Sofya D. Afonnikova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sofya D. Afonnikova has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
- Alexey Anatolievich Vedyagin
Boreskov Institute of Catalysis SB RAS, Novosibirsk, Russia
9 shared publications - Ilya Vladimirovich Mishakov
Boreskov Institute of Catalysis, Siberian Branch, Russian Academy of Sciences, Novosibirsk, Russia
8 shared publications - Yury Bauman
Boreskov Institute of Catalysis, Siberian Branch, Russian Academy of Sciences, Novosibirsk, Russia
8 shared publications - Yuriy V. Shubin
Nikolaev Institute of Inorganic Chemistry SB RAS, Lavrentieva Av. 3, 630090 Novosibirsk, Russia
7 shared publications - Anton A. Popov
Nikolaev Institute of Inorganic Chemistry, Siberian Branch, Russian Academy of Sciences, Novosibirsk, Russia
4 shared publications - Pavel E. Plyusnin
Nikolaev Institute of Inorganic Chemistry SB RAS, 3, Acad. Lavrentiev Ave., Novosibirsk 630090, Russia
4 shared publications
Latest Publications
- 4 January 2025
- Published by Elsevier in Materials Letters
- Vol. 383
First observation of nickel nitrides during the interaction of NiCu alloys with melamine and g-C3N4 in a closed volume
- 4 January 2025
- Published by Elsevier in Materials Letters
- Vol. 383
First observation of nickel nitrides during the interaction of NiCu alloys with melamine and g-C3N4 in a closed volume
- 1 June 2024
- Published by Pleiades Publishing Ltd in Russian Journal of General Chemistry
- Vol. 94 (6) , 1322-1333
Synthesis of Microdispersed Ni1–xRux Alloys for Obtaining Metal-Carbon Nanocomposites in the Mode of Carbon Erosion
Using the method of reductive thermolysis of two-component precursors, a series of microdispersed alloys Ni1–xRux containing up to 10 at % ruthenium was obtained. The effect of ruthenium content in the alloy on its activity in the catalytic pyrolysis of a mixture of C2–C4 hydrocarbons to produce carbon nanofibers (CNF) was studied. Using the Ni0.98Ru0.02 sample as an example, the early stage of carbon erosion, leading to the disintegration of the alloy and to the formation of active particles, was studied in detail. The obtained alloys were used for the synthesis of metal-carbon nanocomposites Ni1–xRux@CNF, which are promising materials for solving applied problems.
- 1 June 2024
- Published by Pleiades Publishing Ltd in Russian Journal of General Chemistry
- Vol. 94 (6) , 1322-1333
Synthesis of Microdispersed Ni1–xRux Alloys for Obtaining Metal-Carbon Nanocomposites in the Mode of Carbon Erosion
Using the method of reductive thermolysis of two-component precursors, a series of microdispersed alloys Ni1–xRux containing up to 10 at % ruthenium was obtained. The effect of ruthenium content in the alloy on its activity in the catalytic pyrolysis of a mixture of C2–C4 hydrocarbons to produce carbon nanofibers (CNF) was studied. Using the Ni0.98Ru0.02 sample as an example, the early stage of carbon erosion, leading to the disintegration of the alloy and to the formation of active particles, was studied in detail. The obtained alloys were used for the synthesis of metal-carbon nanocomposites Ni1–xRux@CNF, which are promising materials for solving applied problems.
- 13 December 2023
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 314
Synthesis of Mo2C-based material in DC arc discharge plasma under ambient air conditions
- 13 December 2023
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 314
Synthesis of Mo2C-based material in DC arc discharge plasma under ambient air conditions
- 13 December 2023
- Published by Springer Nature in Reaction Kinetics, Mechanisms and Catalysis
- Vol. 137 (1) , 323-338
Synthesis and catalytic activity of porous Fe–Pd alloys in the decomposition of C2–C4 hydrocarbons
- 13 December 2023
- Published by Springer Nature in Reaction Kinetics, Mechanisms and Catalysis
- Vol. 137 (1) , 323-338
Synthesis and catalytic activity of porous Fe–Pd alloys in the decomposition of C2–C4 hydrocarbons
- Open Access
Effect of Cu on Performance of Self-Dispersing Ni-Catalyst in Production of Carbon Nanofibers from Ethylene
The development of effective catalysts for the pyrolysis of light hydrocarbons with the production of carbon nanomaterials represents a relevant direction. In the present work, the influence of copper addition on performance of a self-dispersed Ni-catalyst and structural features of the obtained carbon nanofibers (CNFs) was studied. The precursors of Ni and Ni-Cu catalysts were prepared by activation of metal powders in a planetary mill. During contact with the C2H4/H2 reaction mixture, a rapid disintegration of the catalysts with the formation of active particles catalyzing the growth of CNFs has occurred. The kinetics of CNF accumulation during ethylene decomposition on Ni- and Ni-Cu catalysts was studied. The effect of temperature on catalytic performance was explored and it was shown that introduction of copper promotes 1.5–2-fold increase in CNFs yield in the range of 525–600 °C; the maximum CNFs yield (100 g/gcat and above, for 30-min reaction) is reached on Ni-Cu-catalyst at 575–600 °C. A comparative analysis of the morphology and structure of CNF was carried out using electron microscopy methods. The growth mechanism of carbon filaments in the shape of “railway crossties” on large nickel crystals (d > 250 nm) was proposed. It was found that the addition of copper leads to a decrease in the bulk density of the carbon product from 40–60 to 25–30 g/L (at T = 550–600 °C). According to the low-temperature nitrogen adsorption data, specific surface area (SSA) of CNF samples (at T < 600 °C) lies in the range of 110–140 m2/g, regardless of the catalyst composition; at T = 600 °C the introduction of copper contributed to an increase in the specific surface of CNF by 100 m2/g.
Open AccessEffect of Cu on Performance of Self-Dispersing Ni-Catalyst in Production of Carbon Nanofibers from Ethylene
The development of effective catalysts for the pyrolysis of light hydrocarbons with the production of carbon nanomaterials represents a relevant direction. In the present work, the influence of copper addition on performance of a self-dispersed Ni-catalyst and structural features of the obtained carbon nanofibers (CNFs) was studied. The precursors of Ni and Ni-Cu catalysts were prepared by activation of metal powders in a planetary mill. During contact with the C2H4/H2 reaction mixture, a rapid disintegration of the catalysts with the formation of active particles catalyzing the growth of CNFs has occurred. The kinetics of CNF accumulation during ethylene decomposition on Ni- and Ni-Cu catalysts was studied. The effect of temperature on catalytic performance was explored and it was shown that introduction of copper promotes 1.5–2-fold increase in CNFs yield in the range of 525–600 °C; the maximum CNFs yield (100 g/gcat and above, for 30-min reaction) is reached on Ni-Cu-catalyst at 575–600 °C. A comparative analysis of the morphology and structure of CNF was carried out using electron microscopy methods. The growth mechanism of carbon filaments in the shape of “railway crossties” on large nickel crystals (d > 250 nm) was proposed. It was found that the addition of copper leads to a decrease in the bulk density of the carbon product from 40–60 to 25–30 g/L (at T = 550–600 °C). According to the low-temperature nitrogen adsorption data, specific surface area (SSA) of CNF samples (at T < 600 °C) lies in the range of 110–140 m2/g, regardless of the catalyst composition; at T = 600 °C the introduction of copper contributed to an increase in the specific surface of CNF by 100 m2/g.
- Open Access
- 6 June 2023
- Published by MDPI AG in Journal of Composites Science
- Vol. 7 (6) , 238
Synthesis of Ni-Cu-CNF Composite Materials via Carbon Erosion of Ni-Cu Bulk Alloys Prepared by Mechanochemical Alloying
The unique physical and chemical properties of composite materials based on carbon nanofibers (CNFs) makes them attractive to scientists and manufacturers. One promising method to produce CNFs is catalytic chemical vapor deposition (CCVD). In the present work, a method based on carbon erosion (CE) of bulk microdispersed Ni-Cu alloys has been proposed to prepare efficient catalysts for the synthesis of CNF-based composites. The initial Ni-Cu alloys were obtained by mechanochemical alloying (MCA) of metallic powders in a planetary mill. The effect of MCA duration on the phase composition of Ni-Cu samples was studied by X-ray diffraction analysis and temperature-programmed reduction in hydrogen. It has been also revealed that, during such stages as heating, reduction, and short-term exposure to the reaction mixture (C2H4/H2/Ar) at 550 °C, the formation of a Ni-based solid solution from the initial Ni-Cu alloys takes place. The early stages of the CE process were monitored by transmission electron microscopy combined with energy-dispersive X-Ray analysis. It was found that the composition of the catalytic particles is identical to that of the initial alloy. The morphological and structural features of the prepared Ni-Cu-CNF composites were studied by scanning and transmission electron microscopies. The textural characteristics of the composites were found to be dependent on the reaction time.
- 6 June 2023
- Published by MDPI AG in Journal of Composites Science
- Vol. 7 (6) , 238
Open AccessSynthesis of Ni-Cu-CNF Composite Materials via Carbon Erosion of Ni-Cu Bulk Alloys Prepared by Mechanochemical Alloying
The unique physical and chemical properties of composite materials based on carbon nanofibers (CNFs) makes them attractive to scientists and manufacturers. One promising method to produce CNFs is catalytic chemical vapor deposition (CCVD). In the present work, a method based on carbon erosion (CE) of bulk microdispersed Ni-Cu alloys has been proposed to prepare efficient catalysts for the synthesis of CNF-based composites. The initial Ni-Cu alloys were obtained by mechanochemical alloying (MCA) of metallic powders in a planetary mill. The effect of MCA duration on the phase composition of Ni-Cu samples was studied by X-ray diffraction analysis and temperature-programmed reduction in hydrogen. It has been also revealed that, during such stages as heating, reduction, and short-term exposure to the reaction mixture (C2H4/H2/Ar) at 550 °C, the formation of a Ni-based solid solution from the initial Ni-Cu alloys takes place. The early stages of the CE process were monitored by transmission electron microscopy combined with energy-dispersive X-Ray analysis. It was found that the composition of the catalytic particles is identical to that of the initial alloy. The morphological and structural features of the prepared Ni-Cu-CNF composites were studied by scanning and transmission electron microscopies. The textural characteristics of the composites were found to be dependent on the reaction time.
- Open Access
Pt1−xNix Alloy Nanoparticles Embedded in Self-Grown Carbon Nanofibers: Synthesis, Properties and Catalytic Activity in HER
The development of new heterogeneous Pt-containing catalysts has retained its relevance over the past decades. The present paper describes the method to produce metal–carbon composites, Pt1−xNix/CNF, with an adjustable Pt/Ni ratio. The composites represent Pt1−xNix (x = 0.0–1.0) nanoparticles embedded within a structure of carbon nanofibers (CNF). The synthesis of the composites is based on a spontaneous disintegration of Pt1−xNix alloys in an ethylene-containing atmosphere with the formation of CNF. The initial Pt1−xNix alloys were prepared by thermolysis of multicomponent precursors. They possess a porous structure formed by fragments of 100–200 nm. As was shown by X-ray diffraction analysis, the crystal structure of the alloys containing 0–30 and 60–100 at.% Ni corresponds to a fcc lattice based on platinum (Fm-3m), while the Pt0.50Ni0.50 sample is an intermetallic compound with the tetragonal structure (P4/mmm). The impact of the Ni content in the Pt1−xNix samples on their activity in ethylene decomposition was studied as well. As was revealed, the efficiency of Pt1−xNix alloys in this process increases with the rise of Ni concentration. The composite samples were examined in an electrochemical hydrogen evolution reaction. The synthesized Pt1-xNix/CNF composites demonstrated superior activity if compared with the Pt/Vulcan commercial catalyst.
Open AccessPt1−xNix Alloy Nanoparticles Embedded in Self-Grown Carbon Nanofibers: Synthesis, Properties and Catalytic Activity in HER
The development of new heterogeneous Pt-containing catalysts has retained its relevance over the past decades. The present paper describes the method to produce metal–carbon composites, Pt1−xNix/CNF, with an adjustable Pt/Ni ratio. The composites represent Pt1−xNix (x = 0.0–1.0) nanoparticles embedded within a structure of carbon nanofibers (CNF). The synthesis of the composites is based on a spontaneous disintegration of Pt1−xNix alloys in an ethylene-containing atmosphere with the formation of CNF. The initial Pt1−xNix alloys were prepared by thermolysis of multicomponent precursors. They possess a porous structure formed by fragments of 100–200 nm. As was shown by X-ray diffraction analysis, the crystal structure of the alloys containing 0–30 and 60–100 at.% Ni corresponds to a fcc lattice based on platinum (Fm-3m), while the Pt0.50Ni0.50 sample is an intermetallic compound with the tetragonal structure (P4/mmm). The impact of the Ni content in the Pt1−xNix samples on their activity in ethylene decomposition was studied as well. As was revealed, the efficiency of Pt1−xNix alloys in this process increases with the rise of Ni concentration. The composite samples were examined in an electrochemical hydrogen evolution reaction. The synthesized Pt1-xNix/CNF composites demonstrated superior activity if compared with the Pt/Vulcan commercial catalyst.
- Open Access
Precise Characterization of CNF-Coated Microfibers Using Transmission Electron Microscopy
The synthesis and characterization of fibrous materials with a hierarchical structure are of great importance for materials sciences. Among this class of materials, microfibers of different natures coated with carbon nanofibers attract special interest. Such coating modifies the surface of microfibers, makes it rougher, and thus strengthens its interaction with matrices being reinforced by the addition of these microfibers. In the present work, a series of hierarchical materials based on carbon microfibers, basalt microfibers, and fiberglass cloth coated with up to 50 wt% of carbon nanofibers was synthesized via the catalytic chemical vapor deposition technique. The initial items were impregnated with an aqueous solution of nickel nitrate and reduced in a hydrogen flow. Then, the catalytic chemical vapor deposition process using C2H4 or C2H4Cl2 as a carbon source was carried out. A simple and cost-effective technique for the preparation of the samples of hierarchical materials for transmission electron microscopy examination was developed and applied for the first time. The proposed method of sample preparation for sequential TEM visualization implies an ultrasonic treatment of up to four samples simultaneously under the same conditions by using a special sample holder. As was found, the relative strength of carbon nanofibers coating the surface of microfibers decreases in the order of CNF/CMF > CNF/BMF > CNF/FGC. Two effects of the ultrasonic action on the carbon coating were revealed. First, strongly bonded carbon nanofibers undergo significant breakage. Such behavior is typical for carbon and basalt microfibers. Secondly, carbon nanofibers can be completely detached from the microfiber surface, as was observed in the case of fiberglass cloth. In the case of CNF/CMF material, the graphitized surface of carbon microfiber is coherent with the structure of carbon nanofiber fragments grown on it, which explains the highest adhesion strength of the carbon nanolayer coated on carbon microfibers.
Open AccessPrecise Characterization of CNF-Coated Microfibers Using Transmission Electron Microscopy
The synthesis and characterization of fibrous materials with a hierarchical structure are of great importance for materials sciences. Among this class of materials, microfibers of different natures coated with carbon nanofibers attract special interest. Such coating modifies the surface of microfibers, makes it rougher, and thus strengthens its interaction with matrices being reinforced by the addition of these microfibers. In the present work, a series of hierarchical materials based on carbon microfibers, basalt microfibers, and fiberglass cloth coated with up to 50 wt% of carbon nanofibers was synthesized via the catalytic chemical vapor deposition technique. The initial items were impregnated with an aqueous solution of nickel nitrate and reduced in a hydrogen flow. Then, the catalytic chemical vapor deposition process using C2H4 or C2H4Cl2 as a carbon source was carried out. A simple and cost-effective technique for the preparation of the samples of hierarchical materials for transmission electron microscopy examination was developed and applied for the first time. The proposed method of sample preparation for sequential TEM visualization implies an ultrasonic treatment of up to four samples simultaneously under the same conditions by using a special sample holder. As was found, the relative strength of carbon nanofibers coating the surface of microfibers decreases in the order of CNF/CMF > CNF/BMF > CNF/FGC. Two effects of the ultrasonic action on the carbon coating were revealed. First, strongly bonded carbon nanofibers undergo significant breakage. Such behavior is typical for carbon and basalt microfibers. Secondly, carbon nanofibers can be completely detached from the microfiber surface, as was observed in the case of fiberglass cloth. In the case of CNF/CMF material, the graphitized surface of carbon microfiber is coherent with the structure of carbon nanofiber fragments grown on it, which explains the highest adhesion strength of the carbon nanolayer coated on carbon microfibers.
- Open Access
Comparative Study on Carbon Erosion of Nickel Alloys in the Presence of Organic Compounds under Various Reaction Conditions
The processes of carbon erosion of nickel alloys during the catalytic pyrolysis of organic compounds with the formation of carbon nanofibers in a flow-through reactor as well as under reaction conditions in a close volume (Reactions under Autogenic Pressure at Elevated Temperature, RAPET) were studied. The efficiency of the ferromagnetic resonance method to monitor the appearance of catalytically active nickel particles in these processes has been shown. As found, the interaction of bulk Ni-Cr alloy with the reaction medium containing halogenated hydrocarbons (1,2-dichloroethane, 1-iodobutane, 1-bromobutane) results in the appearance of ferromagnetic particles of similar dimensions (~200–300 nm). In the cases of hexachlorobenzene and hexafluorobenzene, the presence of a hydrogen source (hexamethylbenzene) in the reaction mixture was shown to be highly required. The microdispersed samples of Ni-Cu and Ni-Mo alloys were prepared by mechanochemical alloying of powders and by reductive thermolysis of salts-precursors, accordingly. Their interaction with polymers (polyethylene and polyvinyl chloride) under RAPET conditions and with ethylene and 1,2-dichloroethane in a flow-through reactor are comparatively studied as well. According to microscopic data, the morphology of the formed carbon nanofibers is affected by the alloy composition and by the nature of the used organic substrate.
Open AccessComparative Study on Carbon Erosion of Nickel Alloys in the Presence of Organic Compounds under Various Reaction Conditions
The processes of carbon erosion of nickel alloys during the catalytic pyrolysis of organic compounds with the formation of carbon nanofibers in a flow-through reactor as well as under reaction conditions in a close volume (Reactions under Autogenic Pressure at Elevated Temperature, RAPET) were studied. The efficiency of the ferromagnetic resonance method to monitor the appearance of catalytically active nickel particles in these processes has been shown. As found, the interaction of bulk Ni-Cr alloy with the reaction medium containing halogenated hydrocarbons (1,2-dichloroethane, 1-iodobutane, 1-bromobutane) results in the appearance of ferromagnetic particles of similar dimensions (~200–300 nm). In the cases of hexachlorobenzene and hexafluorobenzene, the presence of a hydrogen source (hexamethylbenzene) in the reaction mixture was shown to be highly required. The microdispersed samples of Ni-Cu and Ni-Mo alloys were prepared by mechanochemical alloying of powders and by reductive thermolysis of salts-precursors, accordingly. Their interaction with polymers (polyethylene and polyvinyl chloride) under RAPET conditions and with ethylene and 1,2-dichloroethane in a flow-through reactor are comparatively studied as well. According to microscopic data, the morphology of the formed carbon nanofibers is affected by the alloy composition and by the nature of the used organic substrate.