Hojin Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hojin Kim has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Chung-Hyun Lee
Department of Energy and Mineral Resources Engineering, Kangwon National University, Samcheok 25913, Republic of Korea
2 shared publications - Sung-Min Kim
Department of Energy Resources and Chemical Engineering Kangwon National University Samcheok Korea
2 shared publications - Woo-Hyuk Lee
Department of Energy and Mineral Resources Engineering, Kangwon National University, Samcheok 25913, Republic of Korea
2 shared publications
Latest Publications
- Open Access
- 28 November 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (23) , 12166
Development of Monitoring Technology for Mine Haulage Road through Sensor-Connected Digital Device and Smartphone Application
A system that can acquire and share information about the environment from vehicles using various sensors and smartphones was developed to prevent accidents that may occur on mine haulage roads. A light detection and ranging sensor and an accelerometer in a smartphone were used to determine the road surface conditions at a mining site, and dust and gas sensors were used to measure the atmospheric environment. The GPS function of the smartphone was utilized to obtain the location data of the vehicle, and a smartphone application was developed to collect and share this information. A preliminary test was conducted at Samcheok Campus, Kangwon National University, and a field test at the Samdo mine. The data acquired from each vehicle could be shared in real time. Additionally, by analyzing the spatial distribution of each dataset, sections with rough road surfaces and those with poor atmospheric conditions could be identified. If the technology is further developed and big-data analysis is performed in the future, the developed technology could contribute to improving the mining environment.
- 28 November 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (23) , 12166
Open AccessDevelopment of Monitoring Technology for Mine Haulage Road through Sensor-Connected Digital Device and Smartphone Application
A system that can acquire and share information about the environment from vehicles using various sensors and smartphones was developed to prevent accidents that may occur on mine haulage roads. A light detection and ranging sensor and an accelerometer in a smartphone were used to determine the road surface conditions at a mining site, and dust and gas sensors were used to measure the atmospheric environment. The GPS function of the smartphone was utilized to obtain the location data of the vehicle, and a smartphone application was developed to collect and share this information. A preliminary test was conducted at Samcheok Campus, Kangwon National University, and a field test at the Samdo mine. The data acquired from each vehicle could be shared in real time. Additionally, by analyzing the spatial distribution of each dataset, sections with rough road surfaces and those with poor atmospheric conditions could be identified. If the technology is further developed and big-data analysis is performed in the future, the developed technology could contribute to improving the mining environment.
- Open Access
- 23 November 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (23) , 11927
Development of Digital Device Using ZigBee for Environmental Monitoring in Underground Mines
In underground mines, various mining activities may generate dust or vibrations, affecting workers’ health and safety. Therefore, for worker safety, we must monitor the environment and identify possible risks. However, it is difficult to install multiple sensors and acquire data simultaneously because of the difficulties of connecting to an external network in underground mines. This study developed a digital device to share acquired data by combining ZigBee communication technology with an accelerometer and dust sensor. In total, 29 vibration modules, 14 dust modules, and 2 coordinator modules were installed at Taeyoung EMC’s Samdo Mine in Samcheok, Republic of Korea. Because of its application, we could detect changes in vibration and dust before and after blasting. The dust density of the devices close to the blasting point increases rapidly up to about 230 µg/m3 and then decreases to about 180 µg/m3, and the dust density of the devices further increases over time. The dust density was usually maintained at a value of about 100 to 150 µg/m3 before blasting. The spatial distribution of the dust density of multiple devices was visualized using ArcGIS Pro. Although the wireless sensor network is well-established, some modules were temporarily disconnected from the network. In order to solve the problem of unstable network connection in some modules, change of network settings and line of sight analysis are required. Improvements in the technology developed in this study may help prevent potential hazards in underground mines.
- 23 November 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (23) , 11927
Open AccessDevelopment of Digital Device Using ZigBee for Environmental Monitoring in Underground Mines
In underground mines, various mining activities may generate dust or vibrations, affecting workers’ health and safety. Therefore, for worker safety, we must monitor the environment and identify possible risks. However, it is difficult to install multiple sensors and acquire data simultaneously because of the difficulties of connecting to an external network in underground mines. This study developed a digital device to share acquired data by combining ZigBee communication technology with an accelerometer and dust sensor. In total, 29 vibration modules, 14 dust modules, and 2 coordinator modules were installed at Taeyoung EMC’s Samdo Mine in Samcheok, Republic of Korea. Because of its application, we could detect changes in vibration and dust before and after blasting. The dust density of the devices close to the blasting point increases rapidly up to about 230 µg/m3 and then decreases to about 180 µg/m3, and the dust density of the devices further increases over time. The dust density was usually maintained at a value of about 100 to 150 µg/m3 before blasting. The spatial distribution of the dust density of multiple devices was visualized using ArcGIS Pro. Although the wireless sensor network is well-established, some modules were temporarily disconnected from the network. In order to solve the problem of unstable network connection in some modules, change of network settings and line of sight analysis are required. Improvements in the technology developed in this study may help prevent potential hazards in underground mines.