Qingguo Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Qingguo Wang has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
Jun Xu
MOE Key Laboratory of Advanced Micro-Structured Materials, School of Physics Science and Engineering, Institute for Advanced Study, Tongji University, Shanghai 200092, China
6 shared publicationsXiaodong Xu
Jiangsu Key Laboratory of Advanced Laser Materials and Devices, School of Physics and Electronic Engineering, Jiangsu Normal University, Xuzhou 221116, China
5 shared publicationsWudi Wang
MOE Key Laboratory of Advanced Micro-Structured Materials, School of Physics Science and Engineering, Institute for Advanced Study, Tongji University, Shanghai 200092, China
4 shared publicationsHuili Tang
MOE Key Laboratory of Advanced Micro-Structured Materials, School of Physics Science and Engineering, Institute for Advanced Study, Tongji University, Shanghai 200092, China
3 shared publicationsXiao Cao
Tongji Univ, Sch Phys Sci & Engn, Inst Adv Study, MOE Key Lab Adv Microstruct Mat, Shanghai 200092, Peoples R China
3 shared publications- Yanyan Xue
School of Physics Science and Engineering, Institute for Advanced Study, Tongji University, Shanghai 200092, China
3 shared publications
Latest Publications
- Open Access
- 1 January 2025
- Published by Shanghai Institute of Optics and Fine Mechanics in Chinese Optics Letters
- Vol. 23 (7) , 071403
Spectroscopic characterization and efficient tunable lasers of Ho:BaF2 single crystals
A high-quality 1% (atom fraction) Ho3+:BaF2 crystal was successfully grown using the temperature gradient technique (TGT). The optical properties of the crystal were investigated, and continuous-wave (CW) laser operation of Ho3+ ions in the 2 µm range was successfully demonstrated for the first time in the BaF2 crystal, to the best of our knowledge. Spectral parameters such as Ωt (t = 2, 4, 6) and radiative lifetimes were calculated and studied by the Judd–Ofelt (J–O) theory. The quality factor was calculated to be Q = 6.60 × 10-20 cm2·ms, and the full width at half-maximum (FWHM) was fitted to be 134.5 nm, indicating that the Ho:BaF2 crystal has a low laser threshold and broadband tunability. A maximum output power of 1.5 W and a slope efficiency of 29.3% were achieved by the 1908 nm fiber laser as the pumping source, with a relatively low threshold of 399 mW. Additionally, the Ho:BaF2 crystal achieved a tunable laser output with a bandwidth of 166.4 nm, which is the widest as reported for other 2 µm band Ho-doped fluoride crystals to the best of our knowledge. These results suggest that the Ho:BaF2 crystal has the potential to achieve femtosecond ultrafast pulse laser output through mode-locking operation.
- 1 January 2025
- Published by Shanghai Institute of Optics and Fine Mechanics in Chinese Optics Letters
- Vol. 23 (7) , 071403
Open AccessSpectroscopic characterization and efficient tunable lasers of Ho:BaF2 single crystals
A high-quality 1% (atom fraction) Ho3+:BaF2 crystal was successfully grown using the temperature gradient technique (TGT). The optical properties of the crystal were investigated, and continuous-wave (CW) laser operation of Ho3+ ions in the 2 µm range was successfully demonstrated for the first time in the BaF2 crystal, to the best of our knowledge. Spectral parameters such as Ωt (t = 2, 4, 6) and radiative lifetimes were calculated and studied by the Judd–Ofelt (J–O) theory. The quality factor was calculated to be Q = 6.60 × 10-20 cm2·ms, and the full width at half-maximum (FWHM) was fitted to be 134.5 nm, indicating that the Ho:BaF2 crystal has a low laser threshold and broadband tunability. A maximum output power of 1.5 W and a slope efficiency of 29.3% were achieved by the 1908 nm fiber laser as the pumping source, with a relatively low threshold of 399 mW. Additionally, the Ho:BaF2 crystal achieved a tunable laser output with a bandwidth of 166.4 nm, which is the widest as reported for other 2 µm band Ho-doped fluoride crystals to the best of our knowledge. These results suggest that the Ho:BaF2 crystal has the potential to achieve femtosecond ultrafast pulse laser output through mode-locking operation.
- 16 August 2024
- Published by Optica Publishing Group in Optics Express
- Vol. 32 (18) , 31644-31656
Component design and stable SESAM mode-locking of the disorder middle entropy Yb:CaSrBaF6 single crystal
To the best of our knowledge, this is the first report on continuous and passively mode-locked operation of the multi-component fluoride CaSrBaF6 crystal. A novel disorder laser material, Yb:CaSrBaF6 (Ca0.33Sr0.33Ba0.33F2) of multi-component middle entropy crystal was designed and grown by temperature gradient technique (TGT) for the first time. X-ray diffraction (XRD) and X-ray fluorescence (XRF) analysis of Yb:CaSrBaF6 crystal reveals that Ca2+, Sr2+, and Ba2+ of near equal atomic ratio (1:1:1) have formed a homogeneous single-phased fluorite solid solution. The first principle calculation further shows that Ca2+, Sr2+, Ba2+ ions tend to be evenly distributed in the matrix crystal. The total formation energy is the lowest -547.17 ev and the structure is also the most stable at this time. The spectral properties of the crystal are systematically characterized. The emission cross section of 2F5/2→2F7/2 transition at 1040 nm is 0.62 × 10−20 cm2 with the larger full width at half maximum (FWHM) of 60.5 nm. The evenly disordered distribution of various cations and lattice distortion effect leads to the more diverse local structure and the diversity of luminescence, which can cause non-uniform broadening of the spectrum. Meanwhile, the Yb:CaSrBaF6 crystal generated a continuous wave (CW) output power of 1.128 W, corresponding to a slope efficiency of 32% and an optical-to-optical conversion efficiency of 28.7% at 1055.4 nm. By implementing a semiconductor saturable absorber mirror (SESAM) for stable mode-locked laser operation, when the absorbed pump power reached 3.79 W, the laser ran into continuous wave mode-locking (CWML) regime, the maximum average output power of 123 mW was generated and the pulse duration of 89 ps was achieved at a pulse repetition rate of 54.6 MHz, with a pulse energy of 2.25 nJ and a pulse peak power of 25 W. Better laser performance could be expected after optimizing pump core diameter and elimination of dispersion. All results show that Yb:CaSrBaF6 crystal is regarded as a what we believe to be novel laser materials, which also provide a reference for the development of disordered material and other rare earth ions doping.
- 16 August 2024
- Published by Optica Publishing Group in Optics Express
- Vol. 32 (18) , 31644-31656
Component design and stable SESAM mode-locking of the disorder middle entropy Yb:CaSrBaF6 single crystal
To the best of our knowledge, this is the first report on continuous and passively mode-locked operation of the multi-component fluoride CaSrBaF6 crystal. A novel disorder laser material, Yb:CaSrBaF6 (Ca0.33Sr0.33Ba0.33F2) of multi-component middle entropy crystal was designed and grown by temperature gradient technique (TGT) for the first time. X-ray diffraction (XRD) and X-ray fluorescence (XRF) analysis of Yb:CaSrBaF6 crystal reveals that Ca2+, Sr2+, and Ba2+ of near equal atomic ratio (1:1:1) have formed a homogeneous single-phased fluorite solid solution. The first principle calculation further shows that Ca2+, Sr2+, Ba2+ ions tend to be evenly distributed in the matrix crystal. The total formation energy is the lowest -547.17 ev and the structure is also the most stable at this time. The spectral properties of the crystal are systematically characterized. The emission cross section of 2F5/2→2F7/2 transition at 1040 nm is 0.62 × 10−20 cm2 with the larger full width at half maximum (FWHM) of 60.5 nm. The evenly disordered distribution of various cations and lattice distortion effect leads to the more diverse local structure and the diversity of luminescence, which can cause non-uniform broadening of the spectrum. Meanwhile, the Yb:CaSrBaF6 crystal generated a continuous wave (CW) output power of 1.128 W, corresponding to a slope efficiency of 32% and an optical-to-optical conversion efficiency of 28.7% at 1055.4 nm. By implementing a semiconductor saturable absorber mirror (SESAM) for stable mode-locked laser operation, when the absorbed pump power reached 3.79 W, the laser ran into continuous wave mode-locking (CWML) regime, the maximum average output power of 123 mW was generated and the pulse duration of 89 ps was achieved at a pulse repetition rate of 54.6 MHz, with a pulse energy of 2.25 nJ and a pulse peak power of 25 W. Better laser performance could be expected after optimizing pump core diameter and elimination of dispersion. All results show that Yb:CaSrBaF6 crystal is regarded as a what we believe to be novel laser materials, which also provide a reference for the development of disordered material and other rare earth ions doping.
- 8 June 2024
- Published by Elsevier in Journal of Luminescence
- Vol. 275
Crystal growth and spectroscopic analysis of Ho,Pr:BaF2 crystal for 3 μm mid-infrared emission
- 8 June 2024
- Published by Elsevier in Journal of Luminescence
- Vol. 275
Crystal growth and spectroscopic analysis of Ho,Pr:BaF2 crystal for 3 μm mid-infrared emission
- 11 November 2022
- Published by Elsevier in Journal of Luminescence
- Vol. 254
Enhance and modulated near-infrared luminescence of Tm3+:CaF2 crystal by co-doping Y3+ ions
- 11 November 2022
- Published by Elsevier in Journal of Luminescence
- Vol. 254
Enhance and modulated near-infrared luminescence of Tm3+:CaF2 crystal by co-doping Y3+ ions
- 15 July 2021
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 11 (8) , 2539-2546
Crystal growth and spectroscopic analysis of Ho, Pr:Sc2O3 crystal for 2.9 μm mid-IR laser
Ho3+, Pr3+: Sc2O3 crystal was successfully grown by the TGT method. The spectroscopic properties of the crystal were analyzed. The absorption cross section of Ho, Pr: Sc2O3 at 636 nm was 1.58×10–20 cm2. J-O theory was applied to analyze the fluorescence properties of the grown crystal at 2.9 μm. The intensity parameters Ωt (t=2,4,6), radiative transition rates, branching ratios and radiative lifetime were calculated. Ho, Pr: Sc2O3 exhibited strong emission at 2110 nm and 2864 nm with a stimulated emission cross section of 2.4 × 10–21 cm2 and 4.2 × 10–21 cm2, respectively. The fluorescence lifetime of the Ho3+ 5I6 and 5I7 levels were measured to be 1.64 ms and 5.74 ms. These results show that the Ho, Pr: Sc2O3 crystal would be a potential laser material at the 2.9 μm region.
- 15 July 2021
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 11 (8) , 2539-2546
Crystal growth and spectroscopic analysis of Ho, Pr:Sc2O3 crystal for 2.9 μm mid-IR laser
Ho3+, Pr3+: Sc2O3 crystal was successfully grown by the TGT method. The spectroscopic properties of the crystal were analyzed. The absorption cross section of Ho, Pr: Sc2O3 at 636 nm was 1.58×10–20 cm2. J-O theory was applied to analyze the fluorescence properties of the grown crystal at 2.9 μm. The intensity parameters Ωt (t=2,4,6), radiative transition rates, branching ratios and radiative lifetime were calculated. Ho, Pr: Sc2O3 exhibited strong emission at 2110 nm and 2864 nm with a stimulated emission cross section of 2.4 × 10–21 cm2 and 4.2 × 10–21 cm2, respectively. The fluorescence lifetime of the Ho3+ 5I6 and 5I7 levels were measured to be 1.64 ms and 5.74 ms. These results show that the Ho, Pr: Sc2O3 crystal would be a potential laser material at the 2.9 μm region.
- 7 October 2020
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 10 (11) , 2730-2737
Spectroscopic and continuous-wave laser properties of Er:GdScO3 crystal at 2.7 µm
Er:GdScO3 crystal was grown by the edge-defined film-fed (EFG) method for the first time. The rocking curve showed that the as-grown crystal has a high crystalline quality. The peak absorption cross section at 980 nm is 0.38×10−20 cm2 with full width at half maximum (FWHM) of 19.5 nm and the peak emission cross section at 2720 nm is 0.93×10−20 cm2 with FWHM of 149.0 nm. The fluorescence lifetimes of 4I11/2 and 4I13/2 were fitted to be 2.24 ms and 4.57 ms, respectively. At inversion ratio P≥0.5, the positive local peak of gain cross-section at 2.7 µm was obtained. Continuous-wave laser operation of Er:GdScO3 crystal was demonstrated. The maximum output power of 863 mW was obtained with a slope efficiency of 11.25%. The results indicated that Er:GdScO3 crystal is a potential laser material for 2.7 µm laser.
- 7 October 2020
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 10 (11) , 2730-2737
Spectroscopic and continuous-wave laser properties of Er:GdScO3 crystal at 2.7 µm
Er:GdScO3 crystal was grown by the edge-defined film-fed (EFG) method for the first time. The rocking curve showed that the as-grown crystal has a high crystalline quality. The peak absorption cross section at 980 nm is 0.38×10−20 cm2 with full width at half maximum (FWHM) of 19.5 nm and the peak emission cross section at 2720 nm is 0.93×10−20 cm2 with FWHM of 149.0 nm. The fluorescence lifetimes of 4I11/2 and 4I13/2 were fitted to be 2.24 ms and 4.57 ms, respectively. At inversion ratio P≥0.5, the positive local peak of gain cross-section at 2.7 µm was obtained. Continuous-wave laser operation of Er:GdScO3 crystal was demonstrated. The maximum output power of 863 mW was obtained with a slope efficiency of 11.25%. The results indicated that Er:GdScO3 crystal is a potential laser material for 2.7 µm laser.