RSRichard D. Smith

Richard D. Smith

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Richard D. Smith has a total of 18 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Fully dry-processed positive-tone electron beam lithography using myo-inositol

    by R. D. Smith, A. Scherer

    The development of fully vacuum-compatible lithographic processes presents an avenue for enhancing throughput in microfabrication and avoiding the limitations imposed by wet-chemical processing. While novel negative-tone, all-vacuum processes have emerged, a positive-tone equivalent has remained elusive. This article describes early assessments of myo-inositol as a fully dry-processed, positive-tone electron-beam-sensitive film. The film is deposited via thermal vapor deposition, exposed with an electron beam at 3.6 nC/cm, and developed by heating the substrate in vacuum at 125 °C. This process preferentially removes the exposed material, and we demonstrate the fabrication of 50 nm lines at 200 nm pitch. While limited in etch resistance, this work contributes a stepping stone toward positive-tone, fully dry, vacuum cluster tool fabrication.

  • Positive electron beam resists for lithography below 5 nm

    by Axel Scherer, Richard Smith

    We compare two promising new positive self-developing electron beam resists that enable the direct patterning of nanostructures at the 1–5 nm scale. Myo-inositol is a positive organic resist that can be exposed to provide line and dot gratings with 8 nm pitch at a dose of 6 nC/cm. YbF2 provides better resolution in thick films as it is mechanically stronger, and we show line and dot gratings with 5 nm pitch at a dose of 80 nC/cm. Both of these resists were deposited by vapor deposition, and their exposure conditions were compared by exposing and imaging resist patterns in a scanning transmission electron microscope with a 0.2 nm spot size at 40–160 kV. 5 nm feature sizes were demonstrated in 90–100 nm thick layers of both materials.


  • Patterned thin film enzyme electrodes via spincoating and glutaraldehyde vapor crosslinking: towards scalable fabrication of integrated sensor-on-CMOS devices

    by Dvin Adalian, Xiomi Madero, Samson Chen, Musab Jilani, Richard D. Smith, Songtai Li, Christin Ahlbrecht, Juan Cardenas, Abhinav Agarwal, Azita Emami, et al.

    Effective continuous glucose monitoring solutions require consistent sensor performance over the lifetime of the device, a manageable variance between devices, and the capability of high volume, low cost production. Here we present a novel and microfabrication-compatible method of depositing and stabilizing enzyme layers on top of planar electrodes that can aid in the mass production of sensors while also improving their consistency. This work is focused on the fragile biorecognition layer as that has been a critical difficulty in the development of microfabricated sensors. We test this approach with glucose oxidase (GOx) and evaluate the sensor performance with amperometric measurements of in vitro glucose concentrations. Spincoating was used to deposit a uniform enzyme layer across a wafer, which was subsequently immobilized via glutaraldehyde vapor crosslinking and patterned via liftoff. This yielded an approximately 300 nm thick sensing layer which was applied to arrays of microfabricated platinum electrodes built on blank wafers. Taking advantage of their planar array format, measurements were then performed in high-throughput parallel instrumentation. Due to their thin structure, the coated electrodes exhibited subsecond stabilization times after the bias potential was applied. The deposited enzyme layers were measured to provide a sensitivity of 2.3 ± 0.2 μA mM−1 mm−2 with suitable saturation behavior and minimal performance shift observed over extended use. The same methodology was then demonstrated directly on top of wireless CMOS potentiostats to build a monolithic sensor with similar measured performance. This work demonstrates the effectiveness of the combination of spincoating and vapor stabilization processes for wafer scale enzymatic sensor functionalization and the potential for scalable fabrication of monolithic sensor-on-CMOS devices.


  • Open Access

    Robotic multi-probe single-actuator inchworm neural microdrive

    by Richard D Smith, Ilya Kolb, Shinsuke Tanaka, Albert K Lee, Timothy D Harris, Mladen Barbic

    A wide range of techniques in neuroscience involve placing individual probes at precise locations in the brain. However, large-scale measurement and manipulation of the brain using such methods have been severely limited by the inability to miniaturize systems for probe positioning. Here, we present a fundamentally new, remote-controlled micropositioning approach composed of novel phase-change material-filled resistive heater micro-grippers arranged in an inchworm motor configuration. The microscopic dimensions, stability, gentle gripping action, individual electronic control, and high packing density of the grippers allow micrometer-precision independent positioning of many arbitrarily shaped probes using a single piezo actuator. This multi-probe single-actuator design significantly reduces the size and weight and allows for potential automation of microdrives. We demonstrate accurate placement of multiple electrodes into the rat hippocampus in vivo in acute and chronic preparations. Our robotic microdrive technology should therefore enable the scaling up of many types of multi-probe applications in neuroscience and other fields.