Boris Andreevich Buravov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Boris Andreevich Buravov has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Sergey Vladimirovich Borisov
Volgograd State Technical University
5 shared publications - O. O. Tuzhikov
Volgograd State Technical University
4 shared publications - A. Al-Hamzawi
College of Engineering, Department of Chemical Engineering, University of Al-Qadisiyah, Al-Diwaniyah City, Iraq
3 shared publications - S. M. Solomakhin
Volgograd State Technical University
3 shared publications - Stanislav Albertovich Trubachev
Voevodsky Institute of Chemical Kinetics and Combustion, Siberian Branch of the Russian Academy of Sciences
3 shared publications - Andrey G. Shmakov
Voevodsky Institute of Chemical Kinetics and Combustion SB RAS, Novosibirsk 630090, Russia
2 shared publications
Latest Publications
- 22 May 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (15) , 13876-13890
Carbon‐Fiber Reinforced Plastics With Enhanced Strength Characteristics Based on Electrochemically Modified Carbon Fabrics and Reactive Matrices
Carbon‐fiber‐reinforced plastics with enhanced strength characteristics have been developed based on surface‐modified carbon fabrics and an oligoester methacrylate binder reactive toward them. Under redox initiation conditions, the time to achieve the gel effect ranges from 27.1 to 45.6 min, and the volumetric shrinkage after curing ranges from 2.6% to 4.0%. The surface modification of the carbon fabric was carried out by electrochemical deposition of zinc from a 0.1 M zinc sulfate solution at a current density of 0.1 A/dm 2 . This preserves the fiber integrity while simultaneously achieving the formation of 3–8 μm particles on its surface, containing products of electrochemical oxidation and 11 wt.% Zn. Using the modified fabric and the developed binder, carbon‐fiber‐reinforced plastics were manufactured by the vacuum infusion method. Based on a modified fabric and a developed binder, carbon fiber reinforced plastics were manufactured by vacuum infusion. These composites are characterized by values of elastic modulus, ultimate stress under static bending, and interlaminar shear stress that are, respectively, 77%, 28%, and 62% higher than those of composites made using unmodified fabric.
- 22 May 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (15) , 13876-13890
Carbon‐Fiber Reinforced Plastics With Enhanced Strength Characteristics Based on Electrochemically Modified Carbon Fabrics and Reactive Matrices
Carbon‐fiber‐reinforced plastics with enhanced strength characteristics have been developed based on surface‐modified carbon fabrics and an oligoester methacrylate binder reactive toward them. Under redox initiation conditions, the time to achieve the gel effect ranges from 27.1 to 45.6 min, and the volumetric shrinkage after curing ranges from 2.6% to 4.0%. The surface modification of the carbon fabric was carried out by electrochemical deposition of zinc from a 0.1 M zinc sulfate solution at a current density of 0.1 A/dm 2 . This preserves the fiber integrity while simultaneously achieving the formation of 3–8 μm particles on its surface, containing products of electrochemical oxidation and 11 wt.% Zn. Using the modified fabric and the developed binder, carbon‐fiber‐reinforced plastics were manufactured by the vacuum infusion method. Based on a modified fabric and a developed binder, carbon fiber reinforced plastics were manufactured by vacuum infusion. These composites are characterized by values of elastic modulus, ultimate stress under static bending, and interlaminar shear stress that are, respectively, 77%, 28%, and 62% higher than those of composites made using unmodified fabric.
- 13 May 2026
- Published by Volgograd State Technical University in Izvestia Volgograd State Technical University
- No. 5(312)
POLYMER-OLIGOMERIC MATERIALS WITH INCREASED RESISTANCE TO IMPACT LOADS. PART 2
The modifying effect of secondary polyvinyl chloride on the properties of a cured material based on an epoxy resin was studied. The flexural strength, impact strength and thermal stability of the obtained samples were determined. It was shown that the introduction of secondary polyvinyl chloride leads to an increase in the material's resistance to bending and impact loads, as well as to an improvement in its thermal stability.
- 13 May 2026
- Published by Volgograd State Technical University in Izvestia Volgograd State Technical University
- No. 5(312)
POLYMER-OLIGOMERIC MATERIALS WITH INCREASED RESISTANCE TO IMPACT LOADS. PART 2
The modifying effect of secondary polyvinyl chloride on the properties of a cured material based on an epoxy resin was studied. The flexural strength, impact strength and thermal stability of the obtained samples were determined. It was shown that the introduction of secondary polyvinyl chloride leads to an increase in the material's resistance to bending and impact loads, as well as to an improvement in its thermal stability.
- Open Access
- 14 January 2026
- Published by RTU MIREA in Fine Chemical Technologies
- Vol. 20 (6) , 594-611
Influence of the structure of phosphorus(III)-containing oligoester(meth)acrylates on the physical and mechanical properties, thermal stability, and combustion mechanisms of cured polymers
Objectives. The work sets out to investigate the influence of the structure of spacer in structure of phosphorus(III)-containing oligoester(meth)acrylates on physical and mechanical properties of polymers and their combustibility. Methods. The physical and mechanical properties of polymers were determined using the following: DMA 242 E Artemis dynamic mechanical analyzer ( NETZSCH , Germany); universal testing machine for standard tests on materials ( ZwickRoell Group , Germany); GT-7045-HMH(L) impact test machine ( Gotech Testing Machines, Inc ., Taiwan); Q-1500 D derivatograph of the Paulic–Paulic– Erdey system (thermogravimetry, IOM , Hungary); Oxygen Index Module device for determination of burning behavior by plastic flammability testing according to oxygen index ( Concept Equipment , United Kingdom); GT-7045-HMH(L) device for determination of the Vicat softening temperature ( Gotech Testing Machines, Inc ., Taiwan); SFT-110XW supercritical fluid extractor ( Supercritical Fluid Technologies, Inc ., USA) for supercritical fluid extraction with carbon dioxide. Results. The influence of the spacer structure in the structure of phosphorus(III)-containing oligoester(meth)acrylates on the dynamic mechanical and physicomechanical properties of polymers was established. Comparative assessment of the impact of the spacer structure on properties of polymers was carried out in terms of their heat stability (thermogravimetric analysis) and combustibility (measurement of limited oxygen index). It is established that polymers having balanced physical and mechanical properties can be obtained by introducing spacer characteristics into the oligomer structure. Polymers obtained on the basis of phosphorus(III)-containing oligoester(meth)acrylates with spacers demonstrate considerable resistance to impact strength tests. Conclusions. The achieved results testify to the possibility of obtaining polymers on the basis of phosphorus(III)-containing oligoester(meth)acrylates with spacer attributes that possess increased resistance to impact strength and thermal stability tests at an insignificant decrease in their combustibility.
- 14 January 2026
- Published by RTU MIREA in Fine Chemical Technologies
- Vol. 20 (6) , 594-611
Open AccessInfluence of the structure of phosphorus(III)-containing oligoester(meth)acrylates on the physical and mechanical properties, thermal stability, and combustion mechanisms of cured polymers
Objectives. The work sets out to investigate the influence of the structure of spacer in structure of phosphorus(III)-containing oligoester(meth)acrylates on physical and mechanical properties of polymers and their combustibility. Methods. The physical and mechanical properties of polymers were determined using the following: DMA 242 E Artemis dynamic mechanical analyzer ( NETZSCH , Germany); universal testing machine for standard tests on materials ( ZwickRoell Group , Germany); GT-7045-HMH(L) impact test machine ( Gotech Testing Machines, Inc ., Taiwan); Q-1500 D derivatograph of the Paulic–Paulic– Erdey system (thermogravimetry, IOM , Hungary); Oxygen Index Module device for determination of burning behavior by plastic flammability testing according to oxygen index ( Concept Equipment , United Kingdom); GT-7045-HMH(L) device for determination of the Vicat softening temperature ( Gotech Testing Machines, Inc ., Taiwan); SFT-110XW supercritical fluid extractor ( Supercritical Fluid Technologies, Inc ., USA) for supercritical fluid extraction with carbon dioxide. Results. The influence of the spacer structure in the structure of phosphorus(III)-containing oligoester(meth)acrylates on the dynamic mechanical and physicomechanical properties of polymers was established. Comparative assessment of the impact of the spacer structure on properties of polymers was carried out in terms of their heat stability (thermogravimetric analysis) and combustibility (measurement of limited oxygen index). It is established that polymers having balanced physical and mechanical properties can be obtained by introducing spacer characteristics into the oligomer structure. Polymers obtained on the basis of phosphorus(III)-containing oligoester(meth)acrylates with spacers demonstrate considerable resistance to impact strength tests. Conclusions. The achieved results testify to the possibility of obtaining polymers on the basis of phosphorus(III)-containing oligoester(meth)acrylates with spacer attributes that possess increased resistance to impact strength and thermal stability tests at an insignificant decrease in their combustibility.
- Open Access
Low-Flammability Hybrid Polymer Materials Based on Epoxy Oligomers and In Situ-Synthesized Zinc-Containing Microparticles
This study addresses the drawbacks of traditional dispersed fire retardants—such as anisotropy, reduced strength, and poor filler impregnability—by developing in situ-formed hybrid epoxy composites. The materials, based on diglycidyl ether of bisphenol A and triethylenetetramine, were modified with a solution of zinc sulfate heptahydrate in orthophosphoric acid. This approach yielded near-spherical microparticles (6–16 µm) within the polymer matrix. The scientific novelty lies in investigating how such in situ particle formation affects material properties. The modification significantly enhanced fire resistance: char residue increased 1.7–2.2-fold, while total heat release, peak heat release rate, and smoke release were reduced by up to 60.5%, 40.2%, and 70%, respectively. The observed increase in the mass loss rate suggests that accelerated thermal-oxidative degradation promotes char formation. These findings, supported by scanning electron microscopy, energy-dispersive X-ray spectroscopy, and Fourier-transform infrared spectroscopy data, demonstrate the efficacy of the in situ strategy for creating high-performance, fire-safe epoxy composites.
Open AccessLow-Flammability Hybrid Polymer Materials Based on Epoxy Oligomers and In Situ-Synthesized Zinc-Containing Microparticles
This study addresses the drawbacks of traditional dispersed fire retardants—such as anisotropy, reduced strength, and poor filler impregnability—by developing in situ-formed hybrid epoxy composites. The materials, based on diglycidyl ether of bisphenol A and triethylenetetramine, were modified with a solution of zinc sulfate heptahydrate in orthophosphoric acid. This approach yielded near-spherical microparticles (6–16 µm) within the polymer matrix. The scientific novelty lies in investigating how such in situ particle formation affects material properties. The modification significantly enhanced fire resistance: char residue increased 1.7–2.2-fold, while total heat release, peak heat release rate, and smoke release were reduced by up to 60.5%, 40.2%, and 70%, respectively. The observed increase in the mass loss rate suggests that accelerated thermal-oxidative degradation promotes char formation. These findings, supported by scanning electron microscopy, energy-dispersive X-ray spectroscopy, and Fourier-transform infrared spectroscopy data, demonstrate the efficacy of the in situ strategy for creating high-performance, fire-safe epoxy composites.
- Open Access
- 4 November 2024
- Published by RTU MIREA in Fine Chemical Technologies
- Vol. 19 (5) , 441-451
Rheological properties of phosphorus-containing oligoester(meth)acrylate for processing by vacuum infusion
Objectives. To obtain polymer composite materials (PCM) with enhanced physicomechanical properties using the vacuum assisted resin transfer molding (VaRTM) method, binders must have a viscosity of up to 500 mPa∙s. In some cases, this leads to restrictions on the use of certain materials or requires the use of temporary diluents. This is closely related to the deterioration of other required composite characteristics, such as increased flammability. Three phosphorus-containing oligoester(meth)acrylates PhOEM-1, PhOEM-2, and PhOEM-3 were synthesized with significant differences in viscosity characteristics in the series PhOEM-1 << PhOEM-2 << PhOEM-3. The polymer based on PhOEM-1 exhibits inferior physicomechanical properties despite having lower viscosity. Hence, the aim of the study was to investigate the viscosity characteristics of mixtures of methacrylate binders of the same nature but different structures and functionalities. This was done by studying the rheological properties of the original oligoester(meth)acrylates and their mixtures taken in various ratios. The method used was to optimize compositions via a simplex lattice (Scheffe’s plan), in order to obtain PCM using the VaRTM technology.Methods. The study of rheological properties of phosphorus-containing oligoester(meth)acrylates and their mixtures was conducted using the method of rotational viscometry on a Brookfield LVDV-II + Pro viscometer with a spindle 27 at different shear rates ranging from 0 to 70 s−1 and temperatures from 30 to 70°C. Rheological studies were also conducted on a Lamy Rheology GT300 PLUS (GEL TIMER) viscometer in the same range of shear rates and temperatures.Results. It was established that the objects under investigation can be characterized by viscosity values ranging from 96 to 2137 mPa∙s depending on the temperature. The nature of the viscous flow of phosphorus-containing oligoester(meth)acrylates and their mixtures is similar to that of Newtonian liquids only at certain shear rates. The effective activation energies of the viscous flow of binders and their mixtures were calculated, and the influence of temperature on the viscosity of binders was determined.Conclusions. The study identified the features and nature of the flow curves of phosphorus-containing oligoester(meth)acrylate binders of the same nature but different structures and functionalities, as well as of their mixtures. The optimal composition ranges of threecomponent mixtures of phosphorus-containing oligoester(meth)acrylates for use in the VaRTM technological process in producing polymer composite materials within the temperature range of 30 to 70°C were defined. The optimal compositions and temperature conditions for obtaining polymer composite materials using the VaRTM technology were also identified. This enables the production of polymer products with complex geometric shapes and varying sizes.
- 4 November 2024
- Published by RTU MIREA in Fine Chemical Technologies
- Vol. 19 (5) , 441-451
Open AccessRheological properties of phosphorus-containing oligoester(meth)acrylate for processing by vacuum infusion
Objectives. To obtain polymer composite materials (PCM) with enhanced physicomechanical properties using the vacuum assisted resin transfer molding (VaRTM) method, binders must have a viscosity of up to 500 mPa∙s. In some cases, this leads to restrictions on the use of certain materials or requires the use of temporary diluents. This is closely related to the deterioration of other required composite characteristics, such as increased flammability. Three phosphorus-containing oligoester(meth)acrylates PhOEM-1, PhOEM-2, and PhOEM-3 were synthesized with significant differences in viscosity characteristics in the series PhOEM-1 << PhOEM-2 << PhOEM-3. The polymer based on PhOEM-1 exhibits inferior physicomechanical properties despite having lower viscosity. Hence, the aim of the study was to investigate the viscosity characteristics of mixtures of methacrylate binders of the same nature but different structures and functionalities. This was done by studying the rheological properties of the original oligoester(meth)acrylates and their mixtures taken in various ratios. The method used was to optimize compositions via a simplex lattice (Scheffe’s plan), in order to obtain PCM using the VaRTM technology.Methods. The study of rheological properties of phosphorus-containing oligoester(meth)acrylates and their mixtures was conducted using the method of rotational viscometry on a Brookfield LVDV-II + Pro viscometer with a spindle 27 at different shear rates ranging from 0 to 70 s−1 and temperatures from 30 to 70°C. Rheological studies were also conducted on a Lamy Rheology GT300 PLUS (GEL TIMER) viscometer in the same range of shear rates and temperatures.Results. It was established that the objects under investigation can be characterized by viscosity values ranging from 96 to 2137 mPa∙s depending on the temperature. The nature of the viscous flow of phosphorus-containing oligoester(meth)acrylates and their mixtures is similar to that of Newtonian liquids only at certain shear rates. The effective activation energies of the viscous flow of binders and their mixtures were calculated, and the influence of temperature on the viscosity of binders was determined.Conclusions. The study identified the features and nature of the flow curves of phosphorus-containing oligoester(meth)acrylate binders of the same nature but different structures and functionalities, as well as of their mixtures. The optimal composition ranges of threecomponent mixtures of phosphorus-containing oligoester(meth)acrylates for use in the VaRTM technological process in producing polymer composite materials within the temperature range of 30 to 70°C were defined. The optimal compositions and temperature conditions for obtaining polymer composite materials using the VaRTM technology were also identified. This enables the production of polymer products with complex geometric shapes and varying sizes.
- Open Access
Flame-Retardant Glass Fiber-Reinforced Epoxy Resins with Phosphorus-Containing Bio-Based Benzoxazines and Graphene
This paper presents a study of the flammability and thermal decomposition products of glass fiber-reinforced epoxy resin (GFRER) with the addition of cardanol-based phosphorus-containing benzoxazine monomer (CBz) and graphene and their combinations in different proportions (up to 20 wt.%). The addition of CBz alone or in combination with graphene resulted in an increase in the limiting oxygen index (LOI) and self-extinguishing in the UL-94 HB test. The flame-retardant samples had better tensile mechanical properties than the sample without additives. The differential mass-spectrometric thermal analysis (DMSTA) of the thermal decomposition products of GFRER without additives and with the addition of CBz and graphene was carried out. CBz addition promoted the thermal decomposition of high-molecular-weight products of epoxy resin decomposition in the condensed phase and at the same time decreased the time of release of low-molecular-weight thermal decomposition products into the gas phase. Graphene addition resulted in an increase in the relative intensities of high-molecular-mass peaks compared to GFRER without additives.
Open AccessFlame-Retardant Glass Fiber-Reinforced Epoxy Resins with Phosphorus-Containing Bio-Based Benzoxazines and Graphene
This paper presents a study of the flammability and thermal decomposition products of glass fiber-reinforced epoxy resin (GFRER) with the addition of cardanol-based phosphorus-containing benzoxazine monomer (CBz) and graphene and their combinations in different proportions (up to 20 wt.%). The addition of CBz alone or in combination with graphene resulted in an increase in the limiting oxygen index (LOI) and self-extinguishing in the UL-94 HB test. The flame-retardant samples had better tensile mechanical properties than the sample without additives. The differential mass-spectrometric thermal analysis (DMSTA) of the thermal decomposition products of GFRER without additives and with the addition of CBz and graphene was carried out. CBz addition promoted the thermal decomposition of high-molecular-weight products of epoxy resin decomposition in the condensed phase and at the same time decreased the time of release of low-molecular-weight thermal decomposition products into the gas phase. Graphene addition resulted in an increase in the relative intensities of high-molecular-mass peaks compared to GFRER without additives.
- Open Access
- 20 November 2022
- Published by RTU MIREA in Fine Chemical Technologies
- Vol. 17 (5) , 410-426
Synthesis of new photo-cured phosphorus-containing oligoestermethacrylates with a spacer in the structure
Objectives. To synthesize phosphorus-containing oligoestermethacrylates spatially separated by spacers of aliphatic or aromatic structure and evaluate their effect on photocuring kinetics.Methods. For determining the qualitative and quantitative composition of the synthesized compounds, the following methods were used: thin layer chromatography; chromatographic and mass spectrometry; infrared spectroscopy; 1H, 13C, 31P nuclear magnetic resonance spectroscopy; differential scanning calorimetry. The dielectric loss tangent was determined on a specially designed optical cell with an ultraviolet (UV) light source to an immittance meter. Elemental analysis was performed on an energy dispersive X-ray fluorescence spectrometer.Results. Spatially separated oligoestermethacrylates based on phosphorus trichloride containing aliphatic or aromatic spacers in the structure were synthesized. During the interaction of glycidyl methacrylate with phosphorus trichloride in the mass of the latter, reaction products were shown to be formed both according to the Krasusky rule from the side of the α-carbon atom, as well as against this rule with the formation of isomeric products. Obtaining these compounds in bulk is possible only in the presence of a homopolymerization inhibitor. The influence of the spacer structure on the curing rate of oligoestermethacrylates under the action of UV radiation has been established. It has been shown that the introduction of a spacer into the oligomer structure is accompanied by an increase in the induction period by a factor of 39 compared to a sample without a spacer.Conclusions. The results obtained indicate the possibility of obtaining new oligoestermethacrylates with aliphatic and aromatic spacers in the structure. The influence of the structure of the spacer on the kinetics of photocuring is determined.
- 20 November 2022
- Published by RTU MIREA in Fine Chemical Technologies
- Vol. 17 (5) , 410-426
Open AccessSynthesis of new photo-cured phosphorus-containing oligoestermethacrylates with a spacer in the structure
Objectives. To synthesize phosphorus-containing oligoestermethacrylates spatially separated by spacers of aliphatic or aromatic structure and evaluate their effect on photocuring kinetics.Methods. For determining the qualitative and quantitative composition of the synthesized compounds, the following methods were used: thin layer chromatography; chromatographic and mass spectrometry; infrared spectroscopy; 1H, 13C, 31P nuclear magnetic resonance spectroscopy; differential scanning calorimetry. The dielectric loss tangent was determined on a specially designed optical cell with an ultraviolet (UV) light source to an immittance meter. Elemental analysis was performed on an energy dispersive X-ray fluorescence spectrometer.Results. Spatially separated oligoestermethacrylates based on phosphorus trichloride containing aliphatic or aromatic spacers in the structure were synthesized. During the interaction of glycidyl methacrylate with phosphorus trichloride in the mass of the latter, reaction products were shown to be formed both according to the Krasusky rule from the side of the α-carbon atom, as well as against this rule with the formation of isomeric products. Obtaining these compounds in bulk is possible only in the presence of a homopolymerization inhibitor. The influence of the spacer structure on the curing rate of oligoestermethacrylates under the action of UV radiation has been established. It has been shown that the introduction of a spacer into the oligomer structure is accompanied by an increase in the induction period by a factor of 39 compared to a sample without a spacer.Conclusions. The results obtained indicate the possibility of obtaining new oligoestermethacrylates with aliphatic and aromatic spacers in the structure. The influence of the structure of the spacer on the kinetics of photocuring is determined.