Tobias Reiter
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Tobias Reiter has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Lado Filipovic
TU Wien
4 shared publications Xaver Klemenschits
TU Wien, Inst Microelect, Gusshausstr 27-29, A-1040 Vienna, Austria
3 shared publicationsAndreas Hössinger
2 shared publicationsFrâncio Rodrigues
2 shared publicationsJosef Weinbub
2 shared publicationsLado Filipovic
2 shared publications
Latest Publications
- Open Access
- 18 June 2026
- Published by Springer Nature in Journal of Computational Electronics
- Vol. 25 (4) , 132
Shape-aware dissimilarity measures for process TCAD model calibration
Traditional calibration of semiconductor TCAD models for topography modifying processes often relies on matching critical dimensions (CDs). This approach is prone to subjective measurement and fails to capture overall profile shape differences, thereby limiting the accuracy and effectiveness of model optimization. In this work, we address this limitation by adapting computer vision techniques for TCAD model calibration. We comprehensively evaluate several shape dissimilarity measures (SDM): the established Chamfer Distance (CHD) and two novel level-set-based measures, the Area Difference (AD) and the Sparse Field Distance (SFD). Through a rigorous computational case study, testing for sensitivity, robustness, and efficiency, we demonstrate that SFD and CHD significantly outperform traditional CD matching and area-based methods for semiconductor profile comparison derived from a representative scanning electron microscopy (SEM) image. These standardized SDMs are crucial for leveraging emerging large-scale electron microscopy datasets and enabling robust, machine learning-driven model development.
- 18 June 2026
- Published by Springer Nature in Journal of Computational Electronics
- Vol. 25 (4) , 132
Open AccessShape-aware dissimilarity measures for process TCAD model calibration
Traditional calibration of semiconductor TCAD models for topography modifying processes often relies on matching critical dimensions (CDs). This approach is prone to subjective measurement and fails to capture overall profile shape differences, thereby limiting the accuracy and effectiveness of model optimization. In this work, we address this limitation by adapting computer vision techniques for TCAD model calibration. We comprehensively evaluate several shape dissimilarity measures (SDM): the established Chamfer Distance (CHD) and two novel level-set-based measures, the Area Difference (AD) and the Sparse Field Distance (SFD). Through a rigorous computational case study, testing for sensitivity, robustness, and efficiency, we demonstrate that SFD and CHD significantly outperform traditional CD matching and area-based methods for semiconductor profile comparison derived from a representative scanning electron microscopy (SEM) image. These standardized SDMs are crucial for leveraging emerging large-scale electron microscopy datasets and enabling robust, machine learning-driven model development.
- Open Access
- 2 November 2023
- Published by Elsevier in Solid-State Electronics
- Vol. 211
Modeling the impact of incomplete conformality during atomic layer processing
- 2 November 2023
- Published by Elsevier in Solid-State Electronics
- Vol. 211
Open AccessModeling the impact of incomplete conformality during atomic layer processing
- 4 August 2023
- Published by American Physical Society (APS) in Physical Review A
- Vol. 108 (2) , 023504
Tractor beams with optimal pulling force using structured waves
Moving objects with optical or acoustical waves are topics both of fundamental interest and of importance for a range of practical applications. One particularly intriguing example is the tractor beam, which pulls an object toward the wave's source, in opposition to the wave's momentum. In this study, we introduce a protocol that enables the identification of wave states that produce the optimal tractor force for arbitrary objects. Our method relies solely on the solution of a simple eigenvalue problem involving the system's measurable scattering matrix. Using numerical simulations, we demonstrate the efficacy of this wavefront shaping protocol for a representative set of different targets. Moreover, we show that the diffractive nature of waves enables the possibility of a tractor beam that works even for targets where a geometric optics approach fails to explain the pulling forces.
- 4 August 2023
- Published by American Physical Society (APS) in Physical Review A
- Vol. 108 (2) , 023504
Tractor beams with optimal pulling force using structured waves
Moving objects with optical or acoustical waves are topics both of fundamental interest and of importance for a range of practical applications. One particularly intriguing example is the tractor beam, which pulls an object toward the wave's source, in opposition to the wave's momentum. In this study, we introduce a protocol that enables the identification of wave states that produce the optimal tractor force for arbitrary objects. Our method relies solely on the solution of a simple eigenvalue problem involving the system's measurable scattering matrix. Using numerical simulations, we demonstrate the efficacy of this wavefront shaping protocol for a representative set of different targets. Moreover, we show that the diffractive nature of waves enables the possibility of a tractor beam that works even for targets where a geometric optics approach fails to explain the pulling forces.
- Open Access
- 25 July 2023
- Published by American Physical Society (APS) in Physical Review Letters
- Vol. 131 (4) , 043601
Triggered Superradiance and Spin Inversion Storage in a Hybrid Quantum System
We study the superradiant emission of an inverted spin ensemble strongly coupled to a superconducting cavity. After fast inversion, we detune the spins from the cavity and store the inversion for tens of milliseconds, during which the remaining transverse spin components disappear. Switching back on resonance enables us to study the onset of superradiance. A weak trigger pulse of a few hundred photons shifts the superradiant burst to earlier times and imprints its phase onto the emitted radiation. For long hold times, the inversion decreases below the threshold for spontaneous superradiance. There, the energy stored in the ensemble can be used to amplify microwave pulses passing through the cavity.
- 25 July 2023
- Published by American Physical Society (APS) in Physical Review Letters
- Vol. 131 (4) , 043601
Open AccessTriggered Superradiance and Spin Inversion Storage in a Hybrid Quantum System
We study the superradiant emission of an inverted spin ensemble strongly coupled to a superconducting cavity. After fast inversion, we detune the spins from the cavity and store the inversion for tens of milliseconds, during which the remaining transverse spin components disappear. Switching back on resonance enables us to study the onset of superradiance. A weak trigger pulse of a few hundred photons shifts the superradiant burst to earlier times and imprints its phase onto the emitted radiation. For long hold times, the inversion decreases below the threshold for spontaneous superradiance. There, the energy stored in the ensemble can be used to amplify microwave pulses passing through the cavity.
- Open Access
- 16 March 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (3) , 665
Effect of Mask Geometry Variation on Plasma Etching Profiles
It is becoming quite evident that, when it comes to the further scaling of advanced node transistors, increasing the flash memory storage capacity, and enabling the on-chip integration of multiple functionalities, “there’s plenty of room at the top”. The fabrication of vertical, three-dimensional features as enablers of these advanced technologies in semiconductor devices is commonly achieved using plasma etching. Of the available plasma chemistries, SF6/O2 is one of the most frequently applied. Therefore, having a predictive model for this process is indispensable in the design cycle of semiconductor devices. In this work, we implement a physical SF6/O2 plasma etching model which is based on Langmuir adsorption and is calibrated and validated to published equipment parameters. The model is implemented in a broadly applicable in-house process simulator ViennaPS, which includes Monte Carlo ray tracing and a level set-based surface description. We then use the model to study the impact of the mask geometry on the feature profile, when etching through circular and rectangular mask openings. The resulting dimensions of a cylindrical hole or trench can vary greatly due to variations in mask properties, such as its etch rate, taper angle, faceting, and thickness. The peak depth for both the etched cylindrical hole and trench occurs when the mask is tapered at about 0.5°, and this peak shifts towards higher angles in the case of high passivation effects during the etch. The minimum bowing occurs at the peak depth, and it increases with an increasing taper angle. For thin-mask faceting, it is observed that the maximum depth increases with an increasing taper angle, without a significant variation between thin masks. Bowing is observed to be at a maximum when the mask taper angle is between 15° and 20°. Finally, the mask etch rate variation, describing the etching of different mask materials, shows that, when a significant portion of the mask is etched away, there is a notable increase in vertical etching and a decrease in bowing. Ultimately, the implemented model and framework are useful for providing a guideline for mask design rules.
- 16 March 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (3) , 665
Open AccessEffect of Mask Geometry Variation on Plasma Etching Profiles
It is becoming quite evident that, when it comes to the further scaling of advanced node transistors, increasing the flash memory storage capacity, and enabling the on-chip integration of multiple functionalities, “there’s plenty of room at the top”. The fabrication of vertical, three-dimensional features as enablers of these advanced technologies in semiconductor devices is commonly achieved using plasma etching. Of the available plasma chemistries, SF6/O2 is one of the most frequently applied. Therefore, having a predictive model for this process is indispensable in the design cycle of semiconductor devices. In this work, we implement a physical SF6/O2 plasma etching model which is based on Langmuir adsorption and is calibrated and validated to published equipment parameters. The model is implemented in a broadly applicable in-house process simulator ViennaPS, which includes Monte Carlo ray tracing and a level set-based surface description. We then use the model to study the impact of the mask geometry on the feature profile, when etching through circular and rectangular mask openings. The resulting dimensions of a cylindrical hole or trench can vary greatly due to variations in mask properties, such as its etch rate, taper angle, faceting, and thickness. The peak depth for both the etched cylindrical hole and trench occurs when the mask is tapered at about 0.5°, and this peak shifts towards higher angles in the case of high passivation effects during the etch. The minimum bowing occurs at the peak depth, and it increases with an increasing taper angle. For thin-mask faceting, it is observed that the maximum depth increases with an increasing taper angle, without a significant variation between thin masks. Bowing is observed to be at a maximum when the mask taper angle is between 15° and 20°. Finally, the mask etch rate variation, describing the etching of different mask materials, shows that, when a significant portion of the mask is etched away, there is a notable increase in vertical etching and a decrease in bowing. Ultimately, the implemented model and framework are useful for providing a guideline for mask design rules.
- Open Access
- 28 December 2022
- Published by Elsevier in Solid-State Electronics
- Vol. 201
Modeling incomplete conformality during atomic layer deposition in high aspect ratio structures
- 28 December 2022
- Published by Elsevier in Solid-State Electronics
- Vol. 201
Open AccessModeling incomplete conformality during atomic layer deposition in high aspect ratio structures
- Open Access
- 21 November 2022
- Published by Elsevier in Solid-State Electronics
- Vol. 199
DTCO flow for air spacer generation and its impact on power and performance at N7
- 21 November 2022
- Published by Elsevier in Solid-State Electronics
- Vol. 199
Open AccessDTCO flow for air spacer generation and its impact on power and performance at N7
- 1 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Impact of High-Aspect-Ratio Etching Damage on Selective Epitaxial Silicon Growth in 3D NAND Flash Memory
A physical process model for inductive plasma dry etching is presented and applied to simulate vertical channel hole etching, a critical fabrication step in modern 3D NAND flash memory. A specialized advection algorithm is subsequently applied to simulate the selective epitaxial growth (SEG) of silicon on the bottom source line. The induced etching damage on the bottom silicon substrate, which is included in the etching model, is shown to heavily reduce the quality of the SEG. The removal of this damaged layer is shown to result in highly crystalline epitaxially grown silicon.
- 1 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Impact of High-Aspect-Ratio Etching Damage on Selective Epitaxial Silicon Growth in 3D NAND Flash Memory
A physical process model for inductive plasma dry etching is presented and applied to simulate vertical channel hole etching, a critical fabrication step in modern 3D NAND flash memory. A specialized advection algorithm is subsequently applied to simulate the selective epitaxial growth (SEG) of silicon on the bottom source line. The induced etching damage on the bottom silicon substrate, which is included in the etching model, is shown to heavily reduce the quality of the SEG. The removal of this damaged layer is shown to result in highly crystalline epitaxially grown silicon.