Jiangbo Huo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jiangbo Huo has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Guoce Yu
Laboratory of Environmental Technology, INET, Tsinghua University, Beijing 100084, China
2 shared publications - Qing Du
Joint Research Centre for Protective Infrastructure Technology and Environmental Green Bioprocess, School of Environmental and Municipal Engineering, Tianjin Chengjian University, Tianjin 300384, China
1 shared publication - Shunwei Ma
Tianjin College, University of Science and Technology Beijing, Tianjin 301830, China
1 shared publication - Xinbo Zhang
Joint Research Centre for Protective Infrastructure Technology and Environmental Green Bioprocess, School of Environmental and Municipal Engineering, Tianjin Chengjian University, Tianjin 300384, China; Tianjin Key Laboratory of Aquatic Science and Technology, Tianjin Chengjian University, Jinjing Road 26, Tianjin 300384, China
1 shared publication - Xinran Xie
Laboratory of Environmental Technology, INET, Tsinghua University, Beijing 100084, China
1 shared publication - Xuefei Wang
Tianjin College, University of Science and Technology Beijing, Tianjin 301830, China
1 shared publication
Latest Publications
- Open Access
- 27 December 2024
- Published by MDPI AG in Clean Technologies
- Vol. 7 (1) , 2
Nitrogen-Doped Calcite Derived from Ca-MOFs as an Efficient Adsorbent for Sr(II) Removal from Water: The Role of Nitrogen and Calcium
Strontium (90Sr) is a typical radionuclide, which can act as a contaminant and poses a big problem for the eco-environment if left untreated. In this study, an original nitrogen-doped calcite (N-CaCO3) was synthesized using a solvothermal and calcination method and used to remove Sr(II) from simulated water. XRD, SEM, and XPS analyses proved that N was successfully doped into CaCO3, resulting in porous CaCO3 with a regular morphology. The specific surface area of N-CaCO3 (136.53 m2/g) can reach 2.19-fold greater than that of CaCO3. The results based on the batch adsorption data indicated that the pseudo-second-order kinetic model (R2 = 0.9964) and the ion exchange model (R2 = 0.9859) fitted the adsorption data well. The as-synthesized N-CaCO3 exhibited better adsorption performance in regard to low concentrations of Sr(II) (below 64.5 mg/L) compared with commercial CaCO3. The structural analysis suggested that Ca and N played pivotal roles in the adsorption process and that the adsorption mechanism was dominated by ion exchange and surface complexation. This study successfully fabricated a nitrogen-doped calcite for Sr(II) cleanup, presenting an efficient strategy to modulate the microstructure of CaCO3, or other materials, to enhance its adsorption performance.
- 27 December 2024
- Published by MDPI AG in Clean Technologies
- Vol. 7 (1) , 2
Open AccessNitrogen-Doped Calcite Derived from Ca-MOFs as an Efficient Adsorbent for Sr(II) Removal from Water: The Role of Nitrogen and Calcium
Strontium (90Sr) is a typical radionuclide, which can act as a contaminant and poses a big problem for the eco-environment if left untreated. In this study, an original nitrogen-doped calcite (N-CaCO3) was synthesized using a solvothermal and calcination method and used to remove Sr(II) from simulated water. XRD, SEM, and XPS analyses proved that N was successfully doped into CaCO3, resulting in porous CaCO3 with a regular morphology. The specific surface area of N-CaCO3 (136.53 m2/g) can reach 2.19-fold greater than that of CaCO3. The results based on the batch adsorption data indicated that the pseudo-second-order kinetic model (R2 = 0.9964) and the ion exchange model (R2 = 0.9859) fitted the adsorption data well. The as-synthesized N-CaCO3 exhibited better adsorption performance in regard to low concentrations of Sr(II) (below 64.5 mg/L) compared with commercial CaCO3. The structural analysis suggested that Ca and N played pivotal roles in the adsorption process and that the adsorption mechanism was dominated by ion exchange and surface complexation. This study successfully fabricated a nitrogen-doped calcite for Sr(II) cleanup, presenting an efficient strategy to modulate the microstructure of CaCO3, or other materials, to enhance its adsorption performance.
- Open Access
- 17 November 2024
- Published by MDPI AG in Nanomaterials
- Vol. 14 (22) , 1838
Potassium-Based Solid Sorbents for CO2 Adsorption: Key Role of Interconnected Pores
Industrial CO2 emissions contribute to pollution and greenhouse effects, highlighting the importance of carbon capture. Potassium carbonate (K2CO3) is an effective CO2 absorbent, yet its liquid-phase absorption faces issues like diffusion resistance and corrosion risks. In this work, the solid adsorbents were developed with K2CO3 immobilized on the selected porous supports. Al2O3 had an optimum CO2 adsorption capacity of 0.82 mmol g−1. After further optimization of its pore structure, the self-prepared support Al2O3-2, which has an average pore diameter of 11.89 nm and a pore volume of 0.59 cm3 g−1, achieved a maximum CO2 adsorption capacity of 1.12 mmol g−1 following K2CO3 impregnation. Additionally, the relationship between support structure and CO2 adsorption efficiency was also analyzed. The connectivity of the pores and the large pore diameter of the support may play a key role in enhancing CO2 adsorption performance. During 10 cycles of testing, the K2CO3-based adsorbents demonstrated consistent high CO2 adsorption capacity with negligible degradation.
- 17 November 2024
- Published by MDPI AG in Nanomaterials
- Vol. 14 (22) , 1838
Open AccessPotassium-Based Solid Sorbents for CO2 Adsorption: Key Role of Interconnected Pores
Industrial CO2 emissions contribute to pollution and greenhouse effects, highlighting the importance of carbon capture. Potassium carbonate (K2CO3) is an effective CO2 absorbent, yet its liquid-phase absorption faces issues like diffusion resistance and corrosion risks. In this work, the solid adsorbents were developed with K2CO3 immobilized on the selected porous supports. Al2O3 had an optimum CO2 adsorption capacity of 0.82 mmol g−1. After further optimization of its pore structure, the self-prepared support Al2O3-2, which has an average pore diameter of 11.89 nm and a pore volume of 0.59 cm3 g−1, achieved a maximum CO2 adsorption capacity of 1.12 mmol g−1 following K2CO3 impregnation. Additionally, the relationship between support structure and CO2 adsorption efficiency was also analyzed. The connectivity of the pores and the large pore diameter of the support may play a key role in enhancing CO2 adsorption performance. During 10 cycles of testing, the K2CO3-based adsorbents demonstrated consistent high CO2 adsorption capacity with negligible degradation.
- Open Access
- 22 November 2022
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 23 (23) , 14556
Layered Double Hydroxides Derived from MIL-88A(Fe) as an Efficient Adsorbent for Enhanced Removal of Lead (II) from Water
The efficient removal of lead (II) from aqueous solution remains a big problem and the development of novel nanomaterials as adsorbents by various technologies to solve this problem is promising. This study contributed a novel nanostructure of MIL-88A-layered double hydroxides (LDHs) as the adsorbent for Pb2+, which was synthesized by a two-step solvothermal method with MIL-88A(Fe) as the precursor. The as-prepared material featured a chestnut-like core-shell structure, and exhibited excellent removal performance towards Pb2+ from water in comparison to MIL-88A(Fe) and LDHs (directly synthesized). The adsorption of Pb2+ by the MIL-88A-LDHs conformed to the pseudo-second-order kinetic model and the Langmuir and Freundlich isotherm models. The maximal adsorption capacity was 526.32, 625.00, and 909.09 mg g−1 at 278, 298, and 318 K, respectively. The thermodynamic parameters suggested that the adsorption was an endothermic, entropy-increasing, and spontaneous reaction. X-ray photoelectron spectroscopy (XPS) analysis indicated that the surface complexation was mostly responsible for Pb2+ elimination. The MIL-88A-LDHs can be readily regenerated and showed good cyclic performance towards Pb2+. Thus, the as-prepared MIL-88A-LDHs may hold promise for the elimination of aqueous heavy metals.
- 22 November 2022
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 23 (23) , 14556
Open AccessLayered Double Hydroxides Derived from MIL-88A(Fe) as an Efficient Adsorbent for Enhanced Removal of Lead (II) from Water
The efficient removal of lead (II) from aqueous solution remains a big problem and the development of novel nanomaterials as adsorbents by various technologies to solve this problem is promising. This study contributed a novel nanostructure of MIL-88A-layered double hydroxides (LDHs) as the adsorbent for Pb2+, which was synthesized by a two-step solvothermal method with MIL-88A(Fe) as the precursor. The as-prepared material featured a chestnut-like core-shell structure, and exhibited excellent removal performance towards Pb2+ from water in comparison to MIL-88A(Fe) and LDHs (directly synthesized). The adsorption of Pb2+ by the MIL-88A-LDHs conformed to the pseudo-second-order kinetic model and the Langmuir and Freundlich isotherm models. The maximal adsorption capacity was 526.32, 625.00, and 909.09 mg g−1 at 278, 298, and 318 K, respectively. The thermodynamic parameters suggested that the adsorption was an endothermic, entropy-increasing, and spontaneous reaction. X-ray photoelectron spectroscopy (XPS) analysis indicated that the surface complexation was mostly responsible for Pb2+ elimination. The MIL-88A-LDHs can be readily regenerated and showed good cyclic performance towards Pb2+. Thus, the as-prepared MIL-88A-LDHs may hold promise for the elimination of aqueous heavy metals.