Amin Mirzaei
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Amin Mirzaei has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
A. H. Darbandi
Faculty of Material & Manufacturing Technologies, Malek Ashtar University of Technology, Tehran, Iran
1 shared publicationA.H. Darbandi
Faculty of Material & Manufacturing Technologies, Malek Ashtar University of Technology, Tehran, Iran
1 shared publicationAmirhossein Darbandi
1 shared publicationM. H. Alaei
Faculty of Material & Manufacturing Technologies, Malek Ashtar University of Technology, Tehran, Iran
1 shared publicationM. Ramzaninezhad
Faculty of Material & Manufacturing Technologies, Malek Ashtar University of Technology, Tehran, Iran
1 shared publicationM. Rezvaninasab
Faculty of Material & Manufacturing Technologies, Malek Ashtar University of Technology, Tehran, Iran
1 shared publication
Latest Publications
- 22 August 2023
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 31 (25) , 7452-7468
Effect of cyclic hydrothermal accelerated ageing on the mechanical behavior of components in adhesively bonded aluminum/composite joints reinforced with z-pins
- 22 August 2023
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 31 (25) , 7452-7468
Effect of cyclic hydrothermal accelerated ageing on the mechanical behavior of components in adhesively bonded aluminum/composite joints reinforced with z-pins
- 29 October 2022
- Published by Elsevier in Thin-Walled Structures
- Vol. 182
Quasi-static cyclic loading assessment of GFRP single-lap adhesive joints reinforced with z-pins
- 29 October 2022
- Published by Elsevier in Thin-Walled Structures
- Vol. 182
Quasi-static cyclic loading assessment of GFRP single-lap adhesive joints reinforced with z-pins
- 20 November 2021
- Published by Springer Nature in Mechanics of Composite Materials
- Vol. 57 (5) , 687-698
Experimental Investigation of the Effect of Adhesive-Impregnated Pins on the Mechanical Behavior of Z-Pinned Lap Shear Joints
- 20 November 2021
- Published by Springer Nature in Mechanics of Composite Materials
- Vol. 57 (5) , 687-698
Experimental Investigation of the Effect of Adhesive-Impregnated Pins on the Mechanical Behavior of Z-Pinned Lap Shear Joints
- 10 October 2021
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 98 (16) , 2662-2688
Experimental and numerical assessment of the effect of transverse reinforcing of AL-GFRP single lap adhesive joint using Z-pins under tensile loading
In this study, the effect of z-pins on the strength of the single-lap adhesive joint of GFRP composite-aluminum has been investigated. The joint consists of Al 7075T6 and Glass/Epoxy composite as adherends. Araldite 2015 A/B has been used as the adhesive along with four, six and eight steel pins that reinforced the joints in the z-direction. The stress analysis of the joints was done experimentally using tensile testing and numerically by the cohesive zone model (CZM) for progressive damage in commercial finite element software ABAQUS with the objective of reproducing the experimental results and better understanding of the failure mechanisms. The numerical results show that the maximum shear and peel stresses occur at the interface of the adhesive-composite in the joint. Also, local deformation was observed around the z-pin holes, thereby reducing the joint rigidity. It is concluded that there is a maximum number of z-pins beyond which the strength of the joint starts to decrease. This optimum number includes six z-pins in which the ultimate load of the joint increases by 19.5%. Finally, the numerical analysis has shown to have good agreement with the experimental results, indicating a promising model that can be used for further investigations for these joints.
- 10 October 2021
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 98 (16) , 2662-2688
Experimental and numerical assessment of the effect of transverse reinforcing of AL-GFRP single lap adhesive joint using Z-pins under tensile loading
In this study, the effect of z-pins on the strength of the single-lap adhesive joint of GFRP composite-aluminum has been investigated. The joint consists of Al 7075T6 and Glass/Epoxy composite as adherends. Araldite 2015 A/B has been used as the adhesive along with four, six and eight steel pins that reinforced the joints in the z-direction. The stress analysis of the joints was done experimentally using tensile testing and numerically by the cohesive zone model (CZM) for progressive damage in commercial finite element software ABAQUS with the objective of reproducing the experimental results and better understanding of the failure mechanisms. The numerical results show that the maximum shear and peel stresses occur at the interface of the adhesive-composite in the joint. Also, local deformation was observed around the z-pin holes, thereby reducing the joint rigidity. It is concluded that there is a maximum number of z-pins beyond which the strength of the joint starts to decrease. This optimum number includes six z-pins in which the ultimate load of the joint increases by 19.5%. Finally, the numerical analysis has shown to have good agreement with the experimental results, indicating a promising model that can be used for further investigations for these joints.