Kai Ning
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Kai Ning has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
Pengkang Xie
State Key Laboratory of Disaster Prevention & Reduction for Power Grid State Grid Hunan Electric Power Company Disaster Prevention and Reduction Center Changsha City China
4 shared publicationsZhiyao Fu
State Key Laboratory of Disaster Prevention & Reduction for Power Grid State Grid Hunan Electric Power Company Disaster Prevention and Reduction Center Changsha City China
4 shared publicationsZhenglong Jiang
State Key Laboratory of Disaster Prevention & Reduction for Power Grid State Grid Hunan Electric Power Company Disaster Prevention and Reduction Center Changsha City China
3 shared publicationsBowen Wang
State Key Laboratory of Disaster Prevention & Reduction for Power Grid State Grid Hunan Electric Power Company Disaster Prevention and Reduction Center Changsha City China
2 shared publicationsJianping Hu
2 shared publicationsJiazheng Lu
State Key Laboratory of Disaster Prevention & Reduction for Power Grid State Grid Hunan Electric Power Company Disaster Prevention and Reduction Center Changsha City China
2 shared publications
Latest Publications
- 2 April 2026
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 143 (22)
Abnormal Heating and String Breakage in 500 kV Composite Insulators: A Multi‐Scale Mechanistic Study of Material Aging
Abnormal heating and string breakage of composite insulators threaten 500 kV transmission reliability. Four in‐service 500 kV insulators were examined for multi‐scale approach combining macroscopic inspection and dissection, water‐diffusion tests, infrared and ultraviolet diagnostics, and microstructural and physicochemical analyses of silicone rubber sheds and epoxy core rods. Insulators show severe chalking, cracking and pore formation of sheds at the high‐voltage end, accompanied by leakage currents of about 400–1100 μA, exceeding those in the middle and low‐voltage ends and indicating progressive interfacial debonding and decay‐like damage of the core rod. Abnormal heating is primarily concentrated at the junction between the high‐voltage end fitting and sheds, and installing grading rings narrows the temperature difference from roughly 4°C–7°C to 2°C–3°C and reduces ultraviolet photon counts by about 60%–80%, demonstrating that improved electric‐field grading effectively suppresses coupled electrical, thermal and discharge stresses. Microstructural and chemical evidence links polydimethylsiloxane chain scission, aluminium hydroxide to aluminium oxide transformation in silicone rubber, and nitric‐acid‐induced degradation and hydrolysis of the epoxy matrix to increased dielectric loss. These results establish a field‐distortion‐driven evolution pathway from shed aging, interfacial moisture ingress, core‐rod degradation, abnormal heating and eventual string breakage, providing a mechanistic basis for optimizing grading‐ring design and condition‐based maintenance of composite insulators.
- 2 April 2026
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 143 (22)
Abnormal Heating and String Breakage in 500 kV Composite Insulators: A Multi‐Scale Mechanistic Study of Material Aging
Abnormal heating and string breakage of composite insulators threaten 500 kV transmission reliability. Four in‐service 500 kV insulators were examined for multi‐scale approach combining macroscopic inspection and dissection, water‐diffusion tests, infrared and ultraviolet diagnostics, and microstructural and physicochemical analyses of silicone rubber sheds and epoxy core rods. Insulators show severe chalking, cracking and pore formation of sheds at the high‐voltage end, accompanied by leakage currents of about 400–1100 μA, exceeding those in the middle and low‐voltage ends and indicating progressive interfacial debonding and decay‐like damage of the core rod. Abnormal heating is primarily concentrated at the junction between the high‐voltage end fitting and sheds, and installing grading rings narrows the temperature difference from roughly 4°C–7°C to 2°C–3°C and reduces ultraviolet photon counts by about 60%–80%, demonstrating that improved electric‐field grading effectively suppresses coupled electrical, thermal and discharge stresses. Microstructural and chemical evidence links polydimethylsiloxane chain scission, aluminium hydroxide to aluminium oxide transformation in silicone rubber, and nitric‐acid‐induced degradation and hydrolysis of the epoxy matrix to increased dielectric loss. These results establish a field‐distortion‐driven evolution pathway from shed aging, interfacial moisture ingress, core‐rod degradation, abnormal heating and eventual string breakage, providing a mechanistic basis for optimizing grading‐ring design and condition‐based maintenance of composite insulators.
- Open Access
- 10 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 159883-159893
A Multivariate Nonlinear Regression-Based Method for Calculating Lightning Ablation Mass of Metal Mesh in Wind Turbine Blades
Lightning strikes have posed a severe threat to the operational safety of wind turbines. As an additional lightning-protection measure, metal meshes have been deployed on a number of turbines. However, under high-amplitude lightning currents, the mesh undergoes erosion, potentially compromising its lightning-protection effectiveness. Currently, blade-mounted meshes directly follow aerospace mesh standards, and the relationship between structural parameters and erosion mass on curved blade geometries is seldom reported. Therefore, This paper develops a parametric grid structure-based lighting strike simulation model for wind turbine blade metal mesh. The model analyzes the influence weights of mesh thickness, wire width, and grid size on the ablation mass of the metal mesh. The validity of the simulation model was verified through A+C combined lightning current ablation tests. A multivariate nonlinear regression equation for the ablation mass of the metal mesh was established, providing a quantitative method to evaluate the lightning protection capability of metal meshes with different structural parameters. The results show that under a density of 800 g/m3, the test group’s metal mesh had an ablation mass of 800 mg after exposure to the combined waveform, while the calculated ablation mass using the regression equation was 748 mg, yielding an error of 6.5%. The proposed equation provides a method to quantify the lightning protection capability of metal meshes with varying grid structural parameters.
- 10 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 159883-159893
Open AccessA Multivariate Nonlinear Regression-Based Method for Calculating Lightning Ablation Mass of Metal Mesh in Wind Turbine Blades
Lightning strikes have posed a severe threat to the operational safety of wind turbines. As an additional lightning-protection measure, metal meshes have been deployed on a number of turbines. However, under high-amplitude lightning currents, the mesh undergoes erosion, potentially compromising its lightning-protection effectiveness. Currently, blade-mounted meshes directly follow aerospace mesh standards, and the relationship between structural parameters and erosion mass on curved blade geometries is seldom reported. Therefore, This paper develops a parametric grid structure-based lighting strike simulation model for wind turbine blade metal mesh. The model analyzes the influence weights of mesh thickness, wire width, and grid size on the ablation mass of the metal mesh. The validity of the simulation model was verified through A+C combined lightning current ablation tests. A multivariate nonlinear regression equation for the ablation mass of the metal mesh was established, providing a quantitative method to evaluate the lightning protection capability of metal meshes with different structural parameters. The results show that under a density of 800 g/m3, the test group’s metal mesh had an ablation mass of 800 mg after exposure to the combined waveform, while the calculated ablation mass using the regression equation was 748 mg, yielding an error of 6.5%. The proposed equation provides a method to quantify the lightning protection capability of metal meshes with varying grid structural parameters.
- 27 August 2025
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 142 (48)
Research on Ultraviolet Resistance Method of Composite Insulators Silicone Rubber Doped With Nano‐ TiO 2
Ultraviolet (UV) light is one of the critical factors causing damage to the silicone rubber shed of composite insulators. To effectively enhance the UV resistance of silicone rubber and extend the service life of composite insulators, this study incorporates rutile nano‐TiO 2 to fabricate UV‐resistant silicone rubber composites. Accelerated UV aging tests (4000 h) in a UV aging test chamber compared UV‐resistant and ordinary silicone rubber samples, with multidimensional characterizations—including microstructural analysis, hydrophobicity testing, mechanical testing, dielectric spectroscopy, and Fourier‐transform infrared spectroscopy (FTIR)—performed at 1000‐h intervals. The results demonstrate that rutile nano‐TiO 2 significantly enhances the UV resistance of silicone rubber: under identical aging conditions, the degradation of mechanical properties of the UV‐resistant silicone rubber is mitigated; for example, the decrease in tear resistance is reduced by 51%, while its hydrophobicity and dielectric characteristics remain more stable after 2000 h of accelerated aging. The Tanaka model reveals that rutile TiO 2 absorbs UV radiation through hole–electron pair generation and scatters UV radiation through its nanoscale particle size at the bounded layer interface with silicone rubber, and the protection region depends on the interfacial density. This research provides technical guidance for the design and development of UV‐resistant and long‐life composite insulators in power systems.
- 27 August 2025
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 142 (48)
Research on Ultraviolet Resistance Method of Composite Insulators Silicone Rubber Doped With Nano‐ TiO 2
Ultraviolet (UV) light is one of the critical factors causing damage to the silicone rubber shed of composite insulators. To effectively enhance the UV resistance of silicone rubber and extend the service life of composite insulators, this study incorporates rutile nano‐TiO 2 to fabricate UV‐resistant silicone rubber composites. Accelerated UV aging tests (4000 h) in a UV aging test chamber compared UV‐resistant and ordinary silicone rubber samples, with multidimensional characterizations—including microstructural analysis, hydrophobicity testing, mechanical testing, dielectric spectroscopy, and Fourier‐transform infrared spectroscopy (FTIR)—performed at 1000‐h intervals. The results demonstrate that rutile nano‐TiO 2 significantly enhances the UV resistance of silicone rubber: under identical aging conditions, the degradation of mechanical properties of the UV‐resistant silicone rubber is mitigated; for example, the decrease in tear resistance is reduced by 51%, while its hydrophobicity and dielectric characteristics remain more stable after 2000 h of accelerated aging. The Tanaka model reveals that rutile TiO 2 absorbs UV radiation through hole–electron pair generation and scatters UV radiation through its nanoscale particle size at the bounded layer interface with silicone rubber, and the protection region depends on the interfacial density. This research provides technical guidance for the design and development of UV‐resistant and long‐life composite insulators in power systems.
- 5 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 31 (3) , 1233-1241
Effects of High-Energy Electron Beam-Modified Fumed Silica on the Structure and Properties of Silicone Rubber Composites
This study investigates the effects of high-energy electron beam irradiation on fumed silica fillers and the subsequent impact on the properties of synthesized silicone rubber. A systematic examination of the physical and electrical properties of the modified fumed silica and silicone rubber materials is conducted, and the underlying mechanisms behind the irradiated fumed silica’s influence on the silicone rubber are analyzed using first principles calculations. The findings reveal that as the irradiation dose increases, more defect structures emerge, and the defect center transitions from a dimer configuration to a puckered configuration. First principles calculations confirm that this defect center alteration leads to reduced surface energy. Fumed silica containing a higher number of defect structures results in improved mechanical properties and decreased dielectric properties for the silicone rubber material. These outcomes primarily stem from the increased presence of oxygen vacancies in the irradiated fumed silica, which correlates with reduced surface energy and energy band gap in the first principles calculations. This research is essential for understanding the microscopic changes in fumed silica as a filler under irradiation and the mechanism of its effect on silicone rubber, ultimately providing guidance for enhancing the functionality of silicone rubber materials.
- 5 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 31 (3) , 1233-1241
Effects of High-Energy Electron Beam-Modified Fumed Silica on the Structure and Properties of Silicone Rubber Composites
This study investigates the effects of high-energy electron beam irradiation on fumed silica fillers and the subsequent impact on the properties of synthesized silicone rubber. A systematic examination of the physical and electrical properties of the modified fumed silica and silicone rubber materials is conducted, and the underlying mechanisms behind the irradiated fumed silica’s influence on the silicone rubber are analyzed using first principles calculations. The findings reveal that as the irradiation dose increases, more defect structures emerge, and the defect center transitions from a dimer configuration to a puckered configuration. First principles calculations confirm that this defect center alteration leads to reduced surface energy. Fumed silica containing a higher number of defect structures results in improved mechanical properties and decreased dielectric properties for the silicone rubber material. These outcomes primarily stem from the increased presence of oxygen vacancies in the irradiated fumed silica, which correlates with reduced surface energy and energy band gap in the first principles calculations. This research is essential for understanding the microscopic changes in fumed silica as a filler under irradiation and the mechanism of its effect on silicone rubber, ultimately providing guidance for enhancing the functionality of silicone rubber materials.
- Open Access
- 6 April 2023
- Published by Elsevier in Polymer Testing
- Vol. 122
Aging characteristics and lifespan prediction for composite insulator silicone rubber in a mountainous region environment
- 6 April 2023
- Published by Elsevier in Polymer Testing
- Vol. 122
Open AccessAging characteristics and lifespan prediction for composite insulator silicone rubber in a mountainous region environment
- 4 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 30 (1) , 31-40
Study on Silicone Rubber Composite Insulator Modified by High-Energy Electron Beam Irradiation
The impact of high-energy electron beam irradiation on silicone rubber composite insulator is investigated in this article. It was discovered that as the irradiation dose increased, the related properties of silicone rubber increased first and then decreased, with the static contact angle increasing to 111.8°, the tensile strength increasing to 4.59 MPa, the tear strength increasing to 26.8 kN/m, and the crosslinking density increasing to $7.09\times 10^{-{4}}$ mol/cm3, but the elongation decreasing. SEM observation revealed that silicone rubber was more compact after irradiation. attenuated total reflection-Fourier transform infrared spectroscopy (ATR-FTIR) and X-ray photoelectron spectroscopy (XPS) studies revealed that when the irradiation dose increased, the irradiation of silicone rubber shifted from crosslinking to degradation, and a new Si(−O)4 structure formed. Considering comprehensive performances, 40–50 kGy is the optimal irradiation dose. This article can provide support for understanding the irradiation modification of silicone rubber materials for composite insulator and also guide the preparation method of new silicone rubber.
- 4 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 30 (1) , 31-40
Study on Silicone Rubber Composite Insulator Modified by High-Energy Electron Beam Irradiation
The impact of high-energy electron beam irradiation on silicone rubber composite insulator is investigated in this article. It was discovered that as the irradiation dose increased, the related properties of silicone rubber increased first and then decreased, with the static contact angle increasing to 111.8°, the tensile strength increasing to 4.59 MPa, the tear strength increasing to 26.8 kN/m, and the crosslinking density increasing to $7.09\times 10^{-{4}}$ mol/cm3, but the elongation decreasing. SEM observation revealed that silicone rubber was more compact after irradiation. attenuated total reflection-Fourier transform infrared spectroscopy (ATR-FTIR) and X-ray photoelectron spectroscopy (XPS) studies revealed that when the irradiation dose increased, the irradiation of silicone rubber shifted from crosslinking to degradation, and a new Si(−O)4 structure formed. Considering comprehensive performances, 40–50 kGy is the optimal irradiation dose. This article can provide support for understanding the irradiation modification of silicone rubber materials for composite insulator and also guide the preparation method of new silicone rubber.