RYRuijiang Yu

Ruijiang Yu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ruijiang Yu has a total of 10 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A Study on the Influence of Process Parameters on the Workpiece Surface Quality in the Cutting of Hard and Brittle Materials with Trepanning Drill

    by Ruijiang Yu, Shujuan Li, Zhengkang Zou, Lie Liang, Jiawei Zhang

    Hard and brittle materials have excellent physical and mechanical properties and are widely used in the fields of microelectronics and optoelectronics. However, due to their high hardness and brittleness, the machining quality of a workpiece struggles to meet the requirements of practical applications. In order to improve the surface quality of deep-hole machining of hard and brittle materials, this article analyzes the formation mechanism of surface roughness and the exit-chipping width during the drilling machining of hard and brittle materials and establishes a mathematical prediction model for the surface roughness and the exit-chipping width of hard and brittle materials using a trepanning cutter. The experimental study on K9 optical glass machining shows that the surface roughness of the workpiece and the exit-chipping width increase with the increase in feed rate, and decrease with the increase in rotational speed. Through comparison and verification between theoretical and experimental values, the average errors of workpiece surface roughness and the exit-chipping width are 13.15% and 6.73%, respectively. This article analyzes the reasons for the errors. The results indicate that the theoretical model proposed in this article can be used to predict the surface roughness and the exit-chipping width of hard and brittle materials processed under the same conditions, providing a theoretical basis to optimize process parameters to improve the surface quality of the workpiece.


  • Open Access

    Molecular Dynamics Simulation of Single-Crystal 4H-SiC Nano Scratching with Different Scratching Directions of the Tool

    by Lie Liang, Shujuan Li, Peng Chai, Kehao Lan, Ruijiang Yu

    4H-SiC (silicon carbide) is widely used in semiconductor devices due to its superior characteristics. However, processing techniques such as cutting, grinding, and polishing generally have problems such as low processing efficiency, high cost, difficulties guaranteeing processing quality, and serious material waste. The in-depth research on the mechanical behavior, material removal, and damage mechanism of SiC single crystals at the micro/nano scale is the foundation for solving these problems. This paper establishes a molecular dynamics simulation model for 4H-SiC single-crystal nano scratches, using three different directions of a Berkovich indenter to scratch the surface of the workpiece, studying the surface morphology, scratching force, and material removal during the scratching process. The results indicate that scratching directions of the tool varies, and the surface morphology also varies. After the scratching depth exceeds 1.6 nm, complete dislocations with a Burges vector of 1/3 appear on the crystal subsurface, leading to the plastic removal of the material. During the process of material removal, a smaller tool rake angle removes a larger amount of material chips. By analyzing the damage layer of the workpiece, the difference in the damage layer is smaller when the scratching direction is different, but the damage layer generated by the smaller rake angle of the scratching tool is thinner. It shows that the scratching force and workpiece temperature are relatively small when the rake angle of the scratching tool is small. Therefore, when scratching 4H-SiC single crystals, choosing a tool with a smaller rake angle is more beneficial for the process.


  • Open Access

    Fixed-Diamond Abrasive Wire-Saw Cutting Force Modeling Based on Changes in Contact Arc Lengths

    by Lie Liang, Shujuan Li, Kehao Lan, Jiabin Wang, Ruijiang Yu

    Monocrystalline silicon is widely used in the semiconductor market, but its hard and brittle physical properties make processing difficult. Fixed-diamond abrasive wire-saw (FAW) cutting is currently the most commonly used cutting method for hard and brittle materials due to advantages such as narrow cutting seams, low pollution, low cutting force and simple cutting process. During the process of cutting a wafer, the contact between the part and the wire is curved, and the arc length changes during the cutting process. This paper establishes a model of contact arc length by analyzing the cutting system. At the same time, a model of the random distribution of abrasive particles is established to solve the cutting force during the cutting process, using iterative algorithms to calculate cutting forces and chip surface saw marks. The error between the experiment and simulation of the average cutting force in the stable stage is less than 6%, and the errors with respect to the central angle and curvature of the saw arc on the wafer surface are less than 5% between the experiment and simulation. The relationship between the bow angle, contact arc length and cutting parameters is studied using simulations. The results show that the variation trend of the bow angle and contact arc length is consistent, increasing with an increase in the part feed rate and decreasing with an increase in the wire velocity.


  • Open Access

    Mathematical Modeling and Experimental Study of Cutting Force for Cutting Hard and Brittle Materials in Fixed Abrasive Trepanning Drill

    by Ruijiang Yu, Shujuan Li, Zhengkang Zou, Lie Liang

    Hard and brittle materials have excellent physical and mechanical performance, which are widely applied in the fields of microelectronics and optoelectronics. However, deep-hole machining of hard and brittle materials is very difficult and inefficient due to the high hardness and brittleness of these materials. To improve the quality and efficiency of deep-hole machining of hard and brittle materials, according to the brittle crack fracture removal mechanism of hard and brittle materials and the cutting model of the trepanning cutter, an analytical cutting force prediction model of hard and brittle materials processed using a trepanning cutter is established. This experimental study of K9 optical glass machining shows that as the feeding rate increase, the cutting force increase, and as the spindle speed increase, the cutting force decrease. By comparing and verifying the theoretical and experimental values, the average errors of axial force and torque are 5.0% and 6.7%, respectively, and the maximum error is 14.9%. This paper analyzes the reasons for the errors. The results indicate that the cutting force theoretical model can be used to predict the axial force and torque of machining hard and brittle materials under the same conditions, which provides a theory for optimizing machining process parameters.


  • Open Access

    Experimental Study on the Influence of Wire-Saw Wear on Cutting Force and Silicon Wafer Surface

    by Lie Liang, Shujuan Li, Kehao Lan, Ruijiang Yu, Jiabin Wang, Wen Zhao

    Hard and brittle materials such as monocrystalline silicon still occupy an important position in the semiconductor industry, but hard and brittle materials are difficult to process because of their physical properties. Fixed-diamond abrasive wire-saw cutting is the most widely used method for slicing hard and brittle materials. The diamond abrasive particles on the wire saw wear to a certain extent, which affects the cutting force and wafer surface quality in the cutting process. In this experiment, keeping all the given parameters unchanged, a square silicon ingot is cut repeatedly with a consolidated diamond abrasive wire saw until the wire saw breaks. The experimental results show that the cutting force decreases with the increase in cutting times in the stable grinding stage. The wear of abrasive particles starts at the edges and corners, and the macro failure mode of the wire saw is fatigue fracture. The fluctuation of the wafer surface profile gradually decreases. The surface roughness of wafer is steady during the wear steady stage, and the large damage pits on the wafer surface are reduced in the whole process of cutting.


  • Open Access

    Research on Stiffness Identification Method for Complex Joints Based on Modal Correlation Analysis

    by Ruijiang Yu, Shujuan Li, Lie Liang, Feilong Liu, Kaixuan Wang

    The dynamic performance of mechanical systems is seriously affected by the stiffness of mechanical joints. The tool holder system of the deep hole machine tool was taken as the object; based on the modal correlation of experiment and finite element simulation, a simple and practical method was proposed to obtain the joint stiffness of the tool holder system under the structure form of the tool overhang of 200 mm. For the same tool holder system, the simulation and experimental analysis were carried out with different structural forms of tool overhang of 300 and 400 mm, which further verified the correctness and feasibility of the method for obtaining the joint stiffness, as well as provided a new idea and certain theoretical basis for extracting the joint stiffness of the tool holder system in deep hole machining.