Yasin Mehdizadeh Chellehbari
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Yasin Mehdizadeh Chellehbari has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Samaneh Shahgaldi
Hydrogen Research Institute, University of Quebec Trois Rivieres (UQTR), Trois Rivieres, Quebec G8Z 4M3, Canada
7 shared publications - Abhay Gupta
Hydrogen Research Institute, University of Quebec at Trois Rivieres
4 shared publications Leila Moradizadeh
4 shared publicationsMohammadhossein Johar
3 shared publications- Xianguo Li
University of Waterloo
3 shared publications Abhay Gupta
2 shared publications
Latest Publications
- Open Access
- 15 October 2025
- Published by Elsevier in eTransportation
- Vol. 26
Machine learning-assisted optimization of NbTa alloy coating thickness via DC magnetron sputtering for SS316L bipolar plates in PEMFCs
- 15 October 2025
- Published by Elsevier in eTransportation
- Vol. 26
Open AccessMachine learning-assisted optimization of NbTa alloy coating thickness via DC magnetron sputtering for SS316L bipolar plates in PEMFCs
- Open Access
- 15 May 2025
- Published by Elsevier in Journal of Power Sources
- Vol. 647
Optimized tantalum interlayer thickness for PTLs: Enhancing PEMWE performance, stability, and reducing precious metal loading
- 15 May 2025
- Published by Elsevier in Journal of Power Sources
- Vol. 647
Open AccessOptimized tantalum interlayer thickness for PTLs: Enhancing PEMWE performance, stability, and reducing precious metal loading
- Open Access
- 12 May 2025
- Published by Elsevier in Materials Today Energy
- Vol. 51
Evaluation of niobium-based bipolar plates with ultra-low precious metal coatings for high-performance and durable PEM water electrolyzers
- 12 May 2025
- Published by Elsevier in Materials Today Energy
- Vol. 51
Open AccessEvaluation of niobium-based bipolar plates with ultra-low precious metal coatings for high-performance and durable PEM water electrolyzers
- Open Access
- 21 December 2024
- Published by Elsevier in Journal of Power Sources
- Vol. 630
Achieving high performance and durability with ultra-low precious metal nanolayer on porous transport layer for PEMWE application
- 21 December 2024
- Published by Elsevier in Journal of Power Sources
- Vol. 630
Open AccessAchieving high performance and durability with ultra-low precious metal nanolayer on porous transport layer for PEMWE application
- Open Access
- 16 November 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 94, 1114-1129
Porous transport layers with low Pt loading having Nb–Ta alloy as interlayer for proton exchange membrane water electrolyzers
- 16 November 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 94, 1114-1129
Open AccessPorous transport layers with low Pt loading having Nb–Ta alloy as interlayer for proton exchange membrane water electrolyzers
- Top Cited PapersOpen Access
- 23 September 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 88, 726-747
A comprehensive review of the material innovations and corrosion mitigation strategies for PEMWE bipolar plates
- 23 September 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 88, 726-747
Top Cited PapersOpen AccessA comprehensive review of the material innovations and corrosion mitigation strategies for PEMWE bipolar plates
- Open Access
Impact of Surface Pretreatment on the Corrosion Resistance and Adhesion of Thin Film Coating on SS316L Bipolar Plates for Proton-Exchange Membrane Fuel Cell Applications
Coated SS316L is a potential alternative to the graphite bipolar plates (BPPs) used in proton-exchange membrane fuel cells (PEMFCs) owing to their low manufacturing cost and machinability. Due to their susceptibility to corrosion and passivation, which increases PEMFC ohmic resistance, protective and conductive coatings on SS316L have been developed. However, coating adhesion is one of the challenges in the harsh acidic environment of PEMFCs, affecting the performance and durability of BPPs. This study compares mechanical polishing and the frequently adopted chemical etchants for SS316L: Adler’s, V2A, and Carpenter’s etchant with different etching durations and their impact on the wettability, adhesion, and corrosion resistance of a Nb-coated SS316L substrate. Contact angle measurements and laser microscopy revealed that all etching treatments increased the hydrophobicity and surface roughness of SS316L substrates. Ex situ potentiodynamic and potentiostatic polarization tests and interfacial contact resistance analysis revealed high corrosion resistance, interfacial conductivity, and adhesion of the Nb-coated SS316L substrate pretreated with V2A (7 min) and Adler’s (3 min) etchant. Increased hydrophobicity (contact angle = 101°) and surface roughness (Ra = 74 nm) achieved using V2A etchant led to the lowest corrosion rate (3.3 µA.cm−2) and interfacial resistance (15.4 mΩ.cm2). This study established pretreatment with V2A etchant (a solution of HNO3, HCl, and DI water (1:9:23 mole ratio)) as a promising approach for improving the longevity, electrochemical stability, and efficiency of the coated SS316L BPPs for PEMFC application.
Open AccessImpact of Surface Pretreatment on the Corrosion Resistance and Adhesion of Thin Film Coating on SS316L Bipolar Plates for Proton-Exchange Membrane Fuel Cell Applications
Coated SS316L is a potential alternative to the graphite bipolar plates (BPPs) used in proton-exchange membrane fuel cells (PEMFCs) owing to their low manufacturing cost and machinability. Due to their susceptibility to corrosion and passivation, which increases PEMFC ohmic resistance, protective and conductive coatings on SS316L have been developed. However, coating adhesion is one of the challenges in the harsh acidic environment of PEMFCs, affecting the performance and durability of BPPs. This study compares mechanical polishing and the frequently adopted chemical etchants for SS316L: Adler’s, V2A, and Carpenter’s etchant with different etching durations and their impact on the wettability, adhesion, and corrosion resistance of a Nb-coated SS316L substrate. Contact angle measurements and laser microscopy revealed that all etching treatments increased the hydrophobicity and surface roughness of SS316L substrates. Ex situ potentiodynamic and potentiostatic polarization tests and interfacial contact resistance analysis revealed high corrosion resistance, interfacial conductivity, and adhesion of the Nb-coated SS316L substrate pretreated with V2A (7 min) and Adler’s (3 min) etchant. Increased hydrophobicity (contact angle = 101°) and surface roughness (Ra = 74 nm) achieved using V2A etchant led to the lowest corrosion rate (3.3 µA.cm−2) and interfacial resistance (15.4 mΩ.cm2). This study established pretreatment with V2A etchant (a solution of HNO3, HCl, and DI water (1:9:23 mole ratio)) as a promising approach for improving the longevity, electrochemical stability, and efficiency of the coated SS316L BPPs for PEMFC application.
- Open Access
Mechanism Understanding of Li-ion Separation Using A Perovskite-Based Membrane
Lithium ions play a crucial role in the energy storage industry. Finding suitable lithium-ion-conductive membranes is one of the important issues of energy storage studies. Hence, a perovskite-based membrane, Lithium Lanthanum Titanate (LLTO), was innovatively implemented in the presence and absence of solvents to precisely understand the mechanism of lithium ion separation. The ion-selective membrane’s mechanism and the perovskite-based membrane’s efficiency were investigated using Molecular Dynamic (MD) simulation. The results specified that the change in the ambient condition, pH, and temperature led to a shift in LLTO pore sizes. Based on the results, pH plays an undeniable role in facilitating lithium ion transmission through the membrane. It is noticeable that the hydrogen bond interaction between the ions and membrane led to an expanding pore size, from (1.07 Å) to (1.18–1.20 Å), successfully enriching lithium from seawater. However, this value in the absence of the solvent would have been 1.1 Å at 50 °C. It was found that increasing the temperature slightly impacted lithium extraction. The charge analysis exhibited that the trapping energies applied by the membrane to the first three ions (Li+, K+, and Na+) were more than the ions’ hydration energies. Therefore, Li+, K+, and Na+ were fully dehydrated, whereas Mg2+ was partially dehydrated and could not pass through the membrane. Evaluating the membrane window diameter, and the combined effect of the three key parameters (barrier energy, hydration energy, and binding energy) illustrates that the required energy to transport Li ions through the membrane is higher than that for other monovalent cations.
Open AccessMechanism Understanding of Li-ion Separation Using A Perovskite-Based Membrane
Lithium ions play a crucial role in the energy storage industry. Finding suitable lithium-ion-conductive membranes is one of the important issues of energy storage studies. Hence, a perovskite-based membrane, Lithium Lanthanum Titanate (LLTO), was innovatively implemented in the presence and absence of solvents to precisely understand the mechanism of lithium ion separation. The ion-selective membrane’s mechanism and the perovskite-based membrane’s efficiency were investigated using Molecular Dynamic (MD) simulation. The results specified that the change in the ambient condition, pH, and temperature led to a shift in LLTO pore sizes. Based on the results, pH plays an undeniable role in facilitating lithium ion transmission through the membrane. It is noticeable that the hydrogen bond interaction between the ions and membrane led to an expanding pore size, from (1.07 Å) to (1.18–1.20 Å), successfully enriching lithium from seawater. However, this value in the absence of the solvent would have been 1.1 Å at 50 °C. It was found that increasing the temperature slightly impacted lithium extraction. The charge analysis exhibited that the trapping energies applied by the membrane to the first three ions (Li+, K+, and Na+) were more than the ions’ hydration energies. Therefore, Li+, K+, and Na+ were fully dehydrated, whereas Mg2+ was partially dehydrated and could not pass through the membrane. Evaluating the membrane window diameter, and the combined effect of the three key parameters (barrier energy, hydration energy, and binding energy) illustrates that the required energy to transport Li ions through the membrane is higher than that for other monovalent cations.