Giulia Ronconi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Giulia Ronconi has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Francesco Mollica
Department of Engineering, University of Ferrara, Via Saragat 1, 44122 Ferrara, Italy
3 shared publications - Marco Zanelli
Department of Engineering, University of Ferrara, Via Saragat 1, 44122 Ferrara, Italy
3 shared publications - Valentina Mazzanti
Department of Engineering, University of Ferrara, Via Saragat 1, 44122 Ferrara, Italy
3 shared publications - Andrea D'IOrio
Department of Chemical, Pharmaceutical and Agricultural Sciences, University of Ferrara, Via L. Borsari 46, 44121 Ferrara, Italy
2 shared publications - Monica Bertoldo
Department of Chemical Pharmaceutical and Agricultural Sciences University of Ferrara Ferrara Italy
2 shared publications - Nicola Pritoni
Department of Engineering, University of Ferrara, Via Saragat 1, 44122 Ferrara, Italy
2 shared publications
Latest Publications
- Open Access
Mechanical Recycling of a Short Carbon Fiber Reinforced Polyamide 6 in 3D Printing: Effects on Mechanical Properties
Mechanical recycling of Fused Deposition Modeling 3D printing materials is very attractive for the circular economy. In this paper, the tensile properties of a virgin and a one-time-recycled short carbon fiber reinforced polyamide, coming from 3D printing scrap and failed parts, were evaluated. Anisotropy was taken into account properly by using characterization methods that are typical of composites. Rheological properties were obtained with a parallel plate rheometer in oscillatory mode, and thermal properties were investigated based on thermogravimetric analysis and differential scanning calorimetry. A decrease in the average molecular weight of the recycled material, indicated by the rheological measurements, induced brittleness. Nevertheless, the stiffness and yield strength of the 3D printed parts made with the recycled material were higher than those made with the virgin one. Since this behavior could not be explained based on an increase in crystallinity or a relevant decrease in the void content, a feasible explanation is proposed with an increase of the interlayer and intralayer adhesion quality. In any case, the recycled polyamide filament can be successfully reused in Fused Deposition Modeling 3D printing, even when significant mechanical properties are required, but attention must be paid to a certain decrease in ductility.
Open AccessMechanical Recycling of a Short Carbon Fiber Reinforced Polyamide 6 in 3D Printing: Effects on Mechanical Properties
Mechanical recycling of Fused Deposition Modeling 3D printing materials is very attractive for the circular economy. In this paper, the tensile properties of a virgin and a one-time-recycled short carbon fiber reinforced polyamide, coming from 3D printing scrap and failed parts, were evaluated. Anisotropy was taken into account properly by using characterization methods that are typical of composites. Rheological properties were obtained with a parallel plate rheometer in oscillatory mode, and thermal properties were investigated based on thermogravimetric analysis and differential scanning calorimetry. A decrease in the average molecular weight of the recycled material, indicated by the rheological measurements, induced brittleness. Nevertheless, the stiffness and yield strength of the 3D printed parts made with the recycled material were higher than those made with the virgin one. Since this behavior could not be explained based on an increase in crystallinity or a relevant decrease in the void content, a feasible explanation is proposed with an increase of the interlayer and intralayer adhesion quality. In any case, the recycled polyamide filament can be successfully reused in Fused Deposition Modeling 3D printing, even when significant mechanical properties are required, but attention must be paid to a certain decrease in ductility.
- Open Access
3D Printing of Continuous Basalt Fiber-Reinforced Composites: Characterization of the In-Plane Mechanical Properties and Anisotropy Evaluation
Usage of continuous fibers as a reinforcement would definitely increase the mechanical properties of 3D-printed materials. The result is a continuous fiber-reinforced composite obtained by additive manufacturing that is not limited to prototyping or non-structural applications. Among the available continuous reinforcing fibers, basalt has not been extensively studied in 3D printing. This material is attractive due to its natural origin, good mechanical properties, impact strength, and high chemical and thermal resistance. In this work, a continuous basalt fiber co-extruded composite obtained by fused filament fabrication was characterized both thermally and mechanically, concerning the in-plane tensile properties. The degree of anisotropy of the material was also assessed, both qualitatively and quantitatively. The 3D-printed composite showed longitudinal properties, which were 15 times higher than the pure matrix, thus meeting structural requirements. On the other hand, transverse and shear properties were much lower than longitudinal ones, thus leading to a strongly anisotropic material. This was also confirmed by the anisotropy evaluation that was performed numerically and graphically using an innovative approach. This behavior affects the design of 3D-printed parts; thus, an optimized continuous fiber deposition is necessary for structural applications.
Open Access3D Printing of Continuous Basalt Fiber-Reinforced Composites: Characterization of the In-Plane Mechanical Properties and Anisotropy Evaluation
Usage of continuous fibers as a reinforcement would definitely increase the mechanical properties of 3D-printed materials. The result is a continuous fiber-reinforced composite obtained by additive manufacturing that is not limited to prototyping or non-structural applications. Among the available continuous reinforcing fibers, basalt has not been extensively studied in 3D printing. This material is attractive due to its natural origin, good mechanical properties, impact strength, and high chemical and thermal resistance. In this work, a continuous basalt fiber co-extruded composite obtained by fused filament fabrication was characterized both thermally and mechanically, concerning the in-plane tensile properties. The degree of anisotropy of the material was also assessed, both qualitatively and quantitatively. The 3D-printed composite showed longitudinal properties, which were 15 times higher than the pure matrix, thus meeting structural requirements. On the other hand, transverse and shear properties were much lower than longitudinal ones, thus leading to a strongly anisotropic material. This was also confirmed by the anisotropy evaluation that was performed numerically and graphically using an innovative approach. This behavior affects the design of 3D-printed parts; thus, an optimized continuous fiber deposition is necessary for structural applications.
- Open Access
A Post-Processing Method for Improving the Mechanical Properties of Fused-Filament-Fabricated 3D-Printed Parts
Fused-filament fabrication is one of the most popular 3D printing techniques for thermoplastic materials because it is easy to use and is low-cost. On the other hand, it has the great limit of being suitable only for developing prototypes, because the printed object generally has low mechanical properties, and this prevents its use in structural applications. To solve this issue, the scientific literature has mainly focused on the optimization of the printing parameters and on performing some post-printing treatments, e.g., annealing, but despite some results being very promising, the topic has not yet been exhaustively investigated. In this paper, a post-printing treatment was studied that was based on two subsequent stages of remelting and compaction within a mold made of a granular material. The material chosen for this study was a green composite made of poly-(lactic acid) and poly-(hydroxyalkanoate) filled with wood fibers. The density, mechanical properties in terms of tension and microscopic observations were used to evaluate the treatment effectiveness. The main results were that voids were reduced, and the quality of the interlayer welding was increased, and this improved the mechanical properties, both in terms of stiffness and strength. In particular, the initial specimens displayed remarkable anisotropy, being stronger and stiffer in the longitudinal direction. After the post-processing treatment, despite the longitudinal properties having a very limited increase, the transversal properties increased significantly until they reached the longitudinal properties, thus leading to a more isotropic material.
Open AccessA Post-Processing Method for Improving the Mechanical Properties of Fused-Filament-Fabricated 3D-Printed Parts
Fused-filament fabrication is one of the most popular 3D printing techniques for thermoplastic materials because it is easy to use and is low-cost. On the other hand, it has the great limit of being suitable only for developing prototypes, because the printed object generally has low mechanical properties, and this prevents its use in structural applications. To solve this issue, the scientific literature has mainly focused on the optimization of the printing parameters and on performing some post-printing treatments, e.g., annealing, but despite some results being very promising, the topic has not yet been exhaustively investigated. In this paper, a post-printing treatment was studied that was based on two subsequent stages of remelting and compaction within a mold made of a granular material. The material chosen for this study was a green composite made of poly-(lactic acid) and poly-(hydroxyalkanoate) filled with wood fibers. The density, mechanical properties in terms of tension and microscopic observations were used to evaluate the treatment effectiveness. The main results were that voids were reduced, and the quality of the interlayer welding was increased, and this improved the mechanical properties, both in terms of stiffness and strength. In particular, the initial specimens displayed remarkable anisotropy, being stronger and stiffer in the longitudinal direction. After the post-processing treatment, despite the longitudinal properties having a very limited increase, the transversal properties increased significantly until they reached the longitudinal properties, thus leading to a more isotropic material.