Patrick P. Neumann
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Patrick P. Neumann has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Achim J. Lilienthal
Örebro University
5 shared publications Matthias Bartholmai
Bundesanstalt für Materialforschung und -prüfung (BAM), Unter den Eichen 87, Berlin, Germany
5 shared publications- Michael G. Weller
Federal Institute For Materials Research and Testing, Berlin, Germany, Germany
5 shared publications - Tino Nerger
Federal Institute For Materials Research and Testing, Berlin, Germany, Germany
5 shared publications - Detlef Lazik
Department Soil System Science, Helmholtz Centre for Environmental Research GmbH—UFZ, 06120 Halle (Saale), Germany
2 shared publications - Erik Schaffernicht
Technical University of Applied Sciences Wrzburg-Schweinfurt, Wrzburg, Germany
2 shared publications
Latest Publications
- Open Access
- 2 November 2026
- Published by MDPI AG in Preprints.org
Smartphone Colorimetry with In-Frame Color Calibration: Hue-Based Discrimination of Diesel-Type Fuels and Ethanol–Gasoline Blends
Color measurements from consumer cameras are difficult to compare because device-specific image processing is variable and often undocumented. We present a fully smartphone-based workflow, in which the sample and a color reference are captured simultaneously, enabling image-specific correction. Nile Red-based test strips were measured in a compact PhotoBox with an integrated ColorChecker chart. A color-correction matrix derived individually for each image reduced the mean hue error across the chromatic range of the strips from 5.1 to 1.6°. Using calibrated hue angle as the sole analytical parameter, eight fuels and ethanol–gasoline blends formed largely distinct clusters, with a mean within-fuel scatter of 1.5°. The regulatory-relevant nominal E10 and E20 reference samples were separated by 14.2°. Within the reference dataset, leave-one-strip-out cross-validation correctly assigned 46 of 48 strips (95.8%); both misassignments were from E5 to E10 clusters. Between-batch differences were ≤0.6°, and the inter-device standard deviation for a fixed paper target was 2.0°. Two nominally identical E10 fuels differing in matrix composition deviated by approximately 12°, suggesting that hue reflects effective fuel polarity rather than ethanol content alone. This compact workflow enables reproducible fuel discrimination using a consumer smartphone. A blind validation using unknown samples has yet to be conducted.
- 2 November 2026
- Published by MDPI AG in Preprints.org
Open AccessSmartphone Colorimetry with In-Frame Color Calibration: Hue-Based Discrimination of Diesel-Type Fuels and Ethanol–Gasoline Blends
Color measurements from consumer cameras are difficult to compare because device-specific image processing is variable and often undocumented. We present a fully smartphone-based workflow, in which the sample and a color reference are captured simultaneously, enabling image-specific correction. Nile Red-based test strips were measured in a compact PhotoBox with an integrated ColorChecker chart. A color-correction matrix derived individually for each image reduced the mean hue error across the chromatic range of the strips from 5.1 to 1.6°. Using calibrated hue angle as the sole analytical parameter, eight fuels and ethanol–gasoline blends formed largely distinct clusters, with a mean within-fuel scatter of 1.5°. The regulatory-relevant nominal E10 and E20 reference samples were separated by 14.2°. Within the reference dataset, leave-one-strip-out cross-validation correctly assigned 46 of 48 strips (95.8%); both misassignments were from E5 to E10 clusters. Between-batch differences were ≤0.6°, and the inter-device standard deviation for a fixed paper target was 2.0°. Two nominally identical E10 fuels differing in matrix composition deviated by approximately 12°, suggesting that hue reflects effective fuel polarity rather than ethanol content alone. This compact workflow enables reproducible fuel discrimination using a consumer smartphone. A blind validation using unknown samples has yet to be conducted.
- Open Access
Passive Smart Dust for Detecting and Classifying Fuel Spills: Drone-Based Colorimetric Imaging Using Solvatochromic Paper Sensors
Rapid detection and localization of liquid fuel spills is critical for first responders assessing fire and health hazards, yet current methods require ground-based sampling or specialized instrumentation, limiting their practicality for wide-area emergency response. We present a drone-based passive colorimetric sensor system using test strips impregnated with Nile red, similar to colored confetti. Nile red is a solvatochromic dye that undergoes distinct visible color transitions upon exposure to different liquids. The dye is embedded within a polymer matrix that minimizes leaching while providing high optical contrast between dry, water-exposed, and fuel-exposed states. The sensor strips exhibit solvent-specific colorimetric responses within one minute of exposure, readily detectable by standard RGB cameras mounted on unmanned aerial vehicles (UAVs) at altitudes up to 50 m. Automated classification was validated at 20 m altitude, enabling remote surveillance of contaminated surfaces without specialized equipment. Color-corrected image analysis using Calibrite ColorChecker calibration ensures reliable interpretation under variable field illumination (625–77,000 lux). Systematic laboratory evaluation of twelve fossil and bio-derived fuels revealed characteristic hue shifts that clearly discriminate ethanol-containing gasoline blends from diesel-range fuels. Rather than identifying specific molecules, the method functionally categorizes contamination into gasoline/ethanol blends versus diesel-type fuels, reflecting bulk polarity rather than molecular composition. Field validation confirmed localization and classification of fuel-exposed sensors, achieving F1 scores of 0.94 for gasoline and 0.98 for diesel detection with no false positives in the tested scenarios. This cost-effective and scalable approach provides actionable information on both contamination location and fuel type, crucial for rapid hazard assessment in emergency response scenarios.
Open AccessPassive Smart Dust for Detecting and Classifying Fuel Spills: Drone-Based Colorimetric Imaging Using Solvatochromic Paper Sensors
Rapid detection and localization of liquid fuel spills is critical for first responders assessing fire and health hazards, yet current methods require ground-based sampling or specialized instrumentation, limiting their practicality for wide-area emergency response. We present a drone-based passive colorimetric sensor system using test strips impregnated with Nile red, similar to colored confetti. Nile red is a solvatochromic dye that undergoes distinct visible color transitions upon exposure to different liquids. The dye is embedded within a polymer matrix that minimizes leaching while providing high optical contrast between dry, water-exposed, and fuel-exposed states. The sensor strips exhibit solvent-specific colorimetric responses within one minute of exposure, readily detectable by standard RGB cameras mounted on unmanned aerial vehicles (UAVs) at altitudes up to 50 m. Automated classification was validated at 20 m altitude, enabling remote surveillance of contaminated surfaces without specialized equipment. Color-corrected image analysis using Calibrite ColorChecker calibration ensures reliable interpretation under variable field illumination (625–77,000 lux). Systematic laboratory evaluation of twelve fossil and bio-derived fuels revealed characteristic hue shifts that clearly discriminate ethanol-containing gasoline blends from diesel-range fuels. Rather than identifying specific molecules, the method functionally categorizes contamination into gasoline/ethanol blends versus diesel-type fuels, reflecting bulk polarity rather than molecular composition. Field validation confirmed localization and classification of fuel-exposed sensors, achieving F1 scores of 0.94 for gasoline and 0.98 for diesel detection with no false positives in the tested scenarios. This cost-effective and scalable approach provides actionable information on both contamination location and fuel type, crucial for rapid hazard assessment in emergency response scenarios.
- Open Access
- 8 May 2026
- Published by MDPI AG in Preprints.org
Passive Smart Dust for Detecting and Classifying Fuel Spills: Drone-Based Colorimetric Imaging Using Solvatochromic Paper Sensors
Rapid detection and localization of liquid fuel spills is critical for first responders assessing fire and health hazards, yet current methods require ground-based sampling or specialized instrumentation, limiting their practicality for wide-area emergency response. We present a drone-based passive colorimetric sensor system using test strips impregnated with Nile red, similar to colored confetti. Nile red is a solvatochromic dye that undergoes distinct visible color transitions upon exposure to different liquids. The dye is embedded within a polymer matrix that minimizes leaching while providing high optical contrast between dry, water-exposed, and fuel-exposed states. The sensor strips exhibit solvent-specific colorimetric responses within one minute of exposure, readily detectable by standard RGB cameras mounted on unmanned aerial vehicles (UAV) at altitudes up to 50 m. Automated classification was validated at 20 m altitude, enabling remote surveillance of contaminated surfaces without specialized equipment. Color-corrected image analysis using Calibrite ColorChecker calibration ensures reliable interpretation under variable field illumination (625–77,000 lux). Systematic laboratory evaluation of twelve fossil and bio-derived fuels revealed characteristic hue shifts that clearly discriminate ethanol-containing gasoline blends from diesel-range fuels. Field validation confirmed localization and classification of fuel-exposed sensors, achieving F1 scores of 0.94 for gasoline and 0.98 for diesel detection with no false positives in the tested scenarios. This cost-effective and scalable approach provides actionable information on both contamination location and fuel type, crucial for rapid hazard assessment in emergency response scenarios.
- 8 May 2026
- Published by MDPI AG in Preprints.org
Open AccessPassive Smart Dust for Detecting and Classifying Fuel Spills: Drone-Based Colorimetric Imaging Using Solvatochromic Paper Sensors
Rapid detection and localization of liquid fuel spills is critical for first responders assessing fire and health hazards, yet current methods require ground-based sampling or specialized instrumentation, limiting their practicality for wide-area emergency response. We present a drone-based passive colorimetric sensor system using test strips impregnated with Nile red, similar to colored confetti. Nile red is a solvatochromic dye that undergoes distinct visible color transitions upon exposure to different liquids. The dye is embedded within a polymer matrix that minimizes leaching while providing high optical contrast between dry, water-exposed, and fuel-exposed states. The sensor strips exhibit solvent-specific colorimetric responses within one minute of exposure, readily detectable by standard RGB cameras mounted on unmanned aerial vehicles (UAV) at altitudes up to 50 m. Automated classification was validated at 20 m altitude, enabling remote surveillance of contaminated surfaces without specialized equipment. Color-corrected image analysis using Calibrite ColorChecker calibration ensures reliable interpretation under variable field illumination (625–77,000 lux). Systematic laboratory evaluation of twelve fossil and bio-derived fuels revealed characteristic hue shifts that clearly discriminate ethanol-containing gasoline blends from diesel-range fuels. Field validation confirmed localization and classification of fuel-exposed sensors, achieving F1 scores of 0.94 for gasoline and 0.98 for diesel detection with no false positives in the tested scenarios. This cost-effective and scalable approach provides actionable information on both contamination location and fuel type, crucial for rapid hazard assessment in emergency response scenarios.
- Open Access
- 8 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (22) , 42171-42179
GNN-DM: A Graph Neural Network Framework for Real-World Gas Distribution Mapping
Gas distribution mapping (GDM) is essential for industrial safety and environmental monitoring, as it enables real-time hazard detection and air quality assessment. Traditional GDM methods, such as kernel-based techniques, struggle to reconstruct complex gas plume dynamics accurately. While deep learning has shown promise for GDM, two critical challenges hinder its practical use: the scarcity of available training data and the incompatibility of conventional architectures with irregular sensor layouts. To address these limitations, we propose GNN-DM, a graph neural network-based model for GDM that incorporates the relational structure of sensor networks to infer high-resolution maps from minimal, irregular inputs. The model is pre-trained on synthetic gas dispersion data generated from measured wind data and fine-tuned on two industrial datasets collected on a ferry car deck and in a hot rolling mill. Compared to established GDM techniques, GNN-DM achieves higher accuracy on synthetic and real-world data, highlighting the potential of graph-based learning for practical gas mapping applications.
- 8 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (22) , 42171-42179
Open AccessGNN-DM: A Graph Neural Network Framework for Real-World Gas Distribution Mapping
Gas distribution mapping (GDM) is essential for industrial safety and environmental monitoring, as it enables real-time hazard detection and air quality assessment. Traditional GDM methods, such as kernel-based techniques, struggle to reconstruct complex gas plume dynamics accurately. While deep learning has shown promise for GDM, two critical challenges hinder its practical use: the scarcity of available training data and the incompatibility of conventional architectures with irregular sensor layouts. To address these limitations, we propose GNN-DM, a graph neural network-based model for GDM that incorporates the relational structure of sensor networks to infer high-resolution maps from minimal, irregular inputs. The model is pre-trained on synthetic gas dispersion data generated from measured wind data and fine-tuned on two industrial datasets collected on a ferry car deck and in a hot rolling mill. Compared to established GDM techniques, GNN-DM achieves higher accuracy on synthetic and real-world data, highlighting the potential of graph-based learning for practical gas mapping applications.
- Open Access
Drone-Based Localization of Hazardous Chemicals by Passive Smart Dust
The distribution of tiny sensors over a specific area was first proposed in the late 1990s as a concept known as smart dust. Several efforts focused primarily on computing and networking capabilities, but quickly ran into problems related to power supply, cost, data transmission, and environmental pollution. To overcome these limitations, we propose using paper-based (confetti-like) chemosensors that exploit the inherent selectivity of chemical reagents, such as colorimetric indicators. In this work, cheap and biodegradable passive sensors made from cellulose could successfully indicate the presence of hazardous chemicals, e.g., strong acids, by a significant color change. A conventional color digital camera attached to a drone could easily detect this from a safe distance. The collected data were processed to define the hazardous area. Our work presents a combination of the smart dust concept, chemosensing, paper-based sensor technology, and low-cost drones for flexible, sensitive, economical, and rapid detection of hazardous chemicals in high-risk scenarios.
Open AccessDrone-Based Localization of Hazardous Chemicals by Passive Smart Dust
The distribution of tiny sensors over a specific area was first proposed in the late 1990s as a concept known as smart dust. Several efforts focused primarily on computing and networking capabilities, but quickly ran into problems related to power supply, cost, data transmission, and environmental pollution. To overcome these limitations, we propose using paper-based (confetti-like) chemosensors that exploit the inherent selectivity of chemical reagents, such as colorimetric indicators. In this work, cheap and biodegradable passive sensors made from cellulose could successfully indicate the presence of hazardous chemicals, e.g., strong acids, by a significant color change. A conventional color digital camera attached to a drone could easily detect this from a safe distance. The collected data were processed to define the hazardous area. Our work presents a combination of the smart dust concept, chemosensing, paper-based sensor technology, and low-cost drones for flexible, sensitive, economical, and rapid detection of hazardous chemicals in high-risk scenarios.
- Open Access
- 1 August 2024
- Published by MDPI AG in Preprints.org
Drone-Based Localization of Hazardous Chemicals by Passive Smart Dust
The distribution of tiny sensors over a specific area was first proposed in the late 1990s as a concept known as Smart Dust. Several efforts focused primarily on computing and networking capabilities but quickly ran into problems related to power supply, cost, data transmission, and environmental pollution. To overcome these limitations, we propose using paper-based (confetti-like) chemosensors that exploit the inherent selectivity of chemical reagents, such as colorimetric indicators. In this work, cheap and biodegradable passive sensors made from cellulose could successfully indicate the presence of hazardous chemicals, e.g., strong acids, by a significant color change. A conventional color digital camera attached to a drone could easily detect this from a safe distance. The collected data was processed to define the hazardous area. Our work presents a combination of the smart dust concept, chemosensing, paper-based sensor technology, and low-cost drones for flexible, sensitive, economical, and rapid detection of hazardous chemicals in high-risk scenarios.
- 1 August 2024
- Published by MDPI AG in Preprints.org
Open AccessDrone-Based Localization of Hazardous Chemicals by Passive Smart Dust
The distribution of tiny sensors over a specific area was first proposed in the late 1990s as a concept known as Smart Dust. Several efforts focused primarily on computing and networking capabilities but quickly ran into problems related to power supply, cost, data transmission, and environmental pollution. To overcome these limitations, we propose using paper-based (confetti-like) chemosensors that exploit the inherent selectivity of chemical reagents, such as colorimetric indicators. In this work, cheap and biodegradable passive sensors made from cellulose could successfully indicate the presence of hazardous chemicals, e.g., strong acids, by a significant color change. A conventional color digital camera attached to a drone could easily detect this from a safe distance. The collected data was processed to define the hazardous area. Our work presents a combination of the smart dust concept, chemosensing, paper-based sensor technology, and low-cost drones for flexible, sensitive, economical, and rapid detection of hazardous chemicals in high-risk scenarios.
- Open Access
- 18 July 2024
- Published by Elsevier in Sensors and Actuators B: Chemical
- Vol. 419
Super-resolution for Gas Distribution Mapping
- 18 July 2024
- Published by Elsevier in Sensors and Actuators B: Chemical
- Vol. 419
Open AccessSuper-resolution for Gas Distribution Mapping
- 19 November 2022
- Published by Springer Nature
- p. 105-116
Simulating a Gas Source Localization Algorithm with Gas Dispersion Produced by Recorded Outdoor Wind
- 19 November 2022
- Published by Springer Nature
- p. 105-116
Simulating a Gas Source Localization Algorithm with Gas Dispersion Produced by Recorded Outdoor Wind
- 5 March 2022
- Published by Elsevier in Materials Today: Proceedings
- Vol. 62, 2462-2465
Flying ant robot for chemical trail detection and localization
- 5 March 2022
- Published by Elsevier in Materials Today: Proceedings
- Vol. 62, 2462-2465
Flying ant robot for chemical trail detection and localization
- Open Access
- 13 July 2019
- Published by Taylor & Francis in European Journal of Remote Sensing
- Vol. 52 (sup3) , 2-16
Aerial-based gas tomography – from single beams to complex gas distributions
In this paper, we present and validate the concept of an autonomous aerial robot to reconstruct tomographic 2D slices of gas plumes in outdoor environments. Our platform, the so-called Unmanned Aerial Vehicle for Remote Gas Sensing (UAV-REGAS), combines a lightweight Tunable Diode Laser Absorption Spectroscopy (TDLAS) gas sensor with a 3-axis aerial stabilization gimbal for aiming at a versatile octocopter. While the TDLAS sensor provides integral gas concentration measurements, it does not measure the distance traveled by the laser diode’s beam nor the distribution of gas along the optical path. Thus, we complement the set-up with a laser rangefinder and apply principles of Computed Tomography (CT) to create a model of the spatial gas distribution from a set of integral concentration measurements. To allow for a fundamental ground truth evaluation of the applied gas tomography algorithm, we set up a unique outdoor test environment based on two 3D ultrasonic anemometers and a distributed array of 10 infrared gas transmitters. We present results showing its performance characteristics and 2D plume reconstruction capabilities under realistic conditions. The proposed system can be deployed in scenarios that cannot be addressed by currently available robots and thus constitutes a significant step forward for the field of Mobile Robot Olfaction (MRO).
- 13 July 2019
- Published by Taylor & Francis in European Journal of Remote Sensing
- Vol. 52 (sup3) , 2-16
Open AccessAerial-based gas tomography – from single beams to complex gas distributions
In this paper, we present and validate the concept of an autonomous aerial robot to reconstruct tomographic 2D slices of gas plumes in outdoor environments. Our platform, the so-called Unmanned Aerial Vehicle for Remote Gas Sensing (UAV-REGAS), combines a lightweight Tunable Diode Laser Absorption Spectroscopy (TDLAS) gas sensor with a 3-axis aerial stabilization gimbal for aiming at a versatile octocopter. While the TDLAS sensor provides integral gas concentration measurements, it does not measure the distance traveled by the laser diode’s beam nor the distribution of gas along the optical path. Thus, we complement the set-up with a laser rangefinder and apply principles of Computed Tomography (CT) to create a model of the spatial gas distribution from a set of integral concentration measurements. To allow for a fundamental ground truth evaluation of the applied gas tomography algorithm, we set up a unique outdoor test environment based on two 3D ultrasonic anemometers and a distributed array of 10 infrared gas transmitters. We present results showing its performance characteristics and 2D plume reconstruction capabilities under realistic conditions. The proposed system can be deployed in scenarios that cannot be addressed by currently available robots and thus constitutes a significant step forward for the field of Mobile Robot Olfaction (MRO).