Srinivasan Vijayaraghavan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Srinivasan Vijayaraghavan has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Ramanujam Karthikeyan
Department of Mechanical Engineering, Birla Institute of Technology and Science, Pilani, Dubai Campus, Dubai International Academic City, Dubai, United Arab Emirates
2 shared publications B. Asaithambi
Annamalai University
1 shared publication- Balakrishnan Asaithambi
Annamalai University, India
1 shared publication G. Ganesan
Annamalai University
1 shared publication- Karthikeyan Thangavelu
Department of Mechanical Engineering, JJ College of Engineering and Technology, Tiruchirapalli, India
1 shared publication N. Mohamad Raffi
Department of Manufacturing Engineering, Annamalai University Annamalainagar - 608002, India
1 shared publication
Latest Publications
- Open Access
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 29 (4) , e20240600
Parameter optimization of laser cladding for Stelcar powder coatings on AZ61 magnesium alloy
The primary objective of this study is to enhance surface coating characteristics and reduce the dilution rate of AZ61 magnesium alloy coated with Stelcar alloy powder through laser cladding. A Taguchi (L16) orthogonal experimental design employed to analyze the effects of scanning speed, laser power, powder feed rate, and gas flow on wear volume, dilution rate and micro-hardness. Signal-to-noise ratios were calculated for each parameter to identify their individual effects on the responses. The findings indicated that powder feed rate predominantly influenced wear volume, accounting for 88.18% of its variation, while scanning speed has the highest influence on dilution rate (73.20%), and laser power significantly affected micro-hardness (84.60%). The optimized processing parameters were identified as a scanning speed of 11 mm/s, a laser power of 1.3 kW, a powder feed rate of 40 g/min, and a gas flow rate of 380 L/h. These parameters yielded a minimum wear volume of 0.8427 mm3, a dilution rate of 18.21%, and a maximum micro-hardness of 678.07 HV. This study utilized grey relational analysis to determine the optimum processing parameters, which simultaneously reduced wear volume, minimized dilution rate and enhanced micro-hardness.
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 29 (4) , e20240600
Open AccessParameter optimization of laser cladding for Stelcar powder coatings on AZ61 magnesium alloy
The primary objective of this study is to enhance surface coating characteristics and reduce the dilution rate of AZ61 magnesium alloy coated with Stelcar alloy powder through laser cladding. A Taguchi (L16) orthogonal experimental design employed to analyze the effects of scanning speed, laser power, powder feed rate, and gas flow on wear volume, dilution rate and micro-hardness. Signal-to-noise ratios were calculated for each parameter to identify their individual effects on the responses. The findings indicated that powder feed rate predominantly influenced wear volume, accounting for 88.18% of its variation, while scanning speed has the highest influence on dilution rate (73.20%), and laser power significantly affected micro-hardness (84.60%). The optimized processing parameters were identified as a scanning speed of 11 mm/s, a laser power of 1.3 kW, a powder feed rate of 40 g/min, and a gas flow rate of 380 L/h. These parameters yielded a minimum wear volume of 0.8427 mm3, a dilution rate of 18.21%, and a maximum micro-hardness of 678.07 HV. This study utilized grey relational analysis to determine the optimum processing parameters, which simultaneously reduced wear volume, minimized dilution rate and enhanced micro-hardness.
- 26 April 2010
- Published by Springer Nature in Metals and Materials International
- Vol. 16 (2) , 205-212
Comparative study on the wear behavior of long and short glass fiber reinforced plastics
- 26 April 2010
- Published by Springer Nature in Metals and Materials International
- Vol. 16 (2) , 205-212
Comparative study on the wear behavior of long and short glass fiber reinforced plastics
- 14 April 2010
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 29 (19) , 3006-3015
Characterisitcs of Al2O3 Nano-Particle Filled GFRP Composites Using Wear Maps
In this study, glass fiber reinforced plastic (GFRP) filled with different volume fraction (1, 2 & 3%) of nano-Al2O3 particles are tested for their tribological behavior. The wear tests are conducted for different sliding velocities ranging from 0.312 to 2.512 m/s and normal force ranging from 4.91 to 24.71 N. Different wear mechanisms are identified through scanning electron microscope (SEM). Wear maps are drawn by taking sliding velocity on x-axis and normal force on y-axis. The wear maps are utilized to study the dominance of particular wear mechanism that dominates a particular wear regime. Out of three materials discussed, GFRP filled with 3% nano alumina (GFRP3) exhibits better wear resistance than the other materials used in this study.
- 14 April 2010
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 29 (19) , 3006-3015
Characterisitcs of Al2O3 Nano-Particle Filled GFRP Composites Using Wear Maps
In this study, glass fiber reinforced plastic (GFRP) filled with different volume fraction (1, 2 & 3%) of nano-Al2O3 particles are tested for their tribological behavior. The wear tests are conducted for different sliding velocities ranging from 0.312 to 2.512 m/s and normal force ranging from 4.91 to 24.71 N. Different wear mechanisms are identified through scanning electron microscope (SEM). Wear maps are drawn by taking sliding velocity on x-axis and normal force on y-axis. The wear maps are utilized to study the dominance of particular wear mechanism that dominates a particular wear regime. Out of three materials discussed, GFRP filled with 3% nano alumina (GFRP3) exhibits better wear resistance than the other materials used in this study.