QWQinghua Wang

Qinghua Wang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Qinghua Wang has a total of 10 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Extrusion Deformation Mechanism of Mg-8.5Al-1Zn Alloy for Dissolvable Bridge Plugs

    by Qinghua Wang, Lifeng Ma, Yanchun Zhu, Liang Ma

    To address the problems of coarse grains and unsatisfactory mechanical properties of as-cast Mg-8.5Al-1Zn alloy, which hinder its application in dissolvable bridge plugs, this study took the alloy as the research object and subjected it to plastic deformation via hot extrusion with an extrusion ratio of 12. Through the use of Combined Electron Backscatter Diffraction (EBSD) and Transmission Electron Microscopy (TEM) Testing and Characterization Techniques, the macroscopic mechanical properties, microstructural evolution, and extrusion deformation mechanism of the alloy in both as-cast and as-extruded states were systematically investigated. The results indicate that hot extrusion deformation significantly enhances the comprehensive mechanical properties of the alloy. Compared with the as-cast alloy, the tensile strength, yield strength, and elongation of the as-extruded alloy are increased by 104.0%, 314.9%, and 166.7%, respectively, with the static toughness increasing by 809.1%. The as-cast alloy exhibits coarse grains, Al element segregation, and high-density dislocations. After hot extrusion, dynamic recrystallization dominates the grain refinement, reducing the grain size by approximately 60%. Solute atoms precipitate to form multiphase structures and coherent nano-scale precipitates, along with the formation of tensile twins and a weakened bimodal texture. The improved yield strength of the as-extruded alloy stems from the synergistic effect of multiple strengthening mechanisms, among which precipitation strengthening induced by nano-precipitates is the primary contributor. The enhanced plasticity is attributed to grain refinement and texture regulation. This study clarifies the extrusion deformation mechanism of the Mg-8.5Al-1Zn alloy for dissolvable bridge plugs and verifies the rationality of the hot extrusion process with an extrusion ratio of 12, providing technical support for its industrial application in dissolvable bridge plugs and the performance regulation of similar dissolvable magnesium alloys.

  • Open Access

    Study of Corrosion Behavior of Mg–Gd-Based Soluble Magnesium Alloys

    by Qinghua Wang, Zhiquan Huang, Yanchun Zhu, Ling Qin, Jingfeng Zou, Lifeng Ma

    The corrosion behavior of soluble Mg–Gd-based alloys was systematically investigated by analyzing two key aspects: environmental factors and microstructural characteristics. Environmental influences were evaluated using immersion weight loss tests under varying Cl− concentrations and temperature conditions. From a microstructural perspective, the study examined the impact of different initial microstructural morphologies on corrosion performance. The second-phase compound Mg5Gd, formed in alloys prepared via melting, was subjected to both immersion weight loss and electrochemical testing. The results demonstrated that corrosion rates increased with higher Cl− concentrations and elevated temperatures, albeit in a nonlinear manner. Notably, significant effects on corrosion rates were observed in the Cl−concentration range of 1% to 3% and at temperatures between 75 °C and 100 °C. Additionally, the dissolution rate of the alloy increased markedly from 8.37 mg/cm2/h in the as-cast state to 43.85 mg/cm2/h following extrusion combined with perforation deformation. Microstructural analysis revealed that the extrusion process disrupted the coarse, reticulated second-phase structure observed in the as-cast state, thereby diminishing its corrosion-inhibiting properties. Electrochemical testing further confirmed that the Mg5Gd second phase, formed through the incorporation of the rare-earth element Gd, exhibited high electrochemical activity.


  • Open Access

    Study of Corrosion Behavior of Mg-Gd Based Soluble Magnesium Alloys

    by Qinghua Wang, Lifeng Ma, Zhiquan Huang, Yanchun Zhu, Jingfeng Zou, Ziliang Li, Ling Qin, Liang Ma

    In order to investigate the corrosion behavior of Mg-Gd based soluble magnesium alloy materials, two aspects, environmental factors and microstructural point of view, were discussed in this study respectively. Among them, the environmental factor aspect was carried out by immersion weight loss tests at different Cl- concentrations and different temperatures. In terms of microstructure, the influence of different initial tissue morphologies on the corrosion behavior of the alloy was mainly investigated, and the second phase Mg5Gd, prepared by melting, was subjected to immersion weight loss tests and electrochemical tests. The results show that the corrosion rate of the alloy increases with the increase of Cl- concentration and temperature, but the growth trend is not linear, in which the Cl- concentration of 1% to 3% and the temperature of 75 °C to 100 °C have a significant effect on the corrosion rate of the alloy, respectively; the dissolution rate of Mg-Gd-based soluble magnesium alloy after extrusion + perforation deformation was greatly improved from 8.37 mg/cm2/h in the as-cast state to 43.85 mg/cm2/h. Combined with the microstructure analysis, it is believed that the extrusion destroys the coarse reticulated second phase in the as-cast state organization, which reduces the corrosion-blocking network effect of the second phase; electrochemical tests showed that the second phase Mg5Gd formed after the addition of the rare earth element Gd had a high electrochemical activity.

  • Open Access

    Strain Hardening Exponent and Strain Rate Sensitivity Exponent of Cast AZ31B Magnesium Alloy

    by Yanchun Zhu, Qinghua Wang, Zhiquan Huang, Ling Qin, Ziliang Li, Lifeng Ma

    The flow curves of as-cast AZ31B magnesium alloy during high temperature deformation were obtained with a thermal compression test, and the effects of deformation amount, grain size, strain rate, and deformation temperature on the flow stress, strain rate sensitivity index, and strain hardening index were analyzed. The results showed that deformation and grain size were negatively correlated with both the strain rate sensitivity index and strain hardening index. The increase in strain rate increased the strain hardening index but made the strain rate sensitivity index show an opposite trend. Increasing temperature reduced the strain rate sensitivity index and strain hardening index but, when the temperature exceeded 700 K, the strain rate sensitivity index was no longer affected by temperature. Since the strain rate sensitivity index m and strain hardening index n are important parameters for measuring the plastic deformation of metal materials, this study has great significance for guiding the selection of process parameters in the plastic processing of as-cast AZ31 magnesium alloy.