Jonathan Schanner
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jonathan Schanner has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Alexander Hasse
Institut für Konstruktions- und Antriebstechnik, Fakultät für Maschinenbau, Technische Universität Chemnitz, Chemnitz, Germany
3 shared publications - Alexander Hasse
Institute for Engineering Design and Drive Technology, University of Technology Chemnitz, Chemnitz, Germany
2 shared publications - Andreas Schubert
Micromanufacturing Technology, Faculty of Mechanical Engineering, Chemnitz University of Technology, Chemnitz, Germany
2 shared publications Alexander Hasse
1 shared publicationAndreas Schubert
1 shared publication- Denny Knabner
Institute of Design Engineering and Drive Technology, Technische Universität Chemnitz, Chemnitz, Germany
1 shared publication
Latest Publications
- Open Access
- 22 July 2026
- Published by Elsevier in SSRN Electronic Journal
Influence of fretting and creeping kinematics on friction and wear of flat-on-flat steel–cast iron contacts
Machine components subjected to dynamic loading, such as bearing seats, inevitably experience micro‐sliding that can lead to surface damage and eventual failure. This micro‐sliding manifests in two fundamentally different kinematic modes: oscillatory motion (fretting) and unidirectional, incremental motion, commonly referred to as creeping, which is driven by shear stresses from rolling elements or external forces. While many analysis of wear and friction are present for fretting motion, the effects of creeping on these phenomenons are poorly understood. This study experimentally compares fretting and creeping motion on annular steel-cast iron flat-on-flat contacts, using accumulated frictional work as a common basis for comparison. The assumption of an indiscriminate Archard wear coefficient is contradicted by linking the observed surface damage to distinct wear modes: adhesion‐dominated for fretting and abrasion‐dominated for creeping. Creeping initiates severe abrasive damage at lower frictional work than fretting, producing a wear volume roughly 50 times larger. This behaviour is also visible in the corresponding coefficient of friction (COF) evolution curves: the fretting COF rises to approximately 1.0 before dropping of and stabalizing, whereas the creeping COF scatters around 0.6 without stabilizing. These results show, that a differentiation in the underlying kinematics is necessary when not analysing surface damage and COF evolution in dynamically loaded contacts.
- 22 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessInfluence of fretting and creeping kinematics on friction and wear of flat-on-flat steel–cast iron contacts
Machine components subjected to dynamic loading, such as bearing seats, inevitably experience micro‐sliding that can lead to surface damage and eventual failure. This micro‐sliding manifests in two fundamentally different kinematic modes: oscillatory motion (fretting) and unidirectional, incremental motion, commonly referred to as creeping, which is driven by shear stresses from rolling elements or external forces. While many analysis of wear and friction are present for fretting motion, the effects of creeping on these phenomenons are poorly understood. This study experimentally compares fretting and creeping motion on annular steel-cast iron flat-on-flat contacts, using accumulated frictional work as a common basis for comparison. The assumption of an indiscriminate Archard wear coefficient is contradicted by linking the observed surface damage to distinct wear modes: adhesion‐dominated for fretting and abrasion‐dominated for creeping. Creeping initiates severe abrasive damage at lower frictional work than fretting, producing a wear volume roughly 50 times larger. This behaviour is also visible in the corresponding coefficient of friction (COF) evolution curves: the fretting COF rises to approximately 1.0 before dropping of and stabalizing, whereas the creeping COF scatters around 0.6 without stabilizing. These results show, that a differentiation in the underlying kinematics is necessary when not analysing surface damage and COF evolution in dynamically loaded contacts.
- Open Access
- 26 June 2025
- Published by Elsevier in Tribology International
- Vol. 212
Surfaces microstructured by turn-milling: Insights in contact mechanics and coefficient of friction from experimental, numerical and theoretical analyses
- 26 June 2025
- Published by Elsevier in Tribology International
- Vol. 212
Open AccessSurfaces microstructured by turn-milling: Insights in contact mechanics and coefficient of friction from experimental, numerical and theoretical analyses
- Open Access
- 27 February 2025
- Published by Springer Nature in Forschung im Ingenieurwesen
- Vol. 89 (1) , 1-10
Dynamic embedding process of friction enhancing hard particles in frictional connections
The torque transmission capacity of frictional connections, commonly used in wind turbine drive trains, is heavily influenced by the coefficient of friction between contacting surfaces. To improve performance, friction-enhancing techniques like hard particle systems and coatings are employed to increase the coefficient of friction. Hard particles enhance deformative friction through embedding and micro-interlocking with the base material. Despite efforts to minimize them, dynamic loads can still result in micro-slip movements that alter the frictional behavior of the joint. This research investigates the effects of alternating loads, below the sliding limit, on the embedding process of diamond particles. Through simulations using an elasto-plastic finite element (FE) model, the study compares slip amplitude and transmittable torque under dynamic loading conditions with reference pairings and quasi-static torsion tests. Findings reveal that dynamic pre-loading significantly influences frictional characteristics, boosting torque transmission. The micro-slip motion observed in FE simulations highlights how the embedding process of hard particles during dynamic loading leads to increased frictional resistance, with a clear correlation between particle indentation depth and the resulting frictional slip behavior.
- 27 February 2025
- Published by Springer Nature in Forschung im Ingenieurwesen
- Vol. 89 (1) , 1-10
Open AccessDynamic embedding process of friction enhancing hard particles in frictional connections
The torque transmission capacity of frictional connections, commonly used in wind turbine drive trains, is heavily influenced by the coefficient of friction between contacting surfaces. To improve performance, friction-enhancing techniques like hard particle systems and coatings are employed to increase the coefficient of friction. Hard particles enhance deformative friction through embedding and micro-interlocking with the base material. Despite efforts to minimize them, dynamic loads can still result in micro-slip movements that alter the frictional behavior of the joint. This research investigates the effects of alternating loads, below the sliding limit, on the embedding process of diamond particles. Through simulations using an elasto-plastic finite element (FE) model, the study compares slip amplitude and transmittable torque under dynamic loading conditions with reference pairings and quasi-static torsion tests. Findings reveal that dynamic pre-loading significantly influences frictional characteristics, boosting torque transmission. The micro-slip motion observed in FE simulations highlights how the embedding process of hard particles during dynamic loading leads to increased frictional resistance, with a clear correlation between particle indentation depth and the resulting frictional slip behavior.
- Open Access
- 28 October 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (11) , 371
Transferability of Model-Based Static Coefficient of Friction
The accurate determination of static coefficients of friction (COFs) is crucial in engineering design, yet standard reference values often show considerable variability. As a result, engineers frequently need to perform experimental COF measurements to ensure the reliable transferability of model-based COFs to real-world components. However, the effectiveness of cost-efficient laboratory tests, typically conducted on standardized samples, in reflecting actual component performance is often questioned as it is not trivial to transfer and scale the tribosystem. This study addresses this issue by conducting friction coefficient experiments on interference fits and flange connections, comparing the results with laboratory-based COF tests. The findings reveal a strong correlation when the tribological conditions of the real assembly are replicated in the lab. This research offers a method to enhance the accuracy and transferability of COF values from lab tests to practical applications, providing engineers with a more reliable approach to friction testing.
- 28 October 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (11) , 371
Open AccessTransferability of Model-Based Static Coefficient of Friction
The accurate determination of static coefficients of friction (COFs) is crucial in engineering design, yet standard reference values often show considerable variability. As a result, engineers frequently need to perform experimental COF measurements to ensure the reliable transferability of model-based COFs to real-world components. However, the effectiveness of cost-efficient laboratory tests, typically conducted on standardized samples, in reflecting actual component performance is often questioned as it is not trivial to transfer and scale the tribosystem. This study addresses this issue by conducting friction coefficient experiments on interference fits and flange connections, comparing the results with laboratory-based COF tests. The findings reveal a strong correlation when the tribological conditions of the real assembly are replicated in the lab. This research offers a method to enhance the accuracy and transferability of COF values from lab tests to practical applications, providing engineers with a more reliable approach to friction testing.
- Open Access
- 15 November 2022
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 6 (6) , 143
Investigating the Friction Behavior of Turn-Milled High Friction Surface Microstructures under Different Tribological Influence Factors
The coefficient of friction (COF) is an important parameter for mechanical engineers to consider when designing frictional connections. Previous work has shown that a surface microstructuring of the harder friction partner leads to a significant increase in the COF. However, the impact of the changes in the tribological system on the COF are not known in detail. In this study, the tribological influence factors such as the nominal surface pressure, the material pairing, lubrication, and the surface properties of the counterbody are investigated. Microstructuring is applied by turn-milling of an annular contact surface of cylindrical specimens. A torsional test bench is used to measure the torque depending on the displacement of the two specimens, thus enabling the determination of the COF. All tests with the microstructured specimens result in higher COF than the reference test with unstructured samples. The manufacturing process of the counterbody surface, the nominal surface pressure, and the materials in contact have a significant influence on the COF. While lubrication reduces friction in the case of unstructured specimens, the COF does not change significantly for microstructured samples. This proves that the deformative friction component dominates over the adhesive. Microstructuring the harder friction partner increases the transmittable torque in frictional connections and reduces the sensitivity towards possible contamination with lubricants.
- 15 November 2022
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 6 (6) , 143
Open AccessInvestigating the Friction Behavior of Turn-Milled High Friction Surface Microstructures under Different Tribological Influence Factors
The coefficient of friction (COF) is an important parameter for mechanical engineers to consider when designing frictional connections. Previous work has shown that a surface microstructuring of the harder friction partner leads to a significant increase in the COF. However, the impact of the changes in the tribological system on the COF are not known in detail. In this study, the tribological influence factors such as the nominal surface pressure, the material pairing, lubrication, and the surface properties of the counterbody are investigated. Microstructuring is applied by turn-milling of an annular contact surface of cylindrical specimens. A torsional test bench is used to measure the torque depending on the displacement of the two specimens, thus enabling the determination of the COF. All tests with the microstructured specimens result in higher COF than the reference test with unstructured samples. The manufacturing process of the counterbody surface, the nominal surface pressure, and the materials in contact have a significant influence on the COF. While lubrication reduces friction in the case of unstructured specimens, the COF does not change significantly for microstructured samples. This proves that the deformative friction component dominates over the adhesive. Microstructuring the harder friction partner increases the transmittable torque in frictional connections and reduces the sensitivity towards possible contamination with lubricants.
- 20 June 2022
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 80, 504-514
Generation of friction-increasing surfaces by turn-milling
- 20 June 2022
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 80, 504-514
Generation of friction-increasing surfaces by turn-milling