Sung Hoon Lee
Sung Hoon Lee has a total of 72 co-authors. Here are the top co-authors by number of shared publications:
Hyunbin Kim
Corning Technology Center Korea, Corning Precision Materials Co., Ltd., 212 Tangjeong-ro, Asan, Chungcheongnam-do 31454, Republic of Korea
7 shared publicationsHyunhang Park
Corning Technology Center Korea, Corning Precision Materials Co., Ltd., Asan, Republic of Korea
7 shared publicationsAravind R. Rammohan
Science and Technology Division, Corning Incorporated, One Science Center Drive, Corning, New York 14831, United States
6 shared publicationsSushmit Goyal
Science and Technology Division, Corning Incorporated, Corning, New York 14831, USA
6 shared publicationsKyoungmin Min
Platform Technology Lab, Samsung Advanced Institute of Technology, 130 Samsung-ro, Suwon, Gyeonggi-do 443-803, South Korea
5 shared publicationsEunseog Cho
Platform Technology Lab, Samsung Advanced Institute of Technology, 130 Samsung-ro, Suwon, Gyeonggi-do 443-803, South Korea
4 shared publications
Latest Publications
- 30 June 2026
- Published by Elsevier in Journal of Non-Crystalline Solids
- Vol. 690
Effects of divalent cation modifiers on ionic interdiffusion in aluminosilicate glasses
- 30 June 2026
- Published by Elsevier in Journal of Non-Crystalline Solids
- Vol. 690
Effects of divalent cation modifiers on ionic interdiffusion in aluminosilicate glasses
- 22 December 2025
- Published by AIP Publishing in The Journal of Chemical Physics
- Vol. 163 (24)
Titanium phosphate glasses: Beyond tetrahedral network structures
The structure of titanium phosphate glasses (TiO2)x(P2O5)1−x with 0.70 ≤ x ≤ 0.75 was investigated by combining neutron and high-energy x-ray diffraction with solid-state 31P nuclear magnetic resonance (NMR) and Raman spectroscopy. The results were interpreted with the aid of an analytical model that delivers the composition dependence of the structural motifs. The structure of these materials was also simulated using ab initio molecular dynamics. A detailed 31P magic-angle spinning (MAS) NMR lineshape analysis, aided by the results obtained from double-quantum coherence spectroscopy, indicates the presence of P–O–P-connected network forming units at a level decreasing from 23% to 11% with increasing x. The diffraction results show a Ti–O coordination number of 5.32(7) at x = 0.715 that increases to 5.49(7) at x = 0.750. The findings demonstrate the prevalence of five- and six-coordinated titanium atoms and the coexistence of both two-coordinated oxygen atoms, O(II), and three-coordinated oxygen atoms, O(III). The Ti-centered polyhedra contribute to a network in which the phosphate groups form P–O(II)–Ti and P–O(III)–2Ti connections, with signatures that are evident in the 31P MAS NMR spectra. The results suggest that structural variability is a key factor in promoting vitrification in this atypical glass-forming system. The findings provide a benchmark for investigating the structure of other glass-forming materials based on networks of higher-coordinated polyhedral units.
- 22 December 2025
- Published by AIP Publishing in The Journal of Chemical Physics
- Vol. 163 (24)
Titanium phosphate glasses: Beyond tetrahedral network structures
The structure of titanium phosphate glasses (TiO2)x(P2O5)1−x with 0.70 ≤ x ≤ 0.75 was investigated by combining neutron and high-energy x-ray diffraction with solid-state 31P nuclear magnetic resonance (NMR) and Raman spectroscopy. The results were interpreted with the aid of an analytical model that delivers the composition dependence of the structural motifs. The structure of these materials was also simulated using ab initio molecular dynamics. A detailed 31P magic-angle spinning (MAS) NMR lineshape analysis, aided by the results obtained from double-quantum coherence spectroscopy, indicates the presence of P–O–P-connected network forming units at a level decreasing from 23% to 11% with increasing x. The diffraction results show a Ti–O coordination number of 5.32(7) at x = 0.715 that increases to 5.49(7) at x = 0.750. The findings demonstrate the prevalence of five- and six-coordinated titanium atoms and the coexistence of both two-coordinated oxygen atoms, O(II), and three-coordinated oxygen atoms, O(III). The Ti-centered polyhedra contribute to a network in which the phosphate groups form P–O(II)–Ti and P–O(III)–2Ti connections, with signatures that are evident in the 31P MAS NMR spectra. The results suggest that structural variability is a key factor in promoting vitrification in this atypical glass-forming system. The findings provide a benchmark for investigating the structure of other glass-forming materials based on networks of higher-coordinated polyhedral units.
- 2 September 2022
- Published by Elsevier in Computational Materials Science
- Vol. 214
A high-throughput ab-initio study of diverse glasses: Accuracy of the atomic structure and refractive index
- 2 September 2022
- Published by Elsevier in Computational Materials Science
- Vol. 214
A high-throughput ab-initio study of diverse glasses: Accuracy of the atomic structure and refractive index
- Open Access
- 22 April 2022
- Published by MDPI AG in Biosensors
- Vol. 12 (5) , 266
Paper-Based Substrate for a Surface-Enhanced Raman Spectroscopy Biosensing Platform—A Silver/Chitosan Nanocomposite Approach
Paper is a popular platform material in all areas of sensor research due to its porosity, large surface area, and biodegradability, to name but a few. Many paper-based nanocomposites have been reported in the last decade as novel substrates for surface-enhanced Raman spectroscopy (SERS). However, there are still limiting factors, like the low density of hot spots or loss of wettability. Herein, we designed a process to fabricate a silver–chitosan nanocomposite layer on paper celluloses by a layer-by-layer method and pH-triggered chitosan assembly. Under microscopic observation, the resulting material showed a nanoporous structure, and silver nanoparticles were anchored evenly over the nanocomposite layer. In SERS measurement, the detection limit of 4-aminothiophenol was 5.13 ppb. Furthermore, its mechanical property and a strategy toward further biosensing approaches were investigated.
- 22 April 2022
- Published by MDPI AG in Biosensors
- Vol. 12 (5) , 266
Open AccessPaper-Based Substrate for a Surface-Enhanced Raman Spectroscopy Biosensing Platform—A Silver/Chitosan Nanocomposite Approach
Paper is a popular platform material in all areas of sensor research due to its porosity, large surface area, and biodegradability, to name but a few. Many paper-based nanocomposites have been reported in the last decade as novel substrates for surface-enhanced Raman spectroscopy (SERS). However, there are still limiting factors, like the low density of hot spots or loss of wettability. Herein, we designed a process to fabricate a silver–chitosan nanocomposite layer on paper celluloses by a layer-by-layer method and pH-triggered chitosan assembly. Under microscopic observation, the resulting material showed a nanoporous structure, and silver nanoparticles were anchored evenly over the nanocomposite layer. In SERS measurement, the detection limit of 4-aminothiophenol was 5.13 ppb. Furthermore, its mechanical property and a strategy toward further biosensing approaches were investigated.
- 21 October 2021
- Published by Springer Nature in Cellulose
- p. 1-13
Roles of paper composition and humidity on the adhesion between paper sheet and glass: a molecular dynamics study
- 21 October 2021
- Published by Springer Nature in Cellulose
- p. 1-13
Roles of paper composition and humidity on the adhesion between paper sheet and glass: a molecular dynamics study
- Open Access
Effect of Sputter Deposition on the Adhesion and Failure Behavior between Cu Film and Glassy Calcium Aluminosilicate: A Molecular Dynamics Study
Understanding the physical vapor deposition (PVD) process of metallic coatings on an inorganic substrate is essential for the packaging and semiconductor industry. In this work, we investigate a Copper (Cu) film deposition on a glassy Calcium Aluminosilicate (CAS) by PVD and its dependence on the incident energy. Molecular dynamics simulation is adopted to mimic the deposition process, and pure Cu film is grown on top of CAS surface forming intermixing region (IR) of Cu oxide. In the initial stage of deposition, incident Cu atoms are diffused into CAS bulk and aggregated at the surface which leads to the formation of IR. When the high incident energy, 2 eV, is applied, 20% more Cu atoms are observed at the interface compared to the low incident energy, 0.2 eV, due to enhanced lateral diffusion. As the Cu film grows, the amorphous thin Cu layer of 1 nm is temporarily formed on top of CAS, and crystallization with face-centered cubic from amorphous structure follows regardless of incident energy, and surface roughness is observed to be low for high incident energy cases. Deformation and failure behavior of Cu-CAS bilayer by pulling is investigated by steered molecular dynamics technique. The adhesive failure mode is observed, which implies the bilayer experiences a failure at the interface, and a 7% higher adhesion force is predicted for the high incident energy case. To find an origin of adhesion enhancement, the distribution of Cu atoms on the fractured CAS surface is analyzed, and it turns out that 6.3% more Cu atoms remain on the surface, which can be regarded as a source for the high adhesion force. Our findings hopefully give the insight to understand deposition and failure mechanisms between heterogeneous materials and are also helping to further improve Cu adhesion in sputter experiments.
Open AccessEffect of Sputter Deposition on the Adhesion and Failure Behavior between Cu Film and Glassy Calcium Aluminosilicate: A Molecular Dynamics Study
Understanding the physical vapor deposition (PVD) process of metallic coatings on an inorganic substrate is essential for the packaging and semiconductor industry. In this work, we investigate a Copper (Cu) film deposition on a glassy Calcium Aluminosilicate (CAS) by PVD and its dependence on the incident energy. Molecular dynamics simulation is adopted to mimic the deposition process, and pure Cu film is grown on top of CAS surface forming intermixing region (IR) of Cu oxide. In the initial stage of deposition, incident Cu atoms are diffused into CAS bulk and aggregated at the surface which leads to the formation of IR. When the high incident energy, 2 eV, is applied, 20% more Cu atoms are observed at the interface compared to the low incident energy, 0.2 eV, due to enhanced lateral diffusion. As the Cu film grows, the amorphous thin Cu layer of 1 nm is temporarily formed on top of CAS, and crystallization with face-centered cubic from amorphous structure follows regardless of incident energy, and surface roughness is observed to be low for high incident energy cases. Deformation and failure behavior of Cu-CAS bilayer by pulling is investigated by steered molecular dynamics technique. The adhesive failure mode is observed, which implies the bilayer experiences a failure at the interface, and a 7% higher adhesion force is predicted for the high incident energy case. To find an origin of adhesion enhancement, the distribution of Cu atoms on the fractured CAS surface is analyzed, and it turns out that 6.3% more Cu atoms remain on the surface, which can be regarded as a source for the high adhesion force. Our findings hopefully give the insight to understand deposition and failure mechanisms between heterogeneous materials and are also helping to further improve Cu adhesion in sputter experiments.
- Open Access
Review on Interfacial Bonding Mechanism of Functional Polymer Coating on Glass in Atomistic Modeling Perspective
Atomistic modeling methods are successfully applied to understand interfacial interaction in nanoscale size and analyze adhesion mechanism in the organic–inorganic interface. In this paper, we review recent representative atomistic simulation works, focusing on the interfacial bonding, adhesion strength, and failure behavior between polymer film and silicate glass. The simulation works are described under two categories, namely non-bonded and bonded interaction. In the works for non-bonded interaction, three main interactions, namely van der Waals interaction, polar interaction, and hydrogen bonds, are investigated, and the contributions to interfacial adhesion energy are analyzed. It is revealed that the most dominant interaction for adhesion is hydrogen bonding, but flexibility of the polymer film and modes of adhesion measurement test do affect adhesion and failure behavior. In the case of bonded interactions, the mechanism of covalent silane bond formation through condensation and hydrolysis process is reviewed, and surface reactivity, molecular density, and adhesion properties are calculated with an example of silane functionalized polymer. Besides interfacial interactions, effects of external conditions, such as surface morphology of the glass substrate and relative humidity on the adhesion and failure behavior, are presented, and modeling techniques developed for building interfacial system and calculating adhesion strengths are briefly introduced.
Open AccessReview on Interfacial Bonding Mechanism of Functional Polymer Coating on Glass in Atomistic Modeling Perspective
Atomistic modeling methods are successfully applied to understand interfacial interaction in nanoscale size and analyze adhesion mechanism in the organic–inorganic interface. In this paper, we review recent representative atomistic simulation works, focusing on the interfacial bonding, adhesion strength, and failure behavior between polymer film and silicate glass. The simulation works are described under two categories, namely non-bonded and bonded interaction. In the works for non-bonded interaction, three main interactions, namely van der Waals interaction, polar interaction, and hydrogen bonds, are investigated, and the contributions to interfacial adhesion energy are analyzed. It is revealed that the most dominant interaction for adhesion is hydrogen bonding, but flexibility of the polymer film and modes of adhesion measurement test do affect adhesion and failure behavior. In the case of bonded interactions, the mechanism of covalent silane bond formation through condensation and hydrolysis process is reviewed, and surface reactivity, molecular density, and adhesion properties are calculated with an example of silane functionalized polymer. Besides interfacial interactions, effects of external conditions, such as surface morphology of the glass substrate and relative humidity on the adhesion and failure behavior, are presented, and modeling techniques developed for building interfacial system and calculating adhesion strengths are briefly introduced.
- Open Access
- 12 February 2021
- Published by Springer Nature in Research Square
Roles of Paper Composition and Humidity on the Adhesion between Paper Sheet and Glass: A Molecular Dynamics Study
Understanding adhesion behavior between paper materials and inorganic substrate is important to minimize surface contamination by paper fragments. In this work, we investigate adhesion mechanisms between paper sheet and glass in terms of molecular interaction. Molecular dynamics simulations are employed to calculate adhesion force between paper sheet and the silica glass surfaces. Pulling and sliding tests are simulated to find the effects of the paper compositions such as mannan, glucan, and glucuronoxylan and humidity on the adhesion. Simulation results reveal that crystalline cellulose film of mannan unit (uni-directional hydroxyl groups) shows higher adhesion than that of glucan unit (bi-directional hydroxyl groups). Also, addition of just a few glucuronoxylan (xylan) hemicellulose molecules on the cellulose film remarkably enhances adhesion force, because of carboxylic acid groups with strong polarity in xylan. In addition, introduction of humidity leads to a further increase of adhesion due to hydrogen bonds bridged by water molecules. The adhesion force is maximized around 10 H2O/nm2 because as the humidity increases, hydrogen bond interactions are saturated, whereas the Van der Waals interactions decrease due to thicker water layer. It is discussed that consideration of the capillary force for paper may result in different adhesion response that reflects more realistic situation.
- 12 February 2021
- Published by Springer Nature in Research Square
Open AccessRoles of Paper Composition and Humidity on the Adhesion between Paper Sheet and Glass: A Molecular Dynamics Study
Understanding adhesion behavior between paper materials and inorganic substrate is important to minimize surface contamination by paper fragments. In this work, we investigate adhesion mechanisms between paper sheet and glass in terms of molecular interaction. Molecular dynamics simulations are employed to calculate adhesion force between paper sheet and the silica glass surfaces. Pulling and sliding tests are simulated to find the effects of the paper compositions such as mannan, glucan, and glucuronoxylan and humidity on the adhesion. Simulation results reveal that crystalline cellulose film of mannan unit (uni-directional hydroxyl groups) shows higher adhesion than that of glucan unit (bi-directional hydroxyl groups). Also, addition of just a few glucuronoxylan (xylan) hemicellulose molecules on the cellulose film remarkably enhances adhesion force, because of carboxylic acid groups with strong polarity in xylan. In addition, introduction of humidity leads to a further increase of adhesion due to hydrogen bonds bridged by water molecules. The adhesion force is maximized around 10 H2O/nm2 because as the humidity increases, hydrogen bond interactions are saturated, whereas the Van der Waals interactions decrease due to thicker water layer. It is discussed that consideration of the capillary force for paper may result in different adhesion response that reflects more realistic situation.
- 1 December 2019
- Published by Elsevier in Applied Surface Science
- Vol. 496
Adsorption characteristics of silane-functionalized perfluoropolyether on hydroxylated glassy silica surfaces: A multiscale approach
- 1 December 2019
- Published by Elsevier in Applied Surface Science
- Vol. 496
Adsorption characteristics of silane-functionalized perfluoropolyether on hydroxylated glassy silica surfaces: A multiscale approach
- 26 August 2019
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 1 (10) , 2613-2621
Enhancement of Adhesion Strength of Perfluoroalkylpolyethers on Rough Glassy Silica for Antismudge Coatings
- 26 August 2019
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 1 (10) , 2613-2621
Enhancement of Adhesion Strength of Perfluoroalkylpolyethers on Rough Glassy Silica for Antismudge Coatings