Piotr Ziarkowski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Piotr Ziarkowski has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Damian Bańkowski
Department of Materials Science and Materials Technology, Faculty of Machatronics and Mechanical Engineering, Kielce University of Technology, al. 1000-lecia P.P. 7, 25-314 Kielce, Poland
1 shared publication - Jarosław GRZĘDA
Kielce University of Technology, Poland, EU
1 shared publication - Kamil Klamczyński
Department of Manufacturing Engineering and Metrology, Kielce University of Technology, al. Tysiaclecia Panstwa Polskiego 7, 25-314 Kielce, Poland
1 shared publication - Lukasz Nowakowski
Department of Manufacturing Engineering and Metrology, Kielce University of Technology, al. Tysiaclecia Panstwa Polskiego 7, 25-314 Kielce, Poland
1 shared publication - Michal Skrzyniarz
Department of Manufacturing Engineering and Metrology, Kielce University of Technology, al. Tysiaclecia Panstwa Polskiego 7, 25-314 Kielce, Poland
1 shared publication - Natalia Kowalska
Faculty of Mechatronics and Mechanical Engineering, Kielce University of Technology, Tysiąclecia Państwa Polskiego 7 Ave., 25-314 Kielce, Poland
1 shared publication
Latest Publications
- Open Access
Accuracy Analysis of Holes Drilled in Ductile Cast Iron with an HSS Helical Drill Bit
Controlling macro-geometrical errors in the dry drilling of ductile cast iron remains a critical challenge for sustainable and cost-efficient automotive component manufacturing. This paper investigates the influence of cutting speed (vc) and feed per revolution (fn) on the dimensional and shape accuracy of holes drilled in EN-GJS-500-7 ductile cast iron using an HSS DIN 338 helical drill (Ø 11.8 mm, Ceratizit) on an AVIA VMC800 CNC milling centre. A one-factor-at-a-time (OFAT) experimental design was applied: the feed effect was evaluated at vc = 10 m/min with fn ∈ {0.10, 0.15, 0.20} mm/rev, while the speed effect was evaluated at fn = 0.20 mm/rev with vc ∈ {10, 25, 30} m/min. Cutting forces, torques, and vibration accelerations were recorded using an HBM MSC 10 transducer and a PCB 356A01 tri-axial accelerometer. Hole geometry was assessed on a Zeiss Contura G2 coordinate-measuring machine (CMM), and surface texture was evaluated with a TOPO 01P contact profilometer. The expanded measurement uncertainty (k = 2) was estimated based on duplicate test specimens. All drilled holes fell within the IT12 dimensional tolerance (PN-EN 22768-1:1999 grade c), with diameter oversizes ranging from +0.26 mm to +0.46 mm relative to the nominal bore. Cutting speed was identified as the dominant factor affecting both diameter oversize and cylindricity, which increased by 60% (from 0.10 to 0.16 mm) as vc rose from 10 to 30 m/min. Vibration accelerations increased nonlinearly between vc = 25 and 30 m/min (by a factor of 2.5×), indicating an approach to a structural resonance condition. The lowest surface roughness (Ra = 6.6 µm) was obtained at vc = 25 m/min. These findings establish clear physical baselines for tool deflection limits, demonstrating that managing dynamic process stability is vital for optimising macro-geometrical accuracy in the dry machining of cast iron alloys.
Open AccessAccuracy Analysis of Holes Drilled in Ductile Cast Iron with an HSS Helical Drill Bit
Controlling macro-geometrical errors in the dry drilling of ductile cast iron remains a critical challenge for sustainable and cost-efficient automotive component manufacturing. This paper investigates the influence of cutting speed (vc) and feed per revolution (fn) on the dimensional and shape accuracy of holes drilled in EN-GJS-500-7 ductile cast iron using an HSS DIN 338 helical drill (Ø 11.8 mm, Ceratizit) on an AVIA VMC800 CNC milling centre. A one-factor-at-a-time (OFAT) experimental design was applied: the feed effect was evaluated at vc = 10 m/min with fn ∈ {0.10, 0.15, 0.20} mm/rev, while the speed effect was evaluated at fn = 0.20 mm/rev with vc ∈ {10, 25, 30} m/min. Cutting forces, torques, and vibration accelerations were recorded using an HBM MSC 10 transducer and a PCB 356A01 tri-axial accelerometer. Hole geometry was assessed on a Zeiss Contura G2 coordinate-measuring machine (CMM), and surface texture was evaluated with a TOPO 01P contact profilometer. The expanded measurement uncertainty (k = 2) was estimated based on duplicate test specimens. All drilled holes fell within the IT12 dimensional tolerance (PN-EN 22768-1:1999 grade c), with diameter oversizes ranging from +0.26 mm to +0.46 mm relative to the nominal bore. Cutting speed was identified as the dominant factor affecting both diameter oversize and cylindricity, which increased by 60% (from 0.10 to 0.16 mm) as vc rose from 10 to 30 m/min. Vibration accelerations increased nonlinearly between vc = 25 and 30 m/min (by a factor of 2.5×), indicating an approach to a structural resonance condition. The lowest surface roughness (Ra = 6.6 µm) was obtained at vc = 25 m/min. These findings establish clear physical baselines for tool deflection limits, demonstrating that managing dynamic process stability is vital for optimising macro-geometrical accuracy in the dry machining of cast iron alloys.