Zachary R. Brumbach
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zachary R. Brumbach has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Jeffrey W. Teng
The Aerospace Corporation, El Segundo, CA, USA
12 shared publications - John D. Cressler
Georgia Institute of Technology
12 shared publications - Adrian Ildefonso
U.S. Naval Research Laboratory, Washington, DC, USA
9 shared publications - Ani Khachatrian
U.S. Naval Research Laboratory, Washington, DC, USA
9 shared publications - Brett L. Ringel
Georgia Institute of Technology
9 shared publications - Dale McMorrow
U.S. Naval Research Laboratory, Washington, DC, USA
7 shared publications
Latest Publications
- 12 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. PP (00189499) , 1
Analysis of Optical and Electrical Single-Event Transients in Integrated Silicon Photonic Micro-Ring Modulators
The single-event-effect (SEE) responses of microring modulators (MRMs) are evaluated. Charge was introduced using a pulsed-laser system capable of locally injecting electron-hole pairs (EHPs) via two-photon absorption (TPA). Both electrical single-event transients (SETs) and optical single-event transients (OSETs) were collected for different input wavelengths, anode biases, and laser pulse energies (PEs). Laser-equivalent linear energy transfer (LETL) threshold sensitivity, SET amplitude, and SET duration, were found to be highly dependent on the operational bias. Wavelengths in and around resonance conditions, typically heavily used operating conditions for MRM applications, exhibit the highest OSET sensitivity. Reasons for, and implications of, these bias dependencies are analyzed through free-carrier-plasma-dispersion (FCPD) theory and literature on pump-probe experiments in photonic ring structures. Analysis supports transients occur due to changes in the refractive index incurred during carrier injection, as well as thermal generation from free-carrier absorption (FCA). OSETs are observed down to a minimum PE = 207 pJ, corresponding to an LETL of 5.2 MeV • cm2• mg−1, relevant for space environments and orbital applications. Contrary to existing literature claims, the theory, data, and analysis presented in this work suggest that not all photonic components are SEE-resilient, with MRMs exhibiting the highest OSET sensitivity of any photonic component reported to date.
- 12 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. PP (00189499) , 1
Analysis of Optical and Electrical Single-Event Transients in Integrated Silicon Photonic Micro-Ring Modulators
The single-event-effect (SEE) responses of microring modulators (MRMs) are evaluated. Charge was introduced using a pulsed-laser system capable of locally injecting electron-hole pairs (EHPs) via two-photon absorption (TPA). Both electrical single-event transients (SETs) and optical single-event transients (OSETs) were collected for different input wavelengths, anode biases, and laser pulse energies (PEs). Laser-equivalent linear energy transfer (LETL) threshold sensitivity, SET amplitude, and SET duration, were found to be highly dependent on the operational bias. Wavelengths in and around resonance conditions, typically heavily used operating conditions for MRM applications, exhibit the highest OSET sensitivity. Reasons for, and implications of, these bias dependencies are analyzed through free-carrier-plasma-dispersion (FCPD) theory and literature on pump-probe experiments in photonic ring structures. Analysis supports transients occur due to changes in the refractive index incurred during carrier injection, as well as thermal generation from free-carrier absorption (FCA). OSETs are observed down to a minimum PE = 207 pJ, corresponding to an LETL of 5.2 MeV • cm2• mg−1, relevant for space environments and orbital applications. Contrary to existing literature claims, the theory, data, and analysis presented in this work suggest that not all photonic components are SEE-resilient, with MRMs exhibiting the highest OSET sensitivity of any photonic component reported to date.
- 18 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 73 (1) , 138-146
Impact of Total-Ionizing Dose on Injection-Locked Voltage-Controlled Oscillators
Voltage-controlled oscillators (VCOs) are key components in providing periodic signals that are used in RF communications systems for time synchronization and signal processing. However, standalone VCOs can have poor phase noise performance and experience frequency drift; therefore, injection locking can be implemented in a VCO to stabilize these performance metrics. Injection-locked VCOs (ILVCOs) in satellite communications or radar systems can be subject to total-ionizing dose (TID) effects, which could alter the performance of the oscillator. The present work analyzes the effects of TID in a 5 GHz ILVCO using an X-ray source, and demonstrates that the locking range increases and phase noise of the ILVCO improves with total dose. This unexpected result was analyzed using circuit simulations and shows that the negative threshold voltage shifts induced by TID may be posited to the increase of the ratio of injection signal current to oscillator signal current, which may ultimately extend the locking range. Consequently, the increase in the strength of the injection signal due to TID may also lead to the decrease of phase noise. These results suggest that the use of ILVCOs in satellite systems may be favorable as they are TID radiation tolerant compared to standalone oscillators.
- 18 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 73 (1) , 138-146
Impact of Total-Ionizing Dose on Injection-Locked Voltage-Controlled Oscillators
Voltage-controlled oscillators (VCOs) are key components in providing periodic signals that are used in RF communications systems for time synchronization and signal processing. However, standalone VCOs can have poor phase noise performance and experience frequency drift; therefore, injection locking can be implemented in a VCO to stabilize these performance metrics. Injection-locked VCOs (ILVCOs) in satellite communications or radar systems can be subject to total-ionizing dose (TID) effects, which could alter the performance of the oscillator. The present work analyzes the effects of TID in a 5 GHz ILVCO using an X-ray source, and demonstrates that the locking range increases and phase noise of the ILVCO improves with total dose. This unexpected result was analyzed using circuit simulations and shows that the negative threshold voltage shifts induced by TID may be posited to the increase of the ratio of injection signal current to oscillator signal current, which may ultimately extend the locking range. Consequently, the increase in the strength of the injection signal due to TID may also lead to the decrease of phase noise. These results suggest that the use of ILVCOs in satellite systems may be favorable as they are TID radiation tolerant compared to standalone oscillators.
- 12 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. PP (00189499) , 1
System-Level Characterization of Single-Event Effects in Integrated Electronic-Photonic Optical Links for Space-based Communications
This work investigates single-event effects (SEEs) in integrated optical transceivers by experimentally examining subsystem-level vulnerabilities and their contributions to system-level upsets using pulsed-laser testing. A silicon-on-insulator (SOI) electronic photonic integrated circuit (ePIC) implementing an on–off keying (OOK), intensity-modulated direct-detection (IMDD) link is used as a test platform. Individual subsystems are selectively targeted to study single-event transient (SET) generation and propagation across electrical and optical domains. An analytical model is developed to describe electrical-to-optical SET propagation and identify subsystem-specific parameters influencing transient behavior. Experimental results show that, within this platform, SET duration is a key factor in SEU severity, as long transients lead to extended multi-bit upsets. The results of this work highlight the importance of subsystem-level transient characterization to guide targeted radiation-hardened by- design (RHBD) strategies for robust optical communications in space environments.
- 12 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. PP (00189499) , 1
System-Level Characterization of Single-Event Effects in Integrated Electronic-Photonic Optical Links for Space-based Communications
This work investigates single-event effects (SEEs) in integrated optical transceivers by experimentally examining subsystem-level vulnerabilities and their contributions to system-level upsets using pulsed-laser testing. A silicon-on-insulator (SOI) electronic photonic integrated circuit (ePIC) implementing an on–off keying (OOK), intensity-modulated direct-detection (IMDD) link is used as a test platform. Individual subsystems are selectively targeted to study single-event transient (SET) generation and propagation across electrical and optical domains. An analytical model is developed to describe electrical-to-optical SET propagation and identify subsystem-specific parameters influencing transient behavior. Experimental results show that, within this platform, SET duration is a key factor in SEU severity, as long transients lead to extended multi-bit upsets. The results of this work highlight the importance of subsystem-level transient characterization to guide targeted radiation-hardened by- design (RHBD) strategies for robust optical communications in space environments.
- 23 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 72 (3) , 825-847
A Framework for Determining System-Level SEE Vulnerabilities in Wireless RF Receivers
Space-borne wireless communications systems have become ubiquitous with the advent of commercial space flight. To support robust wireless data transmission in Earth-orbiting and deep-space applications, a framework has been developed for radio-frequency (RF) designers and radiation-effects engineers to identify, model, visualize, and test single-event effects (SEEs) in wireless receivers. Digital RF communications receivers are introduced, including the constellation diagram, an important visualization tool. Then, the generation of single-event transients (SETs) is presented in multiple layers, starting from transistors, building to SETs at the outputs of each circuit block, and culminating in the response of the full receiver system. Circuit blocks addressed in this work include a low-noise amplifier (LNA), down-conversion mixer, and voltage-controlled oscillator (VCO). Analytical theory and numerical simulation are synthesized, accompanied with pulsed-laser SEE testing, to give an understanding of how deposited charge in constituent transistors convert to SETs and SEUs. As an example case, a SiGe-BiCMOS direct-conversion receiver carrying 100-Mbaud quadrature phase-shift keying (QPSK) at the X-band (8–12 GHz) is characterized using pulsed-laser SEE testing. This manuscript provides a useful review and analytical template that enable future designers and radiation-effects engineers to (a) model SET propagation in a wireless receiver a priori, without testing full systems, (b) identify the SEE mechanisms present in a wireless receiver with knowledge of the circuit components present, and (c) determine sensitive transistors and circuits to develop informed test plans for worst-case predictions.
- 23 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 72 (3) , 825-847
A Framework for Determining System-Level SEE Vulnerabilities in Wireless RF Receivers
Space-borne wireless communications systems have become ubiquitous with the advent of commercial space flight. To support robust wireless data transmission in Earth-orbiting and deep-space applications, a framework has been developed for radio-frequency (RF) designers and radiation-effects engineers to identify, model, visualize, and test single-event effects (SEEs) in wireless receivers. Digital RF communications receivers are introduced, including the constellation diagram, an important visualization tool. Then, the generation of single-event transients (SETs) is presented in multiple layers, starting from transistors, building to SETs at the outputs of each circuit block, and culminating in the response of the full receiver system. Circuit blocks addressed in this work include a low-noise amplifier (LNA), down-conversion mixer, and voltage-controlled oscillator (VCO). Analytical theory and numerical simulation are synthesized, accompanied with pulsed-laser SEE testing, to give an understanding of how deposited charge in constituent transistors convert to SETs and SEUs. As an example case, a SiGe-BiCMOS direct-conversion receiver carrying 100-Mbaud quadrature phase-shift keying (QPSK) at the X-band (8–12 GHz) is characterized using pulsed-laser SEE testing. This manuscript provides a useful review and analytical template that enable future designers and radiation-effects engineers to (a) model SET propagation in a wireless receiver a priori, without testing full systems, (b) identify the SEE mechanisms present in a wireless receiver with knowledge of the circuit components present, and (c) determine sensitive transistors and circuits to develop informed test plans for worst-case predictions.
- 28 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 72 (2) , 154-163
RF Performance and TID Hardness Tradeoffs in Annular 45-nm RF SOI CMOS Devices
The operability and TID response of 45-nm annular RF SOI nFETs are evaluated and compared with standard layouts. All devices were exposed to 10-keV X-rays, up to a dose of 1 Mrad(SiO2), at both high-gate/low-drain and low-gate/high-drain irradiation conditions. Differences in damage response to DC and small-signal performance between samples are observed as a result of TID-sensitive oxides and their proximity to key transport regions of the devices. Annular FETs are more TID tolerant than standard nFETs, while showing small RF performance tradeoffs as well as lower drive currents and higher threshold voltages. TCAD is used to isolate critical oxides and damage mechanisms in annular and standard layouts to help confirm experimental data and observed damage trends. Taken together, these results suggest that annular FETs represent a valid TID-hardening approach in small-lithography RF SOI CMOS technology platforms for both DC and RF applications.
- 28 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 72 (2) , 154-163
RF Performance and TID Hardness Tradeoffs in Annular 45-nm RF SOI CMOS Devices
The operability and TID response of 45-nm annular RF SOI nFETs are evaluated and compared with standard layouts. All devices were exposed to 10-keV X-rays, up to a dose of 1 Mrad(SiO2), at both high-gate/low-drain and low-gate/high-drain irradiation conditions. Differences in damage response to DC and small-signal performance between samples are observed as a result of TID-sensitive oxides and their proximity to key transport regions of the devices. Annular FETs are more TID tolerant than standard nFETs, while showing small RF performance tradeoffs as well as lower drive currents and higher threshold voltages. TCAD is used to isolate critical oxides and damage mechanisms in annular and standard layouts to help confirm experimental data and observed damage trends. Taken together, these results suggest that annular FETs represent a valid TID-hardening approach in small-lithography RF SOI CMOS technology platforms for both DC and RF applications.
- 7 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 71 (8) , 1691-1698
Comparing Third-Order Digital Modulation Schemes for SEU Resilience in RF Receivers Due to SETs in the SiGe LNA
Three 3 rd -order digital modulation schemes, rectangular 8-quadrature amplitude modulation (8-QAM), 8-phase shift keying (8-PSK), and star 8-QAM are compared for RF receiver-level single-event upset (SEU) sensitivity using laser pulses to strike the low-noise amplifier (LNA). Star 8-QAM had significantly better SEU resilience than 8-PSK and rectangular 8-QAM, suggesting that the choice of the constellation mapping could be effective for mitigating SEUs due to single-event transients (SETs) in the LNAs of RF receivers.
- 7 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 71 (8) , 1691-1698
Comparing Third-Order Digital Modulation Schemes for SEU Resilience in RF Receivers Due to SETs in the SiGe LNA
Three 3 rd -order digital modulation schemes, rectangular 8-quadrature amplitude modulation (8-QAM), 8-phase shift keying (8-PSK), and star 8-QAM are compared for RF receiver-level single-event upset (SEU) sensitivity using laser pulses to strike the low-noise amplifier (LNA). Star 8-QAM had significantly better SEU resilience than 8-PSK and rectangular 8-QAM, suggesting that the choice of the constellation mapping could be effective for mitigating SEUs due to single-event transients (SETs) in the LNAs of RF receivers.
- 12 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 71 (4) , 830-838
SET-Induced Dropout and Recovery of Cross-Coupled and Differential-Colpitts Microwave Oscillators Using SiGe HBTs
RF communications systems in space flight are subject to single-event upsets (SEUs) due to drop-out of the local oscillator during a single-event transient (SET), named here as single-event drop-out (SEDO). If the duration of the SEDO is substantial, it inevitably compromises data. To help alleviate SEUs due to SEDO, the present work compares the drop-out dynamics and recovery times of two types of RF LC oscillators with matched performance: the cross-coupled and the differential-Colpitts. The SEDO responses of both oscillators were tested using a pulsed laser to deposit charge via a two-photon absorption (TPA) process. For matched electrical performance and laser excitation conditions, the Colpitts oscillator demonstrated 14× faster recovery. This improved response was examined using a hybridized circuit/TCAD simulation approach, and it was determined that a lower impedance at the bases of critical oscillating transistors naturally reduces the SEDO sensitivity for Colpitts oscillators. While cross-coupled oscillators are widely used, the present work demonstrates that Colpitts oscillators should instead be considered in frequency synthesizers to mitigate SEUs due to SEDO in oscillators.
- 12 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 71 (4) , 830-838
SET-Induced Dropout and Recovery of Cross-Coupled and Differential-Colpitts Microwave Oscillators Using SiGe HBTs
RF communications systems in space flight are subject to single-event upsets (SEUs) due to drop-out of the local oscillator during a single-event transient (SET), named here as single-event drop-out (SEDO). If the duration of the SEDO is substantial, it inevitably compromises data. To help alleviate SEUs due to SEDO, the present work compares the drop-out dynamics and recovery times of two types of RF LC oscillators with matched performance: the cross-coupled and the differential-Colpitts. The SEDO responses of both oscillators were tested using a pulsed laser to deposit charge via a two-photon absorption (TPA) process. For matched electrical performance and laser excitation conditions, the Colpitts oscillator demonstrated 14× faster recovery. This improved response was examined using a hybridized circuit/TCAD simulation approach, and it was determined that a lower impedance at the bases of critical oscillating transistors naturally reduces the SEDO sensitivity for Colpitts oscillators. While cross-coupled oscillators are widely used, the present work demonstrates that Colpitts oscillators should instead be considered in frequency synthesizers to mitigate SEUs due to SEDO in oscillators.
- 5 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 71 (4) , 816-822
Effects of Collector Profile on the SET Response of 130-nm High-Speed and High-Breakdown SiGe HBTs
A comparison of laser-induced single-event transients in silicon-germanium heterojunction bipolar transistor (SiGe HBT) variants designed for high-speed applications and high-breakdown applications is presented. A significantly lower-amplitude single-event transient (SET) response at low laser pulse energies was observed in the high-speed device compared to the high-breakdown device. At high laser pulse energies, however, the transient amplitudes converged and produced a nearly identical response. A three-dimensional technology computer-aided design (TCAD) model of a SiGe HBT was used to understand the differences between the observed SET responses. During an SET produced by a low laser pulse energy, the mean electric field in the collector-base (CB) junction of a simulated high-breakdown device is shown to have a greater magnitude across the depletion region compared to that of its high-speed counterpart. Motivated by the proportional relationship between drift current and CB junction electric field, a greater breakdown voltage device produced a larger SET response. During an SET produced by a high laser pulse energy, the charge from the SET exceeded the collector doping in both the high-speed and high-breakdown SiGe HBT. This creates a conductive path to the output terminal, removing the dependence of collector doping on SET amplitude. The results of this study should help inform design choices of which device breakdown variant should be used in a given circuit if SETs are a major consideration for the application.
- 5 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 71 (4) , 816-822
Effects of Collector Profile on the SET Response of 130-nm High-Speed and High-Breakdown SiGe HBTs
A comparison of laser-induced single-event transients in silicon-germanium heterojunction bipolar transistor (SiGe HBT) variants designed for high-speed applications and high-breakdown applications is presented. A significantly lower-amplitude single-event transient (SET) response at low laser pulse energies was observed in the high-speed device compared to the high-breakdown device. At high laser pulse energies, however, the transient amplitudes converged and produced a nearly identical response. A three-dimensional technology computer-aided design (TCAD) model of a SiGe HBT was used to understand the differences between the observed SET responses. During an SET produced by a low laser pulse energy, the mean electric field in the collector-base (CB) junction of a simulated high-breakdown device is shown to have a greater magnitude across the depletion region compared to that of its high-speed counterpart. Motivated by the proportional relationship between drift current and CB junction electric field, a greater breakdown voltage device produced a larger SET response. During an SET produced by a high laser pulse energy, the charge from the SET exceeded the collector doping in both the high-speed and high-breakdown SiGe HBT. This creates a conductive path to the output terminal, removing the dependence of collector doping on SET amplitude. The results of this study should help inform design choices of which device breakdown variant should be used in a given circuit if SETs are a major consideration for the application.
- 1 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 71 (4) , 823-829
Comparing Digital Modulation Schemes in RF Receivers for Bit Errors Induced by Single-Event Transients in the Low-Noise Amplifier
Standard digital modulation schemes are compared for receiver-level SEU sensitivity. SETs on the wideband SiGe LNA carrying OOK, BPSK, and 2-FSK modulated data were induced using laser pulses. Both the modulation scheme and its detection method had a significant impact on the SEU sensitivity of the receiver. The SET sensitivity and noise sensitivity of the modulation schemes and demodulation techniques were correlated. Therefore, designing a receiver to be more robust to noise inherently makes it more robust to SETs. For space missions that anticipate a high flux of radiation, taking SETs into account when choosing the RF modulation scheme and the demodulation method may be important to avoid underestimating the total BER when other system trade-offs are compared against the system BER.
- 1 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 71 (4) , 823-829
Comparing Digital Modulation Schemes in RF Receivers for Bit Errors Induced by Single-Event Transients in the Low-Noise Amplifier
Standard digital modulation schemes are compared for receiver-level SEU sensitivity. SETs on the wideband SiGe LNA carrying OOK, BPSK, and 2-FSK modulated data were induced using laser pulses. Both the modulation scheme and its detection method had a significant impact on the SEU sensitivity of the receiver. The SET sensitivity and noise sensitivity of the modulation schemes and demodulation techniques were correlated. Therefore, designing a receiver to be more robust to noise inherently makes it more robust to SETs. For space missions that anticipate a high flux of radiation, taking SETs into account when choosing the RF modulation scheme and the demodulation method may be important to avoid underestimating the total BER when other system trade-offs are compared against the system BER.