Shabin Mohammed
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Shabin Mohammed has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Raed Hashaikeh
NYUAD Water Research Centre, New York University, Abu Dhabi Campus, Abu Dhabi P.O. Box 129188, United Arab Emirates
3 shared publications - Jamaliah Aburabie
NYUAD Water Research Center, Department of Engineering, New York University Abu Dhabi, Abu Dhabi P.O. Box 129188, United Arab Emirates
2 shared publications - Hai Tang
School of Chemical and Environmental Engineering, Anhui Polytechnic University, Wuhu 241000, China
1 shared publication - Haya Nassrullah
NYUAD Water Research Center, Department of Engineering, New York University Abu Dhabi, Abu Dhabi P.O. Box 129188, United Arab Emirates
1 shared publication Jamaliah Aburabie
NYUAD Water Research Center, Department of Engineering, New York University Abu Dhabi, Abu Dhabi, United Arab Emirates
1 shared publication- Kaixuan Zhu
School of Chemical and Environmental Engineering, Anhui Polytechnic University, Wuhu 241000, China
1 shared publication
Latest Publications
- Open Access
- 31 July 2023
- Published by Springer Nature in npj Clean Water
- Vol. 6 (1) , 1-12
Facile morphological tuning of thin film composite membranes for enhanced desalination performance
Polyamide (PA) membranes with a thin selective layer have been widely investigated for desalination and water treatment. Several modifications have been proposed over the years to tailor the morphology of such thin film composite (TFC) membranes by altering the support and/or selective layers to achieve superior performance. In this study, a facile approach towards fabricating a highly wrinkled selective layer has been demonstrated through bio-inspired modification of the support layer with Y-type zeolites. Results showed that incorporating zeolites in a smaller dimension (200 nm) produced by a unique ball milling technique is favorable for a defect-free selective layer in comparison to larger commercial zeolites. PA membranes formed by the interfacial polymerization (IP) of Piperazine (PIP) and 1,3,5-Benzenetricarbonyl trichloride (TMC) revealed highly wrinkled morphology due to the presence of zeolites in the TFC interlayer. At optimum fabrication conditions, the membrane exhibited a fast transport of 22.5 ± 2.2 Lm-2h-1bar-1 with a salt rejection of 48.6, 91.3, 99.1, and 99.5% for NaCl, MgCl2, MgSO4, and Na2SO4, respectively. Besides the unique preparation of zeolites in smaller dimensions, the novelty of this study lies in the facile membrane pretreatment before IP to achieve wrinkled PA membranes for enhanced nanofiltration performance.
- 31 July 2023
- Published by Springer Nature in npj Clean Water
- Vol. 6 (1) , 1-12
Open AccessFacile morphological tuning of thin film composite membranes for enhanced desalination performance
Polyamide (PA) membranes with a thin selective layer have been widely investigated for desalination and water treatment. Several modifications have been proposed over the years to tailor the morphology of such thin film composite (TFC) membranes by altering the support and/or selective layers to achieve superior performance. In this study, a facile approach towards fabricating a highly wrinkled selective layer has been demonstrated through bio-inspired modification of the support layer with Y-type zeolites. Results showed that incorporating zeolites in a smaller dimension (200 nm) produced by a unique ball milling technique is favorable for a defect-free selective layer in comparison to larger commercial zeolites. PA membranes formed by the interfacial polymerization (IP) of Piperazine (PIP) and 1,3,5-Benzenetricarbonyl trichloride (TMC) revealed highly wrinkled morphology due to the presence of zeolites in the TFC interlayer. At optimum fabrication conditions, the membrane exhibited a fast transport of 22.5 ± 2.2 Lm-2h-1bar-1 with a salt rejection of 48.6, 91.3, 99.1, and 99.5% for NaCl, MgCl2, MgSO4, and Na2SO4, respectively. Besides the unique preparation of zeolites in smaller dimensions, the novelty of this study lies in the facile membrane pretreatment before IP to achieve wrinkled PA membranes for enhanced nanofiltration performance.
- Open Access
Valorization of Seawater Reverse Osmosis Brine by Monovalent Ion-Selective Membranes through Electrodialysis
This paper proposes the use of monovalent selective electrodialysis technology to concentrate the valuable sodium chloride (NaCl) component present in seawater reverse osmosis (SWRO) brine for direct utilization in the chlor-alkali industry. To enhance monovalent selectivity, a polyamide selective layer was fabricated on commercial ion exchange membranes (IEMs) through interfacial polymerization (IP) of piperazine (PIP) and 1,3,5-Benzenetricarbonyl chloride (TMC). The IP-modified IEMs were characterized using various techniques to investigate changes in chemical structure, morphology, and surface charge. Ion chromatography (IC) analysis showed that the divalent rejection rate was more than 90% for IP-modified IEMs, compared to less than 65% for commercial IEMs. Electrodialysis results demonstrated that the SWRO brine was successfully concentrated to 14.9 g/L NaCl at a power consumption rate of 3.041 kWh/kg, indicating the advantageous performance of the IP-modified IEMs. Overall, the proposed monovalent selective electrodialysis technology using IP-modified IEMs has the potential to provide a sustainable solution for the direct utilization of NaCl in the chlor-alkali industry.
Open AccessValorization of Seawater Reverse Osmosis Brine by Monovalent Ion-Selective Membranes through Electrodialysis
This paper proposes the use of monovalent selective electrodialysis technology to concentrate the valuable sodium chloride (NaCl) component present in seawater reverse osmosis (SWRO) brine for direct utilization in the chlor-alkali industry. To enhance monovalent selectivity, a polyamide selective layer was fabricated on commercial ion exchange membranes (IEMs) through interfacial polymerization (IP) of piperazine (PIP) and 1,3,5-Benzenetricarbonyl chloride (TMC). The IP-modified IEMs were characterized using various techniques to investigate changes in chemical structure, morphology, and surface charge. Ion chromatography (IC) analysis showed that the divalent rejection rate was more than 90% for IP-modified IEMs, compared to less than 65% for commercial IEMs. Electrodialysis results demonstrated that the SWRO brine was successfully concentrated to 14.9 g/L NaCl at a power consumption rate of 3.041 kWh/kg, indicating the advantageous performance of the IP-modified IEMs. Overall, the proposed monovalent selective electrodialysis technology using IP-modified IEMs has the potential to provide a sustainable solution for the direct utilization of NaCl in the chlor-alkali industry.
- Open Access
- 5 February 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (4) , 2879
ZIF-67/SA@PVDF Ultrafiltration Membrane with Simultaneous Adsorption and Catalytic Oxidation for Dyes
Due to their stable chemical properties and complex structures, dyes are difficult to be removed from water. Herein, a ZIF-67/SA@PVDF (ZSA3@PVDF) mixed matrix membrane has been fabricated by incorporating silicon aerogel (SA) and zeolitic imidazolate framework material 67 (ZIF-67) nanoparticles in a polyvinylidene fluoride (PVDF) membrane for the removal and degradation of dyes from water. The influence of SA and ZIF-67 on the morphology and structure of the membrane was confirmed using scanning electron microscope (SEM) and atomic force microscope (AFM). In ZSA3@PVDF membrane, both SA and ZIF-67 are highly porous nanomaterials that possess good adsorption capacity, as confirmed by the Brunauer–Emmett–Teller (BET) result. In addition, the cobalt (Co) element of ZIF-67 can catalyze peroxymonosulfate (PMS) to generate strong oxidizing sulfate radicals (SO42−), contributing to improving regeneration capacity of the ZIF-67/SA@PVDF membrane. The water flux of ZSA3@PVDF membrane is 427.6 L m−2 h−1 bar−1, and the Methylene blue (MB) removal rate is higher than 99% when filtrating 100 mL MB solution (5 mg/L). The regeneration test result shows that the removal rate of the ZSA3@PVDF membrane is still above 98% after five cycles of adsorption of MB. The self-cleaning experiment shows that the adsorption of SA in the ZSA3@PVDF membrane promotes the catalytic performance of the membrane, showing a better self-cleaning ability. The ZSA3@PVDF membrane provides a new strategy for the removal of dyes in the advanced purification of dye wastewater.
- 5 February 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (4) , 2879
Open AccessZIF-67/SA@PVDF Ultrafiltration Membrane with Simultaneous Adsorption and Catalytic Oxidation for Dyes
Due to their stable chemical properties and complex structures, dyes are difficult to be removed from water. Herein, a ZIF-67/SA@PVDF (ZSA3@PVDF) mixed matrix membrane has been fabricated by incorporating silicon aerogel (SA) and zeolitic imidazolate framework material 67 (ZIF-67) nanoparticles in a polyvinylidene fluoride (PVDF) membrane for the removal and degradation of dyes from water. The influence of SA and ZIF-67 on the morphology and structure of the membrane was confirmed using scanning electron microscope (SEM) and atomic force microscope (AFM). In ZSA3@PVDF membrane, both SA and ZIF-67 are highly porous nanomaterials that possess good adsorption capacity, as confirmed by the Brunauer–Emmett–Teller (BET) result. In addition, the cobalt (Co) element of ZIF-67 can catalyze peroxymonosulfate (PMS) to generate strong oxidizing sulfate radicals (SO42−), contributing to improving regeneration capacity of the ZIF-67/SA@PVDF membrane. The water flux of ZSA3@PVDF membrane is 427.6 L m−2 h−1 bar−1, and the Methylene blue (MB) removal rate is higher than 99% when filtrating 100 mL MB solution (5 mg/L). The regeneration test result shows that the removal rate of the ZSA3@PVDF membrane is still above 98% after five cycles of adsorption of MB. The self-cleaning experiment shows that the adsorption of SA in the ZSA3@PVDF membrane promotes the catalytic performance of the membrane, showing a better self-cleaning ability. The ZSA3@PVDF membrane provides a new strategy for the removal of dyes in the advanced purification of dye wastewater.
- Open Access
Fabrication of Thin Film Composite Membranes on Nanozeolite Modified Support Layer for Tailored Nanofiltration Performance
Thin-film composite (TFC) structure has been widely employed in polymeric membrane fabrication to achieve superior performance for desalination and water treatment. In particular, TFC membranes with a thin active polyamide (PA) selective layer are proven to offer improved permeability without compromising salt rejection. Several modifications to TFCs have been proposed over the years to enhance their performance by altering the selective, intermediate, or support layer. This study proposes the modification of the membrane support using nanozeolites prepared by a unique ball milling technique for tailoring the nanofiltration performance. TFC membranes were fabricated by the interfacial polymerization of Piperazine (PIP) and 1,3,5-Benzenetricarbonyl trichloride (TMC) on Polysulfone (PSf) supports modified with nanozeolites. The nanozeolite concentration in the casting solution varied from 0 to 0.2%. Supports prepared with different nanozeolite concentrations resulted in varied hydrophilicity, porosity, and permeability. Results showed that optimum membrane performance was obtained for supports modified with 0.1% nanozeolites where pure water permeance of 17.1 ± 2.1 Lm−2 h−1 bar−1 was observed with a salt rejection of 11.47%, 33.84%, 94%, and 95.1% for NaCl, MgCl2, MgSO4, and Na2SO4 respectively.
Open AccessFabrication of Thin Film Composite Membranes on Nanozeolite Modified Support Layer for Tailored Nanofiltration Performance
Thin-film composite (TFC) structure has been widely employed in polymeric membrane fabrication to achieve superior performance for desalination and water treatment. In particular, TFC membranes with a thin active polyamide (PA) selective layer are proven to offer improved permeability without compromising salt rejection. Several modifications to TFCs have been proposed over the years to enhance their performance by altering the selective, intermediate, or support layer. This study proposes the modification of the membrane support using nanozeolites prepared by a unique ball milling technique for tailoring the nanofiltration performance. TFC membranes were fabricated by the interfacial polymerization of Piperazine (PIP) and 1,3,5-Benzenetricarbonyl trichloride (TMC) on Polysulfone (PSf) supports modified with nanozeolites. The nanozeolite concentration in the casting solution varied from 0 to 0.2%. Supports prepared with different nanozeolite concentrations resulted in varied hydrophilicity, porosity, and permeability. Results showed that optimum membrane performance was obtained for supports modified with 0.1% nanozeolites where pure water permeance of 17.1 ± 2.1 Lm−2 h−1 bar−1 was observed with a salt rejection of 11.47%, 33.84%, 94%, and 95.1% for NaCl, MgCl2, MgSO4, and Na2SO4 respectively.