Yang Cai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yang Cai has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Shuai Zhang
Aalborg University
9 shared publications - Peng Mei
School of Optical and Electronic Information, Huazhong University of Science and Technology, Wuhan, China
7 shared publications - Xian Qi Lin
Yangtze Delta Region Institute (Huzhou), University of Electronic Science and Technology of China, Huzhou, China
5 shared publications - Gert Frolund Pedersen
Aalborg University
4 shared publications - Guangsheng Deng
Hefei University of Technology
2 shared publications - Peyman Aghabeyki
Department of Electronic Systems, Aalborg University, Aalborg, Denmark
2 shared publications
Latest Publications
- 24 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 74 (1) , 394-402
Analytical Synthesis of 2-D Flat-Top Beam and Its Application on 2-D Beam-Steerable Transmitarray Antenna in the 25-GHz Band
Two-dimensional (2D) flat-top beams are of great significance in wireless communication applications. This article presents the analytical synthesis of a 2D flat-top beam on a reflectarray (RA) antenna (i.e., a reflectarray + a feed source), and demonstrates its application in enabling a 2D beam-steerable transmitarray (TA) antenna in the 25 GHz band. A subordinate sequence, which contributes to the generation of a quasi-sawtooth-shaped beam, is first defined and then manipulated with two key parameters. By performing axially rotational phase symmetry operations on this sequence, quasi-sawtooth-shaped beams in all φ-cut planes are obtained, a 2D flat-top beam is therefore achieved at broadside by superimposing these quasi-sawtooth-shaped beams, with flexible beamwidth adjustment. Furthermore, its beam direction can be tilted by introducing an additional phase gradient. This tilted 2D flat-top beam can be utilized to enable a 2D beam-steerable TA antenna with a reduced profile, where an integrated phase-shifting and phase gradient (I-PSPG) surface is positioned above the RA antenna with a separation. By mechanically rotating the RA and I-PSPG surface with the feed source fixed, the beam of the developed TA antenna can be dynamically manipulated while keeping the polarizations of all beams the same. For demonstration, a RA antenna with a tilted 2D flat-top beam at 30° is implemented and then utilized to realize a 2D beam-steerable TA antenna, achieving a beam-scanning cone of 64° with approximately 1.9 dB gain roll-off. Prototypes of the developed RA and beam-steerable TA antennas are fabricated and characterized at 25 GHz, where the measured results align well with the simulated ones. The developed 2D beam-steerable TA antenna is attractive for low wind-load scenarios.
- 24 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 74 (1) , 394-402
Analytical Synthesis of 2-D Flat-Top Beam and Its Application on 2-D Beam-Steerable Transmitarray Antenna in the 25-GHz Band
Two-dimensional (2D) flat-top beams are of great significance in wireless communication applications. This article presents the analytical synthesis of a 2D flat-top beam on a reflectarray (RA) antenna (i.e., a reflectarray + a feed source), and demonstrates its application in enabling a 2D beam-steerable transmitarray (TA) antenna in the 25 GHz band. A subordinate sequence, which contributes to the generation of a quasi-sawtooth-shaped beam, is first defined and then manipulated with two key parameters. By performing axially rotational phase symmetry operations on this sequence, quasi-sawtooth-shaped beams in all φ-cut planes are obtained, a 2D flat-top beam is therefore achieved at broadside by superimposing these quasi-sawtooth-shaped beams, with flexible beamwidth adjustment. Furthermore, its beam direction can be tilted by introducing an additional phase gradient. This tilted 2D flat-top beam can be utilized to enable a 2D beam-steerable TA antenna with a reduced profile, where an integrated phase-shifting and phase gradient (I-PSPG) surface is positioned above the RA antenna with a separation. By mechanically rotating the RA and I-PSPG surface with the feed source fixed, the beam of the developed TA antenna can be dynamically manipulated while keeping the polarizations of all beams the same. For demonstration, a RA antenna with a tilted 2D flat-top beam at 30° is implemented and then utilized to realize a 2D beam-steerable TA antenna, achieving a beam-scanning cone of 64° with approximately 1.9 dB gain roll-off. Prototypes of the developed RA and beam-steerable TA antennas are fabricated and characterized at 25 GHz, where the measured results align well with the simulated ones. The developed 2D beam-steerable TA antenna is attractive for low wind-load scenarios.
- 18 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 73 (11) , 8972-8980
Design of Broadband Low-Profile Transmitarrays at Ka-Band With High-Permittivity 3-D-Printed Materials
Transmitarrays (TAs) are a cost-effective solution for millimeter-wave antenna applications. The widespread use of fully dielectric TAs (DTAs) emerges from the manufacturing simplicity brought by 3D printing. Previously reported DTAs employ readily available low-permittivity materials (εr < 3). However, this implementation implies thicker lenses (exceeding one free space wavelength, > λ0), affecting the DTA performance compared with thinner TA based on printed-circuit-board (PCB) technology. This work shows that, when properly crafted, 3D-printed high-permittivity dielectric (HPD) materials can solve this problem. The design challenge is to circumvent the free-space mismatch and narrowband responses usually associated with HPD materials. A commercially available HPD material compatible with 3D printing is used as an example to demonstrate the feasibility of this type of DTA. This study includes the in-house material characterization for the designed frequency (εr = 13.1 at 30 GHz). A HPD TA is benchmarked against a conventional PCB-based TA for evaluating the impact of HPD materials for the design of this type of TA. A HPD TA with a diameter of 14 λ0 (λ0 is the wavelength at 30 GHz in free space) and a height of 0.4 λ0 (excluding the feed horn) is fabricated with the low-cost 3D printing method of fuse deposition modeling (FDM). When illuminated by a standard horn, the HPD TA antenna provides a 27.4 dBi gain, elevation scanning up to 45 degrees (through the horizontal displacement of the feed horn) with a scan loss of 2 dB and a 1-dB gain bandwidth of 16.3%.
- 18 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 73 (11) , 8972-8980
Design of Broadband Low-Profile Transmitarrays at Ka-Band With High-Permittivity 3-D-Printed Materials
Transmitarrays (TAs) are a cost-effective solution for millimeter-wave antenna applications. The widespread use of fully dielectric TAs (DTAs) emerges from the manufacturing simplicity brought by 3D printing. Previously reported DTAs employ readily available low-permittivity materials (εr < 3). However, this implementation implies thicker lenses (exceeding one free space wavelength, > λ0), affecting the DTA performance compared with thinner TA based on printed-circuit-board (PCB) technology. This work shows that, when properly crafted, 3D-printed high-permittivity dielectric (HPD) materials can solve this problem. The design challenge is to circumvent the free-space mismatch and narrowband responses usually associated with HPD materials. A commercially available HPD material compatible with 3D printing is used as an example to demonstrate the feasibility of this type of DTA. This study includes the in-house material characterization for the designed frequency (εr = 13.1 at 30 GHz). A HPD TA is benchmarked against a conventional PCB-based TA for evaluating the impact of HPD materials for the design of this type of TA. A HPD TA with a diameter of 14 λ0 (λ0 is the wavelength at 30 GHz in free space) and a height of 0.4 λ0 (excluding the feed horn) is fabricated with the low-cost 3D printing method of fuse deposition modeling (FDM). When illuminated by a standard horn, the HPD TA antenna provides a 27.4 dBi gain, elevation scanning up to 45 degrees (through the horizontal displacement of the feed horn) with a scan loss of 2 dB and a 1-dB gain bandwidth of 16.3%.
- 23 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 73 (3) , 1894-1899
Beam-Scanning Reflectarray With Switchable Polarization Based on Liquid Crystal at Millimeter Wave
This study presents a design for a millimeter-wave reflectarray (RA) with simultaneous polarization and beam direction control. A dual-polarized Unit Cell (UC) based on Liquid Crystal (LC) material is proposed and an RA is designed accordingly. The unit cell comprises a back-plate reflector, a double slot-loaded ground plane, and two rectangular patches. The LC material is used between the patches and the common slot-loaded ground plane. By illuminating the UC with a slant polarization, the wave decomposes into two components, and by applying a proper voltage to each patch, the polarization, and beam direction can be manipulated. A 10×10 RA has been fabricated and measured. The horn feed illuminates the RA with a fixed linear polarization and 4 types of polarization are generated with a 70° and 100° scanning range in the E- and H-plane, respectively. The measured 3-dB gain bandwidth is 6% and the Axial Ratio (AR) bandwidth is 5 % with around 15% aperture efficiency.
- 23 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 73 (3) , 1894-1899
Beam-Scanning Reflectarray With Switchable Polarization Based on Liquid Crystal at Millimeter Wave
This study presents a design for a millimeter-wave reflectarray (RA) with simultaneous polarization and beam direction control. A dual-polarized Unit Cell (UC) based on Liquid Crystal (LC) material is proposed and an RA is designed accordingly. The unit cell comprises a back-plate reflector, a double slot-loaded ground plane, and two rectangular patches. The LC material is used between the patches and the common slot-loaded ground plane. By illuminating the UC with a slant polarization, the wave decomposes into two components, and by applying a proper voltage to each patch, the polarization, and beam direction can be manipulated. A 10×10 RA has been fabricated and measured. The horn feed illuminates the RA with a fixed linear polarization and 4 types of polarization are generated with a 70° and 100° scanning range in the E- and H-plane, respectively. The measured 3-dB gain bandwidth is 6% and the Axial Ratio (AR) bandwidth is 5 % with around 15% aperture efficiency.
- 13 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (10) , 7536-7545
Efficient Beam Manipulation With Phase Symmetry Operations on Transmitarrays for Flat-Top Beams
Beam manipulation is of paramount importance in wave engineering, enabling diverse beam shapes like pencil beams, flat-top beams, and isoflux beams to cater to various application missions. Among the beams, shaping flat-top and isoflux beams remains challenging with the traditional synthesis approaches that mainly rely on optimization algorithms. Here, we develop transmitarrays to efficiently generate flat-top and isoflux beams from the first principle of field superposition with negligible optimizations, by performing phase symmetry operations. The theoretical analysis not only facilitates the shaping of flat-top and isoflux beams but also exhibits controllable beamwidths. Two prototypes using four-layer double-ring unit cells are fabricated and measured from 27-29 GHz. Experimental validation confirms the efficacy of the phase symmetry operations in generating flat-top beams with adjustable beamwidths. The concept of phase symmetry operations can be extended to other vectorial or scalar components, offering potential applications for the manipulation of various waves such as acoustic waves, water surface waves, and beyond, thereby advancing related applications.
- 13 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (10) , 7536-7545
Efficient Beam Manipulation With Phase Symmetry Operations on Transmitarrays for Flat-Top Beams
Beam manipulation is of paramount importance in wave engineering, enabling diverse beam shapes like pencil beams, flat-top beams, and isoflux beams to cater to various application missions. Among the beams, shaping flat-top and isoflux beams remains challenging with the traditional synthesis approaches that mainly rely on optimization algorithms. Here, we develop transmitarrays to efficiently generate flat-top and isoflux beams from the first principle of field superposition with negligible optimizations, by performing phase symmetry operations. The theoretical analysis not only facilitates the shaping of flat-top and isoflux beams but also exhibits controllable beamwidths. Two prototypes using four-layer double-ring unit cells are fabricated and measured from 27-29 GHz. Experimental validation confirms the efficacy of the phase symmetry operations in generating flat-top beams with adjustable beamwidths. The concept of phase symmetry operations can be extended to other vectorial or scalar components, offering potential applications for the manipulation of various waves such as acoustic waves, water surface waves, and beyond, thereby advancing related applications.
- 31 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (9) , 7359-7364
Electronically Reconfigurable Filtering Reflectarray Antenna Using Polarization Conversion Elements With Controllable Conversion Zeros
This communication introduces an electronically reconfigurable filtering reflectarray antenna (RFRA) with good frequency selectivity and wide beam-scanning angle. The proposed reconfigurable element consists of a metal ring loading two PIN diodes at the ring openings, a patch with a complementary split ring, an E-shaped patch, a ground plate, and the DC biasing network for PIN diodes, which can not only convert the y-polarized incident wave into the x-polarized reflected wave, but also offer a 1-bit reflection phase. Furthermore, the proposed element can generate two controllable conversion zeros to permit high-selectivity filtering performance and adjustable bandwidth. A RFRA with 40 × 40 elements is analyzed in detail to demonstrate the filtering and beam-scanning capabilities, whose realized gain can reach 26.4 dBi at 29 GHz with an aperture efficiency (AE) of 15.7% and beam scanning angle can reach 60°. For lab-level verification, a 10 × 10 RFRA prototype has been fabricated and measured. The measurement and simulation results align well with each other, demonstrating that the proposed RFRA has good frequency selectivity and wide beam-scanning capabilities.
- 31 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (9) , 7359-7364
Electronically Reconfigurable Filtering Reflectarray Antenna Using Polarization Conversion Elements With Controllable Conversion Zeros
This communication introduces an electronically reconfigurable filtering reflectarray antenna (RFRA) with good frequency selectivity and wide beam-scanning angle. The proposed reconfigurable element consists of a metal ring loading two PIN diodes at the ring openings, a patch with a complementary split ring, an E-shaped patch, a ground plate, and the DC biasing network for PIN diodes, which can not only convert the y-polarized incident wave into the x-polarized reflected wave, but also offer a 1-bit reflection phase. Furthermore, the proposed element can generate two controllable conversion zeros to permit high-selectivity filtering performance and adjustable bandwidth. A RFRA with 40 × 40 elements is analyzed in detail to demonstrate the filtering and beam-scanning capabilities, whose realized gain can reach 26.4 dBi at 29 GHz with an aperture efficiency (AE) of 15.7% and beam scanning angle can reach 60°. For lab-level verification, a 10 × 10 RFRA prototype has been fabricated and measured. The measurement and simulation results align well with each other, demonstrating that the proposed RFRA has good frequency selectivity and wide beam-scanning capabilities.
- 20 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71 (1) , 121-125
A Generalized Method for Gain Bandwidth Enhancement of Transmitarray Antennas Considering Oblique Incidences
This paper introduces a generalized phase compensation method to enhance gain, 1-dB gain bandwidth of transmitarrays considering oblique incidences. This method is based on studying the transmission phase of each element in the holistic framework of a transmitarray, where all oblique incidences to each element are included. As a result, the actual transmission phase of every element at different spatial positions involving oblique incidence effects can be obtained, which is leveraged to improve the performance of transmitarrays. The proposed method is especially efficient for transmitarrays with discrete phase states. For proof of the concept, dielectric lenses with a 2-bit phase quantization are configured to demonstrate performance enhancement. The simulated results show that the gain enhancement of 1.67 dB, 3.41 dB, and 4.5 dB at 26 GHz can be achieved when the focal length-to-diameter ratio (F/D) is 0.37, 0.24, and 0.14, respectively, which are experimentally verified by the measured results.
- 20 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71 (1) , 121-125
A Generalized Method for Gain Bandwidth Enhancement of Transmitarray Antennas Considering Oblique Incidences
This paper introduces a generalized phase compensation method to enhance gain, 1-dB gain bandwidth of transmitarrays considering oblique incidences. This method is based on studying the transmission phase of each element in the holistic framework of a transmitarray, where all oblique incidences to each element are included. As a result, the actual transmission phase of every element at different spatial positions involving oblique incidence effects can be obtained, which is leveraged to improve the performance of transmitarrays. The proposed method is especially efficient for transmitarrays with discrete phase states. For proof of the concept, dielectric lenses with a 2-bit phase quantization are configured to demonstrate performance enhancement. The simulated results show that the gain enhancement of 1.67 dB, 3.41 dB, and 4.5 dB at 26 GHz can be achieved when the focal length-to-diameter ratio (F/D) is 0.37, 0.24, and 0.14, respectively, which are experimentally verified by the measured results.
- Open Access
Dual-Band Frequency Selective Surface with Different Polarization Selectivity for Wireless Communication Application
This article proposes a dual-band, frequency- and polarization-selective surface. Multiple resonant modes are introduced using the U-shaped resonator with a ground via to achieve dual-band responses and polarization selectivity. Two symmetrically grounded U-shaped resonators are coupled through electrically coupled apertures in a common ground, resulting in a passband with two transmission zeros per polarization. A general design flowchart and additional examples at the S, X, and K-bands are presented as well. A prototype at X-band is analyzed, fabricated, and measured, showing the passband center frequencies of 9.68 GHz and 10.73 GHz, factional bandwidths of 3.45% and 3.48%, and insertion losses of 0.9 dB and 1.1 dB, respectively. Due to the high selectivity, small frequency ratio, low profile, and stable performance under oblique incidence, the proposed designs have application potential in wireless communication systems.
Open AccessDual-Band Frequency Selective Surface with Different Polarization Selectivity for Wireless Communication Application
This article proposes a dual-band, frequency- and polarization-selective surface. Multiple resonant modes are introduced using the U-shaped resonator with a ground via to achieve dual-band responses and polarization selectivity. Two symmetrically grounded U-shaped resonators are coupled through electrically coupled apertures in a common ground, resulting in a passband with two transmission zeros per polarization. A general design flowchart and additional examples at the S, X, and K-bands are presented as well. A prototype at X-band is analyzed, fabricated, and measured, showing the passband center frequencies of 9.68 GHz and 10.73 GHz, factional bandwidths of 3.45% and 3.48%, and insertion losses of 0.9 dB and 1.1 dB, respectively. Due to the high selectivity, small frequency ratio, low profile, and stable performance under oblique incidence, the proposed designs have application potential in wireless communication systems.
- 3 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 71 (4) , 3282-3293
A Dual-Polarized Reconfigurable Reflectarray With a Thin Liquid Crystal Layer and 2-D Beam Scanning
A novel approach for dual-polarized Liquid Crystal (LC) unit cell design is introduced, allowing significant thickness reduction of a LC layer without compromising its loss and phase shift. For each unit cell, LC is used for a tunable superstrate between a cross patch above and a square patch below. The square and cross patches are coupled through two slots for each polarization. By changing the voltage applied to the square and cross patches, the LC in-between varies the resonant frequency and phase of the unit cell to realize 2D beam steering. 10×10 dual-polarized reflectarray (RA) with 30 μm (0.0028 λ) and 4 μm (3.73×10 -4 λ) thick LC layers are simulated in the 28 GHz band, where the aperture efficiencies (AE) are 25.3% and 22.5%, respectively. As a proof of concept, the dual-polarized RA with 30 μm thick LC is fabricated manually and measured at 28.5 GHz. A measurement technique is proposed to obtain the phase curves of the RA and reduce the effect of fabrication errors. With the imperfect manual fabrication, the RA still achieves the measured realized gain of 14.6 dBi corresponding to 12.5% AE. Besides, ±45° beam steering is demonstrated in the 2D plane for both polarizations.
- 3 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 71 (4) , 3282-3293
A Dual-Polarized Reconfigurable Reflectarray With a Thin Liquid Crystal Layer and 2-D Beam Scanning
A novel approach for dual-polarized Liquid Crystal (LC) unit cell design is introduced, allowing significant thickness reduction of a LC layer without compromising its loss and phase shift. For each unit cell, LC is used for a tunable superstrate between a cross patch above and a square patch below. The square and cross patches are coupled through two slots for each polarization. By changing the voltage applied to the square and cross patches, the LC in-between varies the resonant frequency and phase of the unit cell to realize 2D beam steering. 10×10 dual-polarized reflectarray (RA) with 30 μm (0.0028 λ) and 4 μm (3.73×10 -4 λ) thick LC layers are simulated in the 28 GHz band, where the aperture efficiencies (AE) are 25.3% and 22.5%, respectively. As a proof of concept, the dual-polarized RA with 30 μm thick LC is fabricated manually and measured at 28.5 GHz. A measurement technique is proposed to obtain the phase curves of the RA and reduce the effect of fabrication errors. With the imperfect manual fabrication, the RA still achieves the measured realized gain of 14.6 dBi corresponding to 12.5% AE. Besides, ±45° beam steering is demonstrated in the 2D plane for both polarizations.
- 30 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 64 (5) , 1552-1559
A Monopole-Based Wideband Absorber for Ultralarge Angles
This article develops a broadband absorber by fully using the radiation features of monopole antennas for ultrawide-angle absorption application. A unit cell (UC) based on monopole antennas is proposed, and its working polarization is analyzed with the antenna reciprocity method and image theory. A wide-angle impedance matching layer is also introduced to further enhance the absorption at large angles. The optimized monopole-based UC reveals 90% absorptivity from 5.5–14.76 GHz at the incident angle of 80°. To the best of our knowledge, this is the first time to report an absorber that can work perfectly under such ultrawide angles in a broadband manner. An 11 × 36 array is configured and simulated to verify the effectiveness of the monopole-based UC. The monostatic and bistatic scattering are both reduced significantly as well as other diffuse scattering directions from the simulated results. A prototype of 110 mm × 360 mm is fabricated and measured. Time gating methods are adopted to diminish the direct coupling effect. The measurements are in good agreement with the full-wave simulation results.
- 30 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 64 (5) , 1552-1559
A Monopole-Based Wideband Absorber for Ultralarge Angles
This article develops a broadband absorber by fully using the radiation features of monopole antennas for ultrawide-angle absorption application. A unit cell (UC) based on monopole antennas is proposed, and its working polarization is analyzed with the antenna reciprocity method and image theory. A wide-angle impedance matching layer is also introduced to further enhance the absorption at large angles. The optimized monopole-based UC reveals 90% absorptivity from 5.5–14.76 GHz at the incident angle of 80°. To the best of our knowledge, this is the first time to report an absorber that can work perfectly under such ultrawide angles in a broadband manner. An 11 × 36 array is configured and simulated to verify the effectiveness of the monopole-based UC. The monostatic and bistatic scattering are both reduced significantly as well as other diffuse scattering directions from the simulated results. A prototype of 110 mm × 360 mm is fabricated and measured. Time gating methods are adopted to diminish the direct coupling effect. The measurements are in good agreement with the full-wave simulation results.
- Open Access
- 4 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 70 (10) , 8718-8728
On the Study of Reconfigurable Intelligent Surfaces in the Near-Field Region
As a reconfigurable intelligent surface (RIS) is expected to be implemented with a large aperture in terms of wavelengths, using a RIS to perform near-field rather than conventional far-field communications might gain some benefits. The electric fields in the near-field region from the near-field focusing and conventional far-field RISs are simulated and compared to assess and validate the benefits. Two metrics of benefit distance and near-field gain are defined to characterize the electric fields in the near-field region. The cumulative distribution function (CDF) related to the near-field gain is calculated to describe the benefits in the area of interest where the total scan patterns from the near-field focusing and conventional far-field RISs are plotted. For demonstration, the benefit distance, near-field gain, and CDFs are presented and calculated for near-field focusing RISs with assigned focal distances of 80 and 300mm. It is concluded that the benefit distance is a critical factor affecting the CDF directly. The effects of the size of a RIS and phase quantization of elements on the benefit distance, near-field gain, and CDF are also discussed. Moreover, the maximum focal distance of a near-field focusing RIS with a certain size is derived and specified. Finally, the electric fields of three prototypes (e.g., conventional far-field RIS, near-field focusing RISs with assigned focal distances of 500 and 1500mm.) at 26GHz are measured and compared, where the benefit distances and near-field gains are experimentally observed.
- 4 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 70 (10) , 8718-8728
Open AccessOn the Study of Reconfigurable Intelligent Surfaces in the Near-Field Region
As a reconfigurable intelligent surface (RIS) is expected to be implemented with a large aperture in terms of wavelengths, using a RIS to perform near-field rather than conventional far-field communications might gain some benefits. The electric fields in the near-field region from the near-field focusing and conventional far-field RISs are simulated and compared to assess and validate the benefits. Two metrics of benefit distance and near-field gain are defined to characterize the electric fields in the near-field region. The cumulative distribution function (CDF) related to the near-field gain is calculated to describe the benefits in the area of interest where the total scan patterns from the near-field focusing and conventional far-field RISs are plotted. For demonstration, the benefit distance, near-field gain, and CDFs are presented and calculated for near-field focusing RISs with assigned focal distances of 80 and 300mm. It is concluded that the benefit distance is a critical factor affecting the CDF directly. The effects of the size of a RIS and phase quantization of elements on the benefit distance, near-field gain, and CDF are also discussed. Moreover, the maximum focal distance of a near-field focusing RIS with a certain size is derived and specified. Finally, the electric fields of three prototypes (e.g., conventional far-field RIS, near-field focusing RISs with assigned focal distances of 500 and 1500mm.) at 26GHz are measured and compared, where the benefit distances and near-field gains are experimentally observed.