Tomonari Inamura
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tomonari Inamura has a total of 71 co-authors. Here are the top co-authors by number of shared publications:
- Hideki Hosoda
Institute of Innovative Research (IIR), Tokyo Institute of Technology, Yokohama, Japan
21 shared publications - Shuichi Miyazaki
University of Hyogo
7 shared publications - Masaki Tahara
Institute of Innovative Research (IIR), Tokyo Institute of Technology, 4259 Nagatsuta-cho, Midori-ku, Yokohama 226-8503, Japan
6 shared publications - Wan-Ting Chiu
School of Materials and Chemical Technology
4 shared publications - Hee Young Kim
Graduate School of Pure and Applied Sciences, University of Tsukuba, Tsukuba, Ibaraki 305-8573, Japan
3 shared publications Yuri Shinohara
Department of Mechanical and Intelligent Systems Engineering, The University of Electro-Communications
3 shared publications
Latest Publications
- 19 December 2025
- Published by Elsevier in Materialia
- Vol. 45
Geometric accommodation of local incompatibility of parent/martensite interface by transformation-induced dislocations in Ti–Ni
- 19 December 2025
- Published by Elsevier in Materialia
- Vol. 45
Geometric accommodation of local incompatibility of parent/martensite interface by transformation-induced dislocations in Ti–Ni
- Open Access
- 23 June 2025
- Published by Springer Nature in Shape Memory and Superelasticity
- Vol. 11 (3) , 579-592
Lattice Parameters of B2 and B19′ Phases in Ti–Ni Alloys Near Transformation Temperatures: Effects of Ni Concentration and Temperature
The Ni concentration and temperature dependence of the lattice parameters of the B2 and B19′ phases in binary Ti–Ni alloys was systematically clarified near the martensitic transformation temperatures, using samples with finely varied Ni concentrations ranging from 50.00 to 51.00 at.%. The differences between the present data and previously reported values were quantitatively explained and reinterpreted in terms of uncertainties in Ni concentration, measurement conditions, thermal history, and extrapolation methods. Furthermore, based on the lattice parameters obtained in this study, the effect of Ni concentration on the suppression of transformation-induced dislocations and the stabilization of thermal cycling behavior was discussed in terms of geometrical incompatibility. From the perspectives of composition increment, temperature steps, consistency in thermal history, and transparency of extrapolation procedure, the present dataset is considered to be among the most accurate, precise, and consistent lattice parameter datasets currently available. This dataset provides a highly reliable basis for evaluating the variation in lattice parameters among literature and serves as a foundation for future investigations into phase transformation behavior in Ti–Ni alloys.
- 23 June 2025
- Published by Springer Nature in Shape Memory and Superelasticity
- Vol. 11 (3) , 579-592
Open AccessLattice Parameters of B2 and B19′ Phases in Ti–Ni Alloys Near Transformation Temperatures: Effects of Ni Concentration and Temperature
The Ni concentration and temperature dependence of the lattice parameters of the B2 and B19′ phases in binary Ti–Ni alloys was systematically clarified near the martensitic transformation temperatures, using samples with finely varied Ni concentrations ranging from 50.00 to 51.00 at.%. The differences between the present data and previously reported values were quantitatively explained and reinterpreted in terms of uncertainties in Ni concentration, measurement conditions, thermal history, and extrapolation methods. Furthermore, based on the lattice parameters obtained in this study, the effect of Ni concentration on the suppression of transformation-induced dislocations and the stabilization of thermal cycling behavior was discussed in terms of geometrical incompatibility. From the perspectives of composition increment, temperature steps, consistency in thermal history, and transparency of extrapolation procedure, the present dataset is considered to be among the most accurate, precise, and consistent lattice parameter datasets currently available. This dataset provides a highly reliable basis for evaluating the variation in lattice parameters among literature and serves as a foundation for future investigations into phase transformation behavior in Ti–Ni alloys.
- 5 May 2024
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 298
Origin of bent ridge-kink based on disclination relaxation
- 5 May 2024
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 298
Origin of bent ridge-kink based on disclination relaxation
- Open Access
- 1 March 2024
- Published by Japan Institute of Metals in MATERIALS TRANSACTIONS
- Vol. 65 (3) , 352-355
Comparison of Dislocation Accumulation Behavior upon Thermal Cycling in Ti–30Ni–20Cu and Ti–39Ni–11Pd Shape Memory Alloys
Accumulation behavior of transformation-induced dislocation upon thermal cycling of Ti-30Ni-20Cu which satisfies the triplet condition (TC) was compared to that of Ti-39Ni-11Pd which is known as low hysteresis shape memory alloy designed by the condition that the middle eigenvalue of lattice deformation is 1 (CC1). The dislocation density was determined by the Williamson-Hall method. Although the 0.2% proof stress of the Ti-30Ni-20Cu alloy was about half that of the Ti-39Ni-11Pd alloy, the dislocation accumulation behavior was almost the same in both alloys. The formation of transformation-induced dislocation is effectively suppressed by satisfying TC, more than equivalently to satisfying CC1 only.TC is suggested to be a new guideline to design durable shape memory alloy.
- 1 March 2024
- Published by Japan Institute of Metals in MATERIALS TRANSACTIONS
- Vol. 65 (3) , 352-355
Open AccessComparison of Dislocation Accumulation Behavior upon Thermal Cycling in Ti–30Ni–20Cu and Ti–39Ni–11Pd Shape Memory Alloys
Accumulation behavior of transformation-induced dislocation upon thermal cycling of Ti-30Ni-20Cu which satisfies the triplet condition (TC) was compared to that of Ti-39Ni-11Pd which is known as low hysteresis shape memory alloy designed by the condition that the middle eigenvalue of lattice deformation is 1 (CC1). The dislocation density was determined by the Williamson-Hall method. Although the 0.2% proof stress of the Ti-30Ni-20Cu alloy was about half that of the Ti-39Ni-11Pd alloy, the dislocation accumulation behavior was almost the same in both alloys. The formation of transformation-induced dislocation is effectively suppressed by satisfying TC, more than equivalently to satisfying CC1 only.TC is suggested to be a new guideline to design durable shape memory alloy.
- Open Access
- 1 January 2024
- Published by Iron and Steel Institute of Japan in Proceedings of International Symposia on Steel Science
- Vol. 2024, 43-48
Magnitude of incompatibility between habit plane variants related by 180° rotation
Rigid body rotation is required for paired martensite variants to maintain continuity of deformation at their junction plane. The magnitude of this rigid body rotation, θ, serves as an indicator of the energy barrier associated with variant coupling, and to some extent explains the variant selection rule in the variant pairing. In this paper, an analytical solution for θ is derived. We assume that the deformation gradient of the martensitic plate is given by U=I+gd⊗p as the phenomenological theory of martensite, and the two variants are related by 180° rotations about some axis ê. The variant pairs related by a 180° rotation account for nearly all the major variant pairs observed in steel. Then, θ is analytically determined using d, p, and ê. Notably, θ is zero when d and ê are perpendicular, or when p and ê are parallel.
- 1 January 2024
- Published by Iron and Steel Institute of Japan in Proceedings of International Symposia on Steel Science
- Vol. 2024, 43-48
Open AccessMagnitude of incompatibility between habit plane variants related by 180° rotation
Rigid body rotation is required for paired martensite variants to maintain continuity of deformation at their junction plane. The magnitude of this rigid body rotation, θ, serves as an indicator of the energy barrier associated with variant coupling, and to some extent explains the variant selection rule in the variant pairing. In this paper, an analytical solution for θ is derived. We assume that the deformation gradient of the martensitic plate is given by U=I+gd⊗p as the phenomenological theory of martensite, and the two variants are related by 180° rotations about some axis ê. The variant pairs related by a 180° rotation account for nearly all the major variant pairs observed in steel. Then, θ is analytically determined using d, p, and ê. Notably, θ is zero when d and ê are perpendicular, or when p and ê are parallel.
- Open Access
- 14 August 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (8) , 1604
Investigations of Shape Deformation Behaviors of the Ferromagnetic Ni–Mn–Ga Alloy/Porous Silicone Rubber Composite towards Actuator Applications
Ferromagnetic shape memory alloys (FSMAs), which are potential candidates for future technologies (i.e., actuators in robots), have been paid much attention for their high work per volume and rapid response as external stimulation, such as a magnetic field, is imposed. Among all the FSMAs, the Ni–Mn–Ga-based alloys were considered promising materials due to their appropriate phase transformation temperatures and ferromagnetism. Nevertheless, their intrinsic embrittlement issue and sluggish twin motion due to the inhibition of grain boundaries restrict their practicability. This study took advantage of the single-crystal Ni–Mn–Ga cube/silicone rubber composite materials to solve the two aforementioned difficulties. The single-crystal Ni–Mn–Ga cube was prepared by using a high-temperature alloying procedure and a floating-zone (FZ) method, and the cubes were verified to be the near-{100}p Ni–Mn–Ga alloy. Various room temperature (RT) curing silicone rubbers were utilized as matrix materials. Furthermore, polystyrene foam particles (PFP) were used to provide pores, allowing a porous silicone rubber matrix. It was found that the elastic modulus of the silicone rubber was successfully reduced by introducing the PFP. Additionally, the magnetic field-induced martensite variant reorientation (MVR) was greatly enhanced by introducing a porous structure into the silicone rubber. The single-crystal Ni–Mn–Ga cube/porous silicone rubber composite materials are considered to be promising materials for applications in actuators.
- 14 August 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (8) , 1604
Open AccessInvestigations of Shape Deformation Behaviors of the Ferromagnetic Ni–Mn–Ga Alloy/Porous Silicone Rubber Composite towards Actuator Applications
Ferromagnetic shape memory alloys (FSMAs), which are potential candidates for future technologies (i.e., actuators in robots), have been paid much attention for their high work per volume and rapid response as external stimulation, such as a magnetic field, is imposed. Among all the FSMAs, the Ni–Mn–Ga-based alloys were considered promising materials due to their appropriate phase transformation temperatures and ferromagnetism. Nevertheless, their intrinsic embrittlement issue and sluggish twin motion due to the inhibition of grain boundaries restrict their practicability. This study took advantage of the single-crystal Ni–Mn–Ga cube/silicone rubber composite materials to solve the two aforementioned difficulties. The single-crystal Ni–Mn–Ga cube was prepared by using a high-temperature alloying procedure and a floating-zone (FZ) method, and the cubes were verified to be the near-{100}p Ni–Mn–Ga alloy. Various room temperature (RT) curing silicone rubbers were utilized as matrix materials. Furthermore, polystyrene foam particles (PFP) were used to provide pores, allowing a porous silicone rubber matrix. It was found that the elastic modulus of the silicone rubber was successfully reduced by introducing the PFP. Additionally, the magnetic field-induced martensite variant reorientation (MVR) was greatly enhanced by introducing a porous structure into the silicone rubber. The single-crystal Ni–Mn–Ga cube/porous silicone rubber composite materials are considered to be promising materials for applications in actuators.
- Open Access
- 22 July 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (14) , 8475
Fundamental Investigations of the Deformation Behavior of Single-Crystal Ni-Mn-Ga Alloys and Their Polymer Composites via the Introduction of Various Fields
To meet the great requirements of future technologies, such as robots, single-crystal (SC) Ni-Mn-Ga alloys and their composites were designed and investigated in this study. Ferromagnetic shape memory alloys (FSMAs) are promising materials for applications in high-speed actuators, which are core components of robots; however, there are some issues of embrittlement and small deformation strain. Therefore, in this work, we first prepared SC Ni-Mn-Ga alloys for fundamental investigations of the shape deformations under the application of different fields (e.g., compressive and magnetic fields). Second, the SC Ni-Mn-Ga alloys were integrated with polymers of epoxy resin or silicone rubber to solve the embrittlement problem. The obvious two-stage yielding and sudden intensifying of the magnetization both suggest martensite variant reorientation (MVR) under the compressive and magnetic fields, respectively. Micro-computed tomography (μCT) and an X-ray diffractometer were utilized for the observations of shape deformation brought about by the MVR of the SC Ni-Mn-Ga particles in the polymer matrix. Clear MVR and shape deformation could be found in the compressed composites.
- 22 July 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (14) , 8475
Open AccessFundamental Investigations of the Deformation Behavior of Single-Crystal Ni-Mn-Ga Alloys and Their Polymer Composites via the Introduction of Various Fields
To meet the great requirements of future technologies, such as robots, single-crystal (SC) Ni-Mn-Ga alloys and their composites were designed and investigated in this study. Ferromagnetic shape memory alloys (FSMAs) are promising materials for applications in high-speed actuators, which are core components of robots; however, there are some issues of embrittlement and small deformation strain. Therefore, in this work, we first prepared SC Ni-Mn-Ga alloys for fundamental investigations of the shape deformations under the application of different fields (e.g., compressive and magnetic fields). Second, the SC Ni-Mn-Ga alloys were integrated with polymers of epoxy resin or silicone rubber to solve the embrittlement problem. The obvious two-stage yielding and sudden intensifying of the magnetization both suggest martensite variant reorientation (MVR) under the compressive and magnetic fields, respectively. Micro-computed tomography (μCT) and an X-ray diffractometer were utilized for the observations of shape deformation brought about by the MVR of the SC Ni-Mn-Ga particles in the polymer matrix. Clear MVR and shape deformation could be found in the compressed composites.
- Open Access
Investigations of the Crystallographic Orientation on the Martensite Variant Reorientation of the Single-Crystal Ni-Mn-Ga Cube and Its Composites for Actuator Applications
High-speed actuators are greatly required in this decade due to the fast development of future technologies, such as Internet-of-Things (IoT) and robots. The ferromagnetic shape memory alloys (FSMAs), whose shape change could be driven by applying an external magnetic field, possess a rapid response. Hence, these materials are considered promising candidates for the applications of future technologies. Among the FSMAs, the Ni-Mn-Ga-based materials were chosen for their large shape deformation strain and appropriate phase transformation temperatures for near-room temperature applications. Nevertheless, it is widely known that both the intrinsic brittleness of the Ni-Mn-Ga alloy and the constraint of shape deformation strain due to the existence of grain boundaries in the polycrystal inhibit the applications. Therefore, various Ni-Mn-Ga-based composite materials were designed in this study, and their shape deformation behaviors induced by compressive or magnetic fields were examined by the in situ micro CT observations. In addition, the dependence of the martensite variant reorientation (MVR) on the crystallographic directions was also investigated. It was found that most of the MVRs are active within the magnetic field range applied in the regime of the p, p, and p of the single-crystal {100}p Ni-Mn-Ga cubes.
Open AccessInvestigations of the Crystallographic Orientation on the Martensite Variant Reorientation of the Single-Crystal Ni-Mn-Ga Cube and Its Composites for Actuator Applications
High-speed actuators are greatly required in this decade due to the fast development of future technologies, such as Internet-of-Things (IoT) and robots. The ferromagnetic shape memory alloys (FSMAs), whose shape change could be driven by applying an external magnetic field, possess a rapid response. Hence, these materials are considered promising candidates for the applications of future technologies. Among the FSMAs, the Ni-Mn-Ga-based materials were chosen for their large shape deformation strain and appropriate phase transformation temperatures for near-room temperature applications. Nevertheless, it is widely known that both the intrinsic brittleness of the Ni-Mn-Ga alloy and the constraint of shape deformation strain due to the existence of grain boundaries in the polycrystal inhibit the applications. Therefore, various Ni-Mn-Ga-based composite materials were designed in this study, and their shape deformation behaviors induced by compressive or magnetic fields were examined by the in situ micro CT observations. In addition, the dependence of the martensite variant reorientation (MVR) on the crystallographic directions was also investigated. It was found that most of the MVRs are active within the magnetic field range applied in the regime of the p, p, and p of the single-crystal {100}p Ni-Mn-Ga cubes.
- 11 September 2022
- Published by Elsevier in Journal of the Mechanics and Physics of Solids
- Vol. 169
Triplet condition: A new condition of supercompatibility between martensitic phases
- 11 September 2022
- Published by Elsevier in Journal of the Mechanics and Physics of Solids
- Vol. 169
Triplet condition: A new condition of supercompatibility between martensitic phases