relationships obtained under both compression and tension conditions were subsequently compared to corresponding experimental data. The primary objectives of these simulations were to determine the optimal placement of strain gauges on both the input and output bars of the tensile SHPB setup. Additionally, the simulations aimed to assess the influence of the gauge length-to-diameter ratio on the behavior of the mild steel specimen subjected to dynamic tension and compression. The results showed that the pulse produced due to the mechanical mismatch of the element at boundaries can be avoided using the length of the input bar smaller than the output bar. Further, the location of the strain gauge in the case of the output bar should be toward the output bar-shoulder interface, while in the case of the input bar, it should be considered at the center of the span of the bar.
- 16 December 2023
- Published by World Scientific Pub Co Pte Ltd in International Journal of Structural Stability and Dynamics
- Vol. 25 (02)
Numerical Investigation of Tensile and Compressive Behavior of Mild Steel Subjected to High Strain Rate
Numerical simulations were conducted to validate computational and constitutive models for steel materials through dynamic material tests involving both tension and compression. These simulations involved the numerical modeling of the split Hopkinson pressure bar (SHPB) apparatus, with the appropriate loading applied directly in compression and indirectly in tension. To induce a tensile wave within the specimen, a shoulder, such as a coupler or collar, was interposed between the bars. The simulations were carried out using the LS-DYNA finite element code. In these numerical simulations of the SHPB tests, the MAT-15 Johnson–Cook material model was applied to represent mild steel. The resulting stress–strain relationships obtained under both compression and tension conditions were subsequently compared to corresponding experimental data. The primary objectives of these simulations were to determine the optimal placement of strain gauges on both the input and output bars of the tensile SHPB setup. Additionally, the simulations aimed to assess the influence of the gauge length-to-diameter ratio on the behavior of the mild steel specimen subjected to dynamic tension and compression. The results showed that the pulse produced due to the mechanical mismatch of the element at boundaries can be avoided using the length of the input bar smaller than the output bar. Further, the location of the strain gauge in the case of the output bar should be toward the output bar-shoulder interface, while in the case of the input bar, it should be considered at the center of the span of the bar.
- 1 December 2023
- Published by Allerton Press in Mechanics of Solids
- Vol. 58 (9) , 3315-3332
Development of Tensile Split Hopkinson Pressure Bar Technique for Studying the Dynamic Behaviour of Metals
The tensile split-Hopkinson pressure bar (SHPB) system is significantly used for dynamic material characterization of metals in the range of strain rates 1
- 1 December 2023
- Published by Allerton Press in Mechanics of Solids
- Vol. 58 (9) , 3315-3332
Development of Tensile Split Hopkinson Pressure Bar Technique for Studying the Dynamic Behaviour of Metals
The tensile split-Hopkinson pressure bar (SHPB) system is significantly used for dynamic material characterization of metals in the range of strain rates 1
- 1 August 2022
- Published by American Society of Civil Engineers (ASCE) in Practice Periodical on Structural Design and Construction
- Vol. 27 (3) , 04022027
Performance-Based Code Calibration and Total Probability of Failure of the Nuclear Containment Structure Subjected to Missile Impact
The multifarious calamities upon nuclear containment structures (NCS) and insufficient reliability-based factors inspired the current study for the investigation of hard missile impact. Available codes for design and construction of NCS suggest a load factor of 1.0 and basic information for the missile impact scenarios. However, the current study proposes novel reliability-based load and resistance factors for NCS subjected to a hard missile impact. The performance-based probabilistic energy capacity and demand models have been used for the code calibration process. These models were based on three performance levels associated with four levels of damage. The levels were chosen based on local damage due to its rigidity from insignificant penetration to complete perforation of the missile. This study also developed hazard curves for various distributions of missile mass and velocity. The total probability of failure of NCS was calculated based on a realistic range of material and geometrical variables and globally existing cruise missiles, wind-borne missiles, pressure pipes, iron rods, and others. The current investigation considers all the inherent uncertainties of target and missile. This study circumvents the limitations and develops performance-based load and resistance factors based on probabilistic models. The developed load and resistance factors for codal provisions are tied in turn to the different performance levels of the NCS. These factors can be used for the design of NCS, bunkers, silos, storage tanks, slabs, and others without performing exhaustive analysis and/or experiments.
- 1 August 2022
- Published by American Society of Civil Engineers (ASCE) in Practice Periodical on Structural Design and Construction
- Vol. 27 (3) , 04022027
Performance-Based Code Calibration and Total Probability of Failure of the Nuclear Containment Structure Subjected to Missile Impact
The multifarious calamities upon nuclear containment structures (NCS) and insufficient reliability-based factors inspired the current study for the investigation of hard missile impact. Available codes for design and construction of NCS suggest a load factor of 1.0 and basic information for the missile impact scenarios. However, the current study proposes novel reliability-based load and resistance factors for NCS subjected to a hard missile impact. The performance-based probabilistic energy capacity and demand models have been used for the code calibration process. These models were based on three performance levels associated with four levels of damage. The levels were chosen based on local damage due to its rigidity from insignificant penetration to complete perforation of the missile. This study also developed hazard curves for various distributions of missile mass and velocity. The total probability of failure of NCS was calculated based on a realistic range of material and geometrical variables and globally existing cruise missiles, wind-borne missiles, pressure pipes, iron rods, and others. The current investigation considers all the inherent uncertainties of target and missile. This study circumvents the limitations and develops performance-based load and resistance factors based on probabilistic models. The developed load and resistance factors for codal provisions are tied in turn to the different performance levels of the NCS. These factors can be used for the design of NCS, bunkers, silos, storage tanks, slabs, and others without performing exhaustive analysis and/or experiments.