TGTanveer Ahmed Gadhi

Tanveer Ahmed Gadhi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Tanveer Ahmed Gadhi has a total of 26 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Integrating technical and sustainability perspectives: anaerobic co-digestion from lab to pilot scale using textile wastewater sludge and cattle manure

    by Tanveer A. Gadhi, Najeebullah Channa, Rasool Bux Mahar, Sanam Bhatti, Bahadur Ali, Abdul Raheem, Francesca Demichelis, Tonia Tommasi, Francesca Stefania Freyria, Barbara Bonelli


  • Open Access

    Efficient and Rapid Combined Electrocoagulation–Filtration of Arsenic in Drinking Water

    by Najeebullah Channa, Tanveer A. Gadhi, Rasool Bux Mahar, Imran Ali, Sana Sajjad, Francesca S. Freyria, Barbara Bonelli, Sonke Widderich, Franz-Bernd Frechen

    Arsenic (As) contamination is a severe problem in drinking-water sources. This study designed and investigated a novel combined electrocoagulation–filtration (ECF) system to investigate As treatment and filtration in drinking water in collaboration with HANDS-Pakistan and Medico International, Germany. Two separate pilot-scale ECF systems were designed and developed with an electrocoagulation (EC) unit and a commercially available PAUL® filter configured with vertical flat-sheet ultra-low-pressure membranes of 0.04 µm pore size for the combined treatment and filtration of different As concentrations. Real drinking water at different As concentrations, i.e., 100, 200, and 300 μg/L were tested on one ECF system with EC electrodes of iron (Fe) and another system with aluminum (Al), at different treatment times (0, 5, 10, 20, 45, 60, 120, 180 min), at a fixed current density (12 mA/cm2) and water flow rate of 1 L/min. The initial results showed 99% As removal within 5 min with the combined ECF treatment for both electrodes of Fe and Al. In addition, the effect of ECF on different water-quality parameters and the ionic interference on ECF performance and As filtration were analyzed. The results showed the promising potential of combined ECF treatment and filtration for treating and purifying As.


  • Open Access

    The Identification of Selective Pathogenic Microbial Community Biofilms in Different Distribution Pipeline Materials and Their Disinfection Kinetics

    by Sanam Bhatti, Tanveer A. Gadhi, Rasool Bux Mahar, Imran Ali, Najeebullah Channa, Junaid Ahmed Kori, Barbara Bonelli

    Biofilms in water distribution lines strongly affect water safety as they are the main carriers of pathogens. The current study investigated the biofilm formation and identification of selected pathogens in different distribution pipeline materials and their disinfection method in an annular reactor (AR). Initially, the quality of the flowing water from each pipeline material was analyzed, i.e., pH, TDS, EC, turbidity, and salinity; then, the biofilm formation was monitored for each material, i.e., ABS, PC, PVC, PP, and HDPE. Further, the disinfection kinetics of biofilm at different chlorine doses, i.e., 0.5, 1.0, 1.5, and 2.0 mg/L, was investigated. The selected pathogens, i.e., E. coli, Pseudomonas, Shigella, Salmonella sp., and Vibrio sp. were identified in biofilms formed in different pipeline materials. The disinfection kinetics results showed that a chlorine dose of 2.0 mg/L was the most effective in disinfecting selected pathogens. Following the disinfection kinetics, it was observed that Salmonella sp. was disinfected within 7 days, whereas other pathogenic biofilms were disinfected within 14 days. The efficacy of chlorine disinfection was affected by the types of pipeline materials. The study outcomes could provide insights into biofilms’ disinfection method and the selection of suitable pipeline materials to ensure drinking water safety.


  • Open Access

    Insight on the Properties of Pumice Mineral for the Combined Adsorption Distillation of Membrane Reject Water

    by Tayyab A. Qureshi, Tanveer A. Gadhi, Danish A. Khokhar, Imran Ali, Najma Memon, Najeebullah Channa, Sikandar Bakhat, Tahir Rafique, Rasool Bux Mahar

    The current study evaluated the use of pumice, a volcanic mineral and common sand, in treating reverse osmosis membrane reject water (ROR) using a novel combined adsorption distillation (CAD) method. The CAD method is developed to separate the dissolved solids through adsorption distillation, i.e., leaving the vaporized distillate as freshwater and concentrated brine. The adsorption potential of pumice and sand was investigated at different adsorbent doses, i.e., 2, 5, and 10 g, and consecutive CAD adsorbent backwashing cycles. The improved results were achieved at a 10 g pumice dose. However, its adsorption efficiency declined in longer CAD cycles, i.e., due to the separated deposition of solids. After backwashing, the adsorbed and accumulated salts were slightly removed, and pumice adsorption capacity was maintained for up to 20 cycles of CAD. The properties of the pumice, i.e., before and after five CAD cycles and after backwashing, were characterized with scanning electron microscopic (SEM), elemental disruptive spectroscopy (EDS), and X-ray diffraction (XRD), which revealed that the porous structure of the pumice was completely accumulated with deposits of ionic salts, which were slightly washed away after backwashing, but accumulation remained continued in post-CAD cycles. The explored method revealed a high potential of pumice in water filtration.


  • Open Access

    Photocatalytic Denitrification of Nitrate Using Fe-TiO2-Coated Clay Filters

    by Tanveer A. Gadhi, Imtiaz Ali Bhurt, Tayyab A. Qureshi, Imran Ali, Anira Latif, Rasool Bux Mahar, Najeebullah Channa, Barbara Bonelli

    In this work, 3D-structured clay filters were prepared and coated with iron-doped titanium dioxide (Fe-TiO2) using 3D printing and sol–gel soaking and calcination techniques. Three-dimensional printing was employed to mold and shape the clay filters before annealing. The coated and uncoated filters were characterized for different properties, i.e., morphology, optical properties, and crystalline structure, using field emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectroscopy (EDS), UV/Vis diffused reflectance spectroscopy (DRS), and X-ray diffraction (XRD). The FESEM images show uniform coatings of round-shaped Fe-TiO2 on the tiny pore of the clay filter. The optical energy band gap of the obtained coating was around 2.8 eV, estimated by Tauc’s plot, compared with 3.2 eV of pristine anatase TiO2. The XRD spectra data processed through XRD software revealed the coatings of TiO2 on the filter surface with the obtained phase of anatase. The photocatalytic performance of bare and coated filters was initially tested for the degradation of indigo carmine (IC) dye and the obtained results suggested the photocatalytic degradation of IC dye by the Fe-TiO2 clay filter compared with the bare filter. Afterward, the denitrification of nitrate NO3 at various concentrations was performed using Fe-TiO2-coated clay filters and analyzing the total nitrogen (TN) analysis and reduction of NO3 to nitrite (NO2−), nitrogen monoxide (NO), and nitrogen gas (N2). The TN analysis revealed up to 81% denitrification efficiency of the 30 ppm NO3 solution with the photocatalytic response of the Fe-TiO2-coated filter. The results revealed that the Fe-TiO2-coated clay filter has a high potential for denitrification applications under natural sunlight.


  • Open Access

    Waste Heat and Wastewater Recovery in Textile Processing Industry: A Case Study of Adopted Practices

    by Tanveer Ahmed Gadhi, Imran Ali, Rasool Bux Mahar, Hubdar Ali Maitlo, Najeebullah Channa

    Textile wet processes dispose of huge amounts of water and energy in the form of hot wastewater and exhaust gas emissions. A significant amount of water and energy can be conserved by adopting various waste heat and water recovery methods, such as the use of heat exchanger, recycling hot wastewater, steam condensate, and cooling water recovery and reuse. In this study, various waste energy and water conservation methods are summarized to highlight their importance for water and energy conservation. For practical consideration, a detailed assessment of such practiced methods was done in one textile processing industry. The obtained results revealed that a high amount of energy and water could be conserved by adopting various waste heat and water recovery methods, with the advantage of reducing environmental pollution while minimizing the consumption of energy and water.