Amir Antonio Martins Oliveira
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Amir Antonio Martins Oliveira has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Rafael Meier
Department of Mechanical Engineering, Federal University of Santa Catarina, Florianopolis, Brazil
4 shared publications - Leonel Rincón Cancino
Internal Combustion Engines Laboratory, Joinville Technological Center, LABMCI/CTJ/UFSC, Federal University of Santa Catarina, Joinville, Brazil
3 shared publications - Thiago Cardoso de Souza
Mechanical Engineering Department, Federal University of Santa Catarina 1 , Florianópolis
3 shared publications Artur Tozzi de Cantuaria Gama
Univ Fed Santa Catarina, Dept Mech Engn, BR-88040900 Florianopolis, SC, Brazil
1 shared publication- Bruno Francisco Oechsler
Federal University of Santa Catarina , Campus Universitário Reitor João David Ferreira Lima
1 shared publication - Carlos M. P. Jacome
Internal Combustion Engines Laboratory, Joinville Technological Center, LABMCI/CTJ/UFSC, Federal University of Santa Catarina, Joinville, Brazil
1 shared publication
Latest Publications
- 1 November 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (11)
Influence of inflow spatial modulation in turbulent premixed Bunsen flames
Large-scale flow modulation can enhance turbulent transport, but its effect on premixed-flame propagation depends on how the imposed spatial scales interact with the flame front. This paper examines the scale-dependent response of premixed methane–air slot Bunsen flames to coherent spatial modulation of the turbulent inflow. Direct numerical simulations combined with a flamelet-based combustion model (flamelet generated manifold) are performed for lean (ϕ=0.7), stoichiometric (ϕ=1.0), and rich (ϕ=1.3) mixtures. The flame response is evaluated in terms of flame-front thickness, curvature, wrinkling, global burning velocity, and flame height. The results show a strongly non-monotonic dependence on the modulation scale. For a perturbation scale of the order of the burner slot width, the maximum global curvature and burning velocity are obtained, while the minimum flame height occurs simultaneously. For the lean flame, the global burning velocity increases from ∼2.1 times the corresponding laminar burning velocity in the unmodulated reference case to 3.35 times the laminar value under the largest-scale modulation. Intermediate modulation scales generate the largest global wrinkling, whereas progressively smaller-scale perturbations produce burning velocity, curvature, and flame height values that approach those of the unmodulated reference flame. In contrast, the mean flame-front thickness changes only moderately, indicating that the modulation primarily alters the global flame geometry rather than the internal flame structure. Compared with the other mixtures, the lean flame exhibits the strongest relative sensitivity to the imposed modulation. These findings demonstrate that coherent inflow modulation can selectively influence turbulent flame propagation by targeting appropriate flow scales.
- 1 November 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (11)
Influence of inflow spatial modulation in turbulent premixed Bunsen flames
Large-scale flow modulation can enhance turbulent transport, but its effect on premixed-flame propagation depends on how the imposed spatial scales interact with the flame front. This paper examines the scale-dependent response of premixed methane–air slot Bunsen flames to coherent spatial modulation of the turbulent inflow. Direct numerical simulations combined with a flamelet-based combustion model (flamelet generated manifold) are performed for lean (ϕ=0.7), stoichiometric (ϕ=1.0), and rich (ϕ=1.3) mixtures. The flame response is evaluated in terms of flame-front thickness, curvature, wrinkling, global burning velocity, and flame height. The results show a strongly non-monotonic dependence on the modulation scale. For a perturbation scale of the order of the burner slot width, the maximum global curvature and burning velocity are obtained, while the minimum flame height occurs simultaneously. For the lean flame, the global burning velocity increases from ∼2.1 times the corresponding laminar burning velocity in the unmodulated reference case to 3.35 times the laminar value under the largest-scale modulation. Intermediate modulation scales generate the largest global wrinkling, whereas progressively smaller-scale perturbations produce burning velocity, curvature, and flame height values that approach those of the unmodulated reference flame. In contrast, the mean flame-front thickness changes only moderately, indicating that the modulation primarily alters the global flame geometry rather than the internal flame structure. Compared with the other mixtures, the lean flame exhibits the strongest relative sensitivity to the imposed modulation. These findings demonstrate that coherent inflow modulation can selectively influence turbulent flame propagation by targeting appropriate flow scales.
- Open Access
- 4 August 2026
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 48 (9) , 611
Predicting the combustion behavior of straight soybean oil/diesel blends: an integrated numerical and experimental assessment
This study presents a numerical characterization of the combustion process of straight soybean oil (SSO)/diesel blends using the AVL BOOST™ engine model. Validated against experimental data from a single-cylinder Yanmar YT22E engine, the work investigates four blend compositions (100% diesel, 50% diesel + 50% straight soybean oil, and 20% diesel + 80% straight soybean oil) at pre-heating temperatures of $$25^\circ$$ C and $$85^\circ$$ C and three engine speeds (1800, 2100 and 2200 rpm). Numerical simulations successfully predicted performance trends, revealing a decrease in injected fuel mass per cycle (IMFC) of up to 13% at 2200 rpm for pre-heated blends. Although the model estimated lower brake power and torque, with discrepancies ranging from 2.7% to 9.0% attributed to comprehensive manifold heat loss modeling, the combustion phasing (CA10 and CA50) and heat release rate (HRR) showed high correlation with experimental benchmarks. The results confirm that methyl linoleate is an effective surrogate for soybean oil in zero-dimensional modeling, providing a robust framework for predicting the behavior of high-viscosity biofuels.- 4 August 2026
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 48 (9) , 611
Open AccessPredicting the combustion behavior of straight soybean oil/diesel blends: an integrated numerical and experimental assessment
This study presents a numerical characterization of the combustion process of straight soybean oil (SSO)/diesel blends using the AVL BOOST™ engine model. Validated against experimental data from a single-cylinder Yanmar YT22E engine, the work investigates four blend compositions (100% diesel, 50% diesel + 50% straight soybean oil, and 20% diesel + 80% straight soybean oil) at pre-heating temperatures of $$25^\circ$$ C and $$85^\circ$$ C and three engine speeds (1800, 2100 and 2200 rpm). Numerical simulations successfully predicted performance trends, revealing a decrease in injected fuel mass per cycle (IMFC) of up to 13% at 2200 rpm for pre-heated blends. Although the model estimated lower brake power and torque, with discrepancies ranging from 2.7% to 9.0% attributed to comprehensive manifold heat loss modeling, the combustion phasing (CA10 and CA50) and heat release rate (HRR) showed high correlation with experimental benchmarks. The results confirm that methyl linoleate is an effective surrogate for soybean oil in zero-dimensional modeling, providing a robust framework for predicting the behavior of high-viscosity biofuels. - Open Access
- 18 November 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (47) , 57724-57740
Unraveling Heat Integration Opportunities in SOFC–Ethanol Reformer Systems across Steam Reforming, Partial Oxidation, and Autothermal Reforming Pathways
Heat integration is essential to enhance the efficiency of solid oxide fuel cell (SOFC) systems coupled with ethanol reformers, being fundamental to enable their use in onboard applications and distributed power systems. However, a unified, system-level comparison of steam reforming (SR), partial oxidation (POX), and autothermal reforming (ATR) within a single modeling and analysis of heat integration opportunities has been lacking. This study addresses this gap by developing a simulation framework that combines a validated lumped SOFC model with a flowsheet simulation environment to systematically assess the thermal behavior of SOFC–reformer configurations. A design of experiments approach, based on a face-centered central composite design, was employed to generate discrete simulation data, which were subsequently analyzed using analysis of variance (ANOVA) and response surface methodology (RSM). This enabled the construction of metamodels linking key process variables such as reformer and SOFC temperatures, operating pressure, water-to-ethanol, and oxygen-to-ethanol molar ratios to system responses such as electrical efficiency and thermal duties. Results show that the SOFC consistently acts as a net heat source, producing surplus heat relative to the reformer demand, while the temperature gradient between components favors internal recovery. Conditions close to the SR regime were found to maximize the electrical efficiency (up to 36%) and minimize external heating requirements. Based on these insights, a heat exchanger network (HEN) was proposed by using the Pinch method and validated in the flowsheet simulation. The proposed HEN fully satisfied the heating requirements of the system, eliminating the need for hot utilities and improving electrical efficiency from 36 to 52%. Overall, the study demonstrates that thermally integrated SOFC–ethanol reformer systems can achieve self-sustaining operation under steady-state conditions. The proposed unified modeling framework provides new insights into the thermodynamic coupling between ethanol reformers and SOFCs, highlighting ethanol as a viable renewable fuel and advancing the design of compact, fuel-flexible energy technologies for high-efficiency, and clean power generation.
- 18 November 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (47) , 57724-57740
Open AccessUnraveling Heat Integration Opportunities in SOFC–Ethanol Reformer Systems across Steam Reforming, Partial Oxidation, and Autothermal Reforming Pathways
Heat integration is essential to enhance the efficiency of solid oxide fuel cell (SOFC) systems coupled with ethanol reformers, being fundamental to enable their use in onboard applications and distributed power systems. However, a unified, system-level comparison of steam reforming (SR), partial oxidation (POX), and autothermal reforming (ATR) within a single modeling and analysis of heat integration opportunities has been lacking. This study addresses this gap by developing a simulation framework that combines a validated lumped SOFC model with a flowsheet simulation environment to systematically assess the thermal behavior of SOFC–reformer configurations. A design of experiments approach, based on a face-centered central composite design, was employed to generate discrete simulation data, which were subsequently analyzed using analysis of variance (ANOVA) and response surface methodology (RSM). This enabled the construction of metamodels linking key process variables such as reformer and SOFC temperatures, operating pressure, water-to-ethanol, and oxygen-to-ethanol molar ratios to system responses such as electrical efficiency and thermal duties. Results show that the SOFC consistently acts as a net heat source, producing surplus heat relative to the reformer demand, while the temperature gradient between components favors internal recovery. Conditions close to the SR regime were found to maximize the electrical efficiency (up to 36%) and minimize external heating requirements. Based on these insights, a heat exchanger network (HEN) was proposed by using the Pinch method and validated in the flowsheet simulation. The proposed HEN fully satisfied the heating requirements of the system, eliminating the need for hot utilities and improving electrical efficiency from 36 to 52%. Overall, the study demonstrates that thermally integrated SOFC–ethanol reformer systems can achieve self-sustaining operation under steady-state conditions. The proposed unified modeling framework provides new insights into the thermodynamic coupling between ethanol reformers and SOFCs, highlighting ethanol as a viable renewable fuel and advancing the design of compact, fuel-flexible energy technologies for high-efficiency, and clean power generation.
- Open Access
- 17 June 2024
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 46 (8) , 1
Correction: Effects of intrinsic instabilities in the local burning rate of lean premixed hydrogen/air laminar flames
- 17 June 2024
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 46 (8) , 1
Open AccessCorrection: Effects of intrinsic instabilities in the local burning rate of lean premixed hydrogen/air laminar flames
- 5 February 2024
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 46 (3) , 1-14
Effects of intrinsic instabilities in the local burning rate of lean premixed hydrogen/air laminar flames
- 5 February 2024
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 46 (3) , 1-14
Effects of intrinsic instabilities in the local burning rate of lean premixed hydrogen/air laminar flames