TATariq Anwar Aquib

Tariq Anwar Aquib

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Tariq Anwar Aquib has a total of 6 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Seismic fragility assessment of reinforced concrete frames with soft brick URM infills

    by Jayaprakash Vemuri, Tariq Anwar Aquib, K. V. L. Subramaniam

    Soft brick masonry infills are widely used in reinforced concrete (RC) frames in developing countries, particularly in India. However, most existing experimental and numerical studies have focused on stiff brick masonry, and there is limited literature specifically addressing the behaviour of RC frames with soft brick unreinforced masonry (URM) infills. The frame–infill interaction is governed primarily by their relative stiffness, meaning that conclusions drawn from stiff infill research cannot be directly extrapolated to soft brick infills. This study investigates the in-plane behaviour of RC frames with soft brick masonry infills through detailed numerical analysis. A micro-modelling approach is adopted to accurately represent the soft brick URM infill. Monotonic lateral loading is applied to examine the complex frame–infill interaction mechanisms and to evaluate interfacial tractions. A parametric study is conducted to assess the influence of infill wall aspect ratio on lateral strength, stiffness, and failure modes. The development and characteristics of diagonal compression struts are analysed, and effective strut widths are determined. Furthermore, nonlinear time-history analyses (NTHA) are performed on the infilled frame using the equivalent strut modelling approach. The results are combined with limit states prescribed by relevant Indian Standards (IS codes) as well as additional damage states identified from the detailed micro-models. Seismic fragility curves are derived for the bare frame, the infill panel alone, and the composite infilled frame. The fragility assessment reveals that infilled frames with higher aspect ratios exhibit significantly lower seismic vulnerability, sustaining considerably higher peak ground acceleration (PGA) levels before reaching various damage states.


  • Open Access

    Machine learning based Pseudo-Dynamic rupture generator for geometric rough faults

    by Tariq Anwar Aquib, David Castro Cruz, Jagdish Vyas, Paul Martin Mai

    Accurately predicting the intensity and variability of strong ground motions from future large earthquakes is crucial for seismic hazard analysis. While kinematic ground motion simulations are computationally efficient and can be conditioned to inferred source-inversion models of past events or ensemble statistics of rupture-model databases, they rely on predefined spatiotemporal evolution of slip. In contrast, dynamic rupture simulations solve for a physically self-consistent slip evolution under prescribed stress and friction laws on the fault, yet, they are still computationally expensive. A practical compromise, therefore, is a physics-compatible source model embedded in a kinematic approach (i.e., Guatteri et al., 2004), referred to as the Pseudo-Dynamic (PD) approach.Geologic features, such as small-scale fault roughness influence the rupture process, generating realistic high frequency radiation with decay characteristics (Mai et al., 2017). Presently, most PD models are based on rupture simulations of planar faults (with the notable exception of Savran and Olsen, 2020). Additionally, these models rely on 1-point and 2-point statistics between source parameters, which may not adequately capture nonlinear relationships between kinematic rupture parameters.In this study, we develop a Machine Learning (ML) framework involving Fourier Neural operators (FNO) (Li et al ., 2020) to learn the interdependencies between earthquake source parameters. We train our model using 21 dynamic simulations of rough faults (15 for training, 6 for testing; all from Mai et al., 2017). Our generator initiates with a stochastic final slip (Mai and Beroza, 2002) and a slip-constrained hypocentre location (Mai et al., 2005). The local slip evolution is described by a regularized Yoffe source time function (STF) characterized by rupture onset time, slip, peak time and rise time.Dynamic rupture simulations show correlation between rupture speed and the gradient of fault roughness, with rupture deceleration in regions of positive roughness gradients, coinciding with fault areas of increased shear stress. Therefore, we establish rupture speed as a function of stress drop computed from 2D final slip and relate peak slip velocity to the estimated rupture speed. Assuming a Yoffe STF, we then compute rise time and the time of peak slip velocity, enabling a full spatiotemporal earthquake source characterization that accounts for dynamic rupture on rough faults. For the stochastic slip, we also demonstrate an approach to model roughness correlated with stress drop. Our PD rupture generator reproduces the mean and standard deviation of ground motion models for different intensity measures in simulations of M 6.0-7.0 strike slip scenarios. This outlines a new PD source modelling approach suitable for broadband physics-based probabilistic seismic hazard analysis.

  • Open Access

    Simulation of ground motions with high frequency components obtained from Fourier neural operators

    by Tariq Anwar Aquib, Paul Martin Mai

    Seismic hazards analysis relies on accurate knowledge of ground motions arising from potential earthquakes to assess the risk of damage to buildings and infrastructure. It is necessary to perform ground motion simulations because recorded strong-motion data from specific combinations of earthquake magnitudes, epicentral distances, and site conditions are still limited. Physics-based simulations provide reliable ground motion estimates, but their application in practice is limited to frequency ranges f < 1Hz, largely due to limited computational resources and lack of information regarding earthquake sources and medium. While hybrid ground-motion computations combining deterministic low frequency components with stochastic high frequency components are often used, their stochastic high frequency components fail to correctly account for source and path effects and lead to inconsistent building responses.The large database of ground motion records from Japan lends itself to develop machine learning approaches to estimate high frequency ground motions. Applying state-of-the-art machine learning techniques, like Fourier neural operators (FNOs) and Generative Adversarial Networks (GANs), we estimate seismograms at higher frequencies from their low frequency counterparts. In our approach, the time and frequency properties of ground motions are estimated using two different FNO models. In the time domain, a relationship is established between normalised low pass filtered and broadband waveforms. Frequency domain analysis involves the learning of high frequency spectrum from low frequency spectrum. Finally, the time and frequency properties are combined to produce broadband ground motions. Source, site, and path aspects are naturally incorporated into the training process.We use ground motion data collected between 1996 and 2020 at 18 stations in the Ibaraki province of Japan to train our models and validate them on different events (Mw 4 to 7) around Japan. Using goodness of fit measures (GOFs), we show that the resulting ground motions match the recorded observations with good to acceptable GOF values for most of the predictions. To enhance our predictions, we include uncertainty estimation by utilizing a conditioned GAN approach. Lastly, to demonstrate the practicality of the approach, we compute high frequency components for a physics based simulated hypothetical Mw 5.0 earthquake in Japan.

  • Open Access

    Analysis of Ground Motion Intensity Measures and Selection Techniques for Estimating Building Response

    by Tariq A. Aquib, Jayalakshmi Sivasubramonian, P. Martin Mai

    The structural response of buildings to earthquake shaking is of critical importance for seismic design purposes. Research on the relationship between earthquake ground motion intensity, building response, and seismic risk is ongoing, but not yet fully conclusive. Often, probability demand models rely on one ground motion intensity measure (IM) to predict the engineering demand parameter (EDP). The engineering community has suggested several IMs to account for different ground motion characteristics, but there is no single optimal IM. For this study, we compile a comprehensive list of IMs and their characteristics to assist engineers in making an informed decision. We discuss the ground motion selection process used for dynamic analysis of structural systems. For illustration, we compute building responses of 2D frames with different natural period subjected to more than 3500 recorded earthquake ground motions. Using our analysis, we examine the effects of different structural characteristics and seismological parameters on EDP-IM relationships by applying multi-regression models and statistical inter-model comparisons. As such, our results support and augment previous studies and suggest further improvements on the relationship between EDP and IM in terms of efficiency and sufficiency. Finally, we provide guidance on future approaches to the selection of both optimal intensity measures and ground motions using newer techniques.