Imjeong H.-S. Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Imjeong H.-S. Yang has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Hee Jin Jeong
Nano Hybrid Technology Research Center, Creative and Fundamental Research Division, Korea Electrotechnology Research Institute (KERI), Changwon 51543, Republic of Korea
5 shared publications Jae-Won Lee
Department of Physics, Pusan National University, Busan 46241, South Korea
5 shared publicationsJuhee Kim
Nano Hybrid Technology Research Center, Creative and Fundamental Research Division, Korea Electrotechnology Research Institute (KERI), Changwon 51543, Republic of Korea
5 shared publicationsJi Hye Kwak
Electrical Environment Research Center, Power Grid Research Division, Korea Electrotechnology Research Institute (KERI), Changwon 51543, Republic of Korea
4 shared publicationsKyong-Soo Hong
Busan Center, Korea Basic Science Institute (KBSI), Busan 46742, South Korea
4 shared publications- Joong Tark Han
Nano Hybrid Technology Research Center, Creative and Fundamental Research Division, Korea Electrotechnology Research Institute (KERI), Changwon 51543, Republic of Korea
2 shared publications
Latest Publications
- 20 January 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 13 (9) , 4576-4582
Photo-thermally controlled Cu nanoparticles density in SWCNT/Cu nanocomposites-based flexible EMI shielding electrodes
In this study, single-walled carbon nanotube (SWCNT)/Cu nanocomposites were systematically synthesized from oxidized SWCNTs and Cu formate via photothermal heating.
- 20 January 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 13 (9) , 4576-4582
Photo-thermally controlled Cu nanoparticles density in SWCNT/Cu nanocomposites-based flexible EMI shielding electrodes
In this study, single-walled carbon nanotube (SWCNT)/Cu nanocomposites were systematically synthesized from oxidized SWCNTs and Cu formate via photothermal heating.
- 6 January 2025
- Published by Springer Nature in Journal of the Korean Physical Society
- Vol. 86 (4) , 292-297
Efficient photothermal annealing of carbon quantum dots
- 6 January 2025
- Published by Springer Nature in Journal of the Korean Physical Society
- Vol. 86 (4) , 292-297
Efficient photothermal annealing of carbon quantum dots
- Open Access
- 3 April 2024
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 14 (16) , 11524-11532
Highly emissive blue graphene quantum dots with excitation-independent emission via ultrafast liquid-phase photoreduction
Graphene oxide quantum dots (GOQDs) are promising candidates for biomedical applications since they have lower toxicity and higher biocompatibility than traditional semiconductor quantum dots.
- 3 April 2024
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 14 (16) , 11524-11532
Open AccessHighly emissive blue graphene quantum dots with excitation-independent emission via ultrafast liquid-phase photoreduction
Graphene oxide quantum dots (GOQDs) are promising candidates for biomedical applications since they have lower toxicity and higher biocompatibility than traditional semiconductor quantum dots.
- 19 May 2023
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 11 (22) , 7383-7388
Photo-chemically assisted redox-nano welding for highly conductive and robust copper-based electrodes
In this study, high-quality conductive electrodes were fabricated by improving the sintering efficiency and packing density of Cu sub-microparticle (sub-μP) electrodes through IPL sintering with redox reaction-induced nano-welding. This process includes both pre-oxidation and photothermal chemical reduction. The pre-oxidation in the Cu sub-μP electrodes can easily be triggered (within a few seconds) via a hot air treatment (500 °C). The oxidized Cu sub-μP electrodes are reduced and sintered simultaneously through a photothermal chemical reaction during the IPL sintering process. Cu nanoparticles, which are newly formed in the photothermal chemical reduction process, play an important role as interconnection materials between Cu sub-μPs during the IPL sintering process. The effect of exposure time and temperature in the hot air treatment on the oxidation properties of Cu sub-μPs are investigated systematically using noncontact spectroscopic temperature-sensing techniques and X-ray diffraction analysis. After IPL sintering, the conductive Cu sub-μP electrodes showed highly sintered morphologies, which resulted in extremely low electric resistivity (8.34 μΩ cm) under optimal conditions.
- 19 May 2023
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 11 (22) , 7383-7388
Photo-chemically assisted redox-nano welding for highly conductive and robust copper-based electrodes
In this study, high-quality conductive electrodes were fabricated by improving the sintering efficiency and packing density of Cu sub-microparticle (sub-μP) electrodes through IPL sintering with redox reaction-induced nano-welding. This process includes both pre-oxidation and photothermal chemical reduction. The pre-oxidation in the Cu sub-μP electrodes can easily be triggered (within a few seconds) via a hot air treatment (500 °C). The oxidized Cu sub-μP electrodes are reduced and sintered simultaneously through a photothermal chemical reaction during the IPL sintering process. Cu nanoparticles, which are newly formed in the photothermal chemical reduction process, play an important role as interconnection materials between Cu sub-μPs during the IPL sintering process. The effect of exposure time and temperature in the hot air treatment on the oxidation properties of Cu sub-μPs are investigated systematically using noncontact spectroscopic temperature-sensing techniques and X-ray diffraction analysis. After IPL sintering, the conductive Cu sub-μP electrodes showed highly sintered morphologies, which resulted in extremely low electric resistivity (8.34 μΩ cm) under optimal conditions.
- 14 November 2022
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 10 (45) , 17336-17342
Hierarchical copper nanostructures synthesized on microparticles for improved photothermal conversion in photonic sintering of copper-based printed electrodes
Photonic sintering of Cu-particle-based printed patterns using intense pulsed light (IPL) is a promising route to the large-scale fabrication of printed electronics for commercial applications. Despite the significant advantages of photonic sintering, which include the process being ultrafast, extremely low-cost, and eco-friendly, realizing a high-conductivity Cu-printed electrode remains a major challenge. In particular, low light absorption caused by the low surface plasmon density of Cu particles is the origin of insufficient temperature increase even after IPL irradiation. In this study, hierarchical nanostructured (HN) Cu microparticles (Cu μPs) with improved light absorption ability and lower surface melting point were prepared for the fabrication of high-conductivity Cu electrodes by using IPL sintering. HN-Cu μPs of uniform size were synthesized using a wet chemical hydrothermal method, with Cu(II) nitrate trihydrate, ethylenediamine (EDA), and Cu μPs as the precursor, structure-directing agent, and template, respectively. The morphology of the hierarchical nanostructures could be readily tuned by varying the synthesis time and the amounts of the precursor and EDA. On the basis of ultraviolet-visible spectroscopy, X-ray diffraction, and temperature measurements, the enhanced light absorption in the visible wavelength range was ascribed to the increase in the surface plasmon density of the hierarchical Cu nanostructures. After photonic sintering, the HN-Cu μP-based printed patterns showed highly dense Cu morphologies, which resulted in an extremely low electrical resistivity of 16 μΩ cm for IPL with an energy density of 7 J cm−2.
- 14 November 2022
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 10 (45) , 17336-17342
Hierarchical copper nanostructures synthesized on microparticles for improved photothermal conversion in photonic sintering of copper-based printed electrodes
Photonic sintering of Cu-particle-based printed patterns using intense pulsed light (IPL) is a promising route to the large-scale fabrication of printed electronics for commercial applications. Despite the significant advantages of photonic sintering, which include the process being ultrafast, extremely low-cost, and eco-friendly, realizing a high-conductivity Cu-printed electrode remains a major challenge. In particular, low light absorption caused by the low surface plasmon density of Cu particles is the origin of insufficient temperature increase even after IPL irradiation. In this study, hierarchical nanostructured (HN) Cu microparticles (Cu μPs) with improved light absorption ability and lower surface melting point were prepared for the fabrication of high-conductivity Cu electrodes by using IPL sintering. HN-Cu μPs of uniform size were synthesized using a wet chemical hydrothermal method, with Cu(II) nitrate trihydrate, ethylenediamine (EDA), and Cu μPs as the precursor, structure-directing agent, and template, respectively. The morphology of the hierarchical nanostructures could be readily tuned by varying the synthesis time and the amounts of the precursor and EDA. On the basis of ultraviolet-visible spectroscopy, X-ray diffraction, and temperature measurements, the enhanced light absorption in the visible wavelength range was ascribed to the increase in the surface plasmon density of the hierarchical Cu nanostructures. After photonic sintering, the HN-Cu μP-based printed patterns showed highly dense Cu morphologies, which resulted in an extremely low electrical resistivity of 16 μΩ cm for IPL with an energy density of 7 J cm−2.
- 27 July 2021
- Published by Wiley in Advanced Materials Interfaces
- Vol. 8 (16) , 2100769
Minimizing Temperature Gradient in Photonic Sintering for Defect‐Free High‐Conductivity Cu‐Based Printed Patterns by Bidirectional Irradiation
Intense pulsed light (IPL)‐induced photothermal heating is relatively effective at reducing the annealing or sintering time of metal particle‐based conductive patterns in the manufacturing of printed electronics. However, defects such as cavities, delamination, and inhomogeneous shrinkage within the sintered patterns are a well‐known problem in IPL sintering. These defects are considerably influenced by undesired temperature gradients induced inside samples during IPL sintering. To solve this undesired temperature gradient problem, we propose a bidirectional IPL (B‐IPL) sintering approach using front‐ and back‐elliptical reflectors on both sides of the printed pattern. The effects of the B‐IPL energy density and number of shots on the electrical and mechanical properties of the printed patterns were systematically investigated using noncontact spectroscopic temperature sensing techniques with a µs‐timescale infrared temperature sensor system. Cross‐sectional field emission scanning electron microscopy images indicate that B‐IPL sintering significantly enhances the densification level and sintering uniformity of printed patterns compared to conventional IPL.
- 27 July 2021
- Published by Wiley in Advanced Materials Interfaces
- Vol. 8 (16) , 2100769
Minimizing Temperature Gradient in Photonic Sintering for Defect‐Free High‐Conductivity Cu‐Based Printed Patterns by Bidirectional Irradiation
Intense pulsed light (IPL)‐induced photothermal heating is relatively effective at reducing the annealing or sintering time of metal particle‐based conductive patterns in the manufacturing of printed electronics. However, defects such as cavities, delamination, and inhomogeneous shrinkage within the sintered patterns are a well‐known problem in IPL sintering. These defects are considerably influenced by undesired temperature gradients induced inside samples during IPL sintering. To solve this undesired temperature gradient problem, we propose a bidirectional IPL (B‐IPL) sintering approach using front‐ and back‐elliptical reflectors on both sides of the printed pattern. The effects of the B‐IPL energy density and number of shots on the electrical and mechanical properties of the printed patterns were systematically investigated using noncontact spectroscopic temperature sensing techniques with a µs‐timescale infrared temperature sensor system. Cross‐sectional field emission scanning electron microscopy images indicate that B‐IPL sintering significantly enhances the densification level and sintering uniformity of printed patterns compared to conventional IPL.