YHYuxing Huang

Yuxing Huang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yuxing Huang has a total of 41 co-authors. Here are the top co-authors by number of shared publications:

  • Guanghui Zhang

    School of Mechanical & Electrical Engineering, Guangxi Key Laboratory of Manufacturing Systems and Advanced Manufacturing Technology, Guilin University of Electronic Technology, Guilin, Guangxi 541004, People’s Republic of China

    6 shared publications
  • Yuhong Long

    School of Mechanical & Electrical Engineering, Guangxi Key Laboratory of Manufacturing Systems and Advanced Manufacturing Technology, Guilin University of Electronic Technology, Guilin, China

    6 shared publications
  • Ping Huang

    5 shared publications
  • Yuhong Long

    5 shared publications
  • Hui Jiao

    3 shared publications
  • Hui Jiao

    School of Mechanical and Electrical Engineering, Guangxi Key Laboratory of Manufacturing Systems and Advanced Manufacturing Technology, Guilin University of Electronic Technology 1 , Guilin, Guangxi 541004

    3 shared publications

Latest Publications

  • Thermal lens effect in a high-power infrared laser focusing optical system for water-jet guided laser applications

    by Ping Huang, Zhonggang Xiong, Hongtao Zhang, Bingshen Zhou, Hui Jiao, Yuxing Huang, Yuhong Long, Guanghui Zhang

  • Open Access

    Design and prototype test of integrated equipment for primary processing of small and medium-sized freshwater fish

    by Zhenyang Gao, Gaobin Pu, Xingxuan Huang, Meibing Liang, Yaokai Liu, Wenyi Liu, Yuxing Huang

    To address the low automation, poor consistency, high labor cost and sanitation challenges in primary processing of small and medium-sized freshwater fish in China, this paper presents an integrated processing equipment for crucian carp, bass, bream and tilapia. Adopting a full-process series closed-loop structure, the equipment integrates six core functions: head removal, posture calibration, belly cutting, viscera removal, middle bone removal and synchronous cleaning. Key mechanisms including a turntable head remover, vision-based adaptive flipping mechanism, drop compensation limiter and integrated cutting-deboning actuator are elaborately designed. Core mechanical parameters (cutting force, torque) are calculated and verified, and finite element analysis of the head remover’s meshing structure ensures structural reliability. An intelligent control system with visual recognition, fault warning and safety protection is developed. Prototype tests show it stably processes 100-300mm (50-1000g) fish at 252 fish/h, with 96.2% qualification rate and 7.3% loss rate. Compared with existing equipment, it features compact structure, high integration, low cost and easy operation, effectively meeting the needs of small and medium-sized aquatic processors, central kitchens, prefabricated food enterprises and wholesale markets. This study not only fills the technical gap of cost-effective integrated equipment for primary processing of small and medium-sized freshwater fish, but also provides an engineering example for the cross-integration of food processing machinery with machine vision and embedded control technology. It has important reference value for promoting the development of aquatic processing equipment towards intelligence, miniaturization and low cost, and aligns with the core theme of cross-innovation between mechanical engineering and intelligent manufacturing of this conference.

  • Research on the mechanism of ultrasonic-assisted underwater laser wet welding of 304 stainless steel

    by Jia Zhou, Junjie Zeng, Liao Zhou, Hui Jiao, Yuxing Huang, Li Ouyang, Ruihu Zhu, Yuhong Long

    The dynamic evolution of cavitation bubbles in underwater wet laser welding significantly influences the laser beam. To mitigate the adverse effects of cavitation bubbles, an ultrasonic-assisted underwater laser wet welding method is proposed. This work reports an experimental study of ultrasonic-assisted underwater laser welding 304 stainless steel at varying welding speeds, different water layer thicknesses, and different ultrasonic powers. Additionally, the high-speed photography method was used to analyze the effect of ultrasound on the movement of cavitation bubbles, and a ray optics finite element model was employed to better understand the impact of cavitation positions on the laser beam. The results indicate that, under identical process parameters, the application of ultrasonic waves controls the movement of cavitation bubbles via acoustic flow. Consequently, the weld seam is more uniform, and the width and depth are increased effectively. In addition, without ultrasonic assistance, the weld seam width and depth decrease with higher welding speeds and decrease with the increase of the water layer thickness. With ultrasonic assistance, the weld seam width decreases while the depth increases at higher welding speeds. The weld seam width and depth increase with the increase of ultrasonic power. The weld width first decreases and then increases as the water layer thickness increases, and the weld seam depth shows a decreasing trend. These indicate that the dynamic evolution of cavitation bubbles has an important impact on the weld width and depth. This study can provide a reference for achieving better weld efficiency and geometry in underwater laser wet welding.


  • Open Access

    Mechanistic insights into waterjet-guided laser grooving of silicon: Impact of ablation dynamics, oxide formation, and thermal stress

    by Xinlan Hu, Tielin Shi, Yuhong Long, Yuxing Huang, Guanghui Zhang

    Waterjet-guided laser machining of silicon offers precision with minimal heat-affected zones (HAZs), but understanding the mechanisms behind laser-material interactions remains essential. This study first utilizes orthogonal experiments to reveal fundamental relationships between processing parameters (scanning cycle, laser fluence, scanning velocity, and waterjet pressure) on groove depth and the depth-to-HAZ ratio. These findings guide the in-depth investigation of laser-material mechanisms. The results indicate that the ablation rate decreases with increasing scanning cycles, a phenomenon primarily attributed to the different absorption rates of 532 nm laser light between silicon and silicon dioxide. This conclusion is supported by x-ray photoelectron spectroscopy(XPS) results, which reveal that the accumulation of silicon dioxide occurs as the scanning cycles increase. Additionally, a near-linear relation between the ablation rate and laser fluence is observed, as the ablated area is continuously exposed to high laser intensity regions. However, increasing laser fluence also leads to diminished processing quality due to greater thermal deformation in non-ablating regions. Last, increased scanning velocity is found to cause rougher surfaces, as insufficient heat diffusion leads to higher thermal stress and results in micro-crack formations. The results provide a detailed understanding of the laser-induced transformations in the material and highlight optimal conditions for reducing thermal damage while maintaining machining efficiency. This study advances the field of laser processing by offering insights into the mechanisms governing oxide formation, thermal cracking, and material deformation during silicon grooving, providing the foundation for future exploration of laser-material interaction dynamics.


  • High coupling efficiency with large axial direction coupling adjustment range in water-jet guided laser

    by Guanghui Zhang, Yuxing Huang, Ping Huang, Haoran Ying, Hui Jiao, Jia Zhou, Qingyuan Liu, Tielin Shi, Yuhong Long


  • Open Access

    Numerical investigations of water jet-guided laser cutting of silicon

    by Hui Jiao, Qingyuan Liu, Guanghui Zhang, Ze Lin, Jia Zhou, Yuxing Huang, Yuhong Long

    To investigate the interaction mechanism between a laser, water jet, and substrate, a model is developed to simulate the temperature field evolution and removal process during water jet-guided laser (WJGL) cutting of silicon. The model accounted for the temperature-dependent properties of the silicon absorption coefficient, as well as the physical processes of solid-liquid-gas phase change. A three-dimensional finite volume model of WJGL cutting of silicon is created, incorporating laser energy input, water jet impact-cooling, and silicon phase transition and removal. The volume of fluid (VOF) method is employed to trace the interphase interface and obtain the groove shape. The validity of the model is verified by comparing simulation results with experimental data. The simulation results show that the groove cross section is characterized by a “V” shape. The groove depth nonlinearly increases from 52 to 385 μm with an increasing number of cuts. Additionally, the residual temperature of the silicon substrate rises from 837 to 1345 K as the number of scans increases from 1 to 10. The findings offer valuable insights into WJGL cutting research, specifically shedding light on the intricate details of the laser-water jet-substrate interaction mechanism.


  • Open Access

    Study on thermal effects of high-power laser-coupled water jets and the influence on the stability of water jets

    by Zhen Zhao, Guanghui Zhang, Ze Lin, Jia Zhou, Ping Huang, Hui Jiao, Tielin Shi, Yuxing Huang, Yuhong Long

    In water-guided laser technology, the stability of water jets is crucial to ensure the efficient transmission of laser energy. However, the thermal effects generated when high-power lasers are coupled with water jets are bound to impact the stability of the water jets, thus becoming a critical issue that restricts the development of high-power water-guided laser technology. In addressing this issue, this paper establishes a temperature model for coupling high-power lasers with water jets. Subsequently, with validation of the model's effectiveness through experimental data, simulations are conducted to analyze the temperature distribution within the water jet. During the simulation process, lasers with different parameters were coupled with water jets to analyze the temperature variation law of the water jets. Additionally, the maximum laser power coupled with water jets of different lengths was solved. Based on the calculated temperature values of the water jet, simulate the evolution of its profile over time when it has an initial temperature gradient. Simultaneously, perform a three-dimensional reconstruction of the obtained perturbed profile and conduct ray tracing to analyze the laser's transmission losses within the perturbed profile. Finally, high-speed cameras are utilized to capture the profile of the water jet, validating the laser-induced fragmentation behavior in the water jet. The research findings will provide a significant reference value for selecting laser parameters and controlling thermal effects in water-guided high-power technology.


  • Research on laser beams focusing and coupling technology of water jet guided laser with high adjustment tolerance

    by Yuxing Huang, En Liang, Guanghui Zhang, Liao Zhou, Ping Huang, Hui Jiao, Jia Zhou, Zhixian Zhong, Tielin Shi, Yuhong Long