Leyner Cardenas-Mercado
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Leyner Cardenas-Mercado has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Andrea Nardini
Department of Life Sciences, University of Trieste, via L. Giorgieri 10, 34127 Trieste, Italy
1 shared publication - Andrés Torres
Instituto Javeriano del Agua, Pontificia Universidad Javeriana, Carrera 7ª No. 40-62, Bogotá, Colombia
1 shared publication Jhonny I. Pérez-Montiel
1 shared publication- Jhonny Isaac Perez Montiel
Grupo de Investigación GISA, Facultad de Ingeniería, Universidad de La Guajira, km 3 + 354 Vía a Maicao, Riohacha 440007, Colombia
1 shared publication Jorge Escobar-Vargas
1 shared publication
Latest Publications
- Open Access
- 20 July 2023
- Published by Elsevier in Journal of Hydrology
- Vol. 625
Integration of physically-based numerical tools and socio-hydrological variables in urban flood modeling
- 20 July 2023
- Published by Elsevier in Journal of Hydrology
- Vol. 625
Open AccessIntegration of physically-based numerical tools and socio-hydrological variables in urban flood modeling
- Open Access
Flood Modeling in a Coastal Town in Northern Colombia: Comparing MODCEL vs. IBER
In Riohacha the La Niña, phenomenon generates intense rains with consequent serious flooding. To address this reality, MODCEL, a conceptual cell-based model, had been applied and calibrated in a previous project. In this research, we compare MODCEL with IBER, a well-known, physically based 2D hydraulic model. The purpose is twofold: (i) to illustrate how system schematization can be carried out in the two modeling frameworks, which is not a trivial task and implies several choices and assumptions; (ii) to point out the strengths and weaknesses of these two models in a comparative fashion. Here, IBER has been calibrated and validated with the same data used for MODCEL. MODCEL performs slightly better, both in calibration and validation possibly because of the low resolution of the topographic information, an essential element for IBER. Furthermore, in IBER it is not possible to represent adequately all the different hydraulic works spread across the town. MODCEL, in turn, is not easy to apply because it requires a deep insight into the actual behavior of the physical system and time-consuming schematization attempts where a deep experience is needed; furthermore, it is by far less user-friendly than IBER. In any case, the two models capture sufficiently well the behavior of urban flooding and its changes according to hypothetical interventions.
Open AccessFlood Modeling in a Coastal Town in Northern Colombia: Comparing MODCEL vs. IBER
In Riohacha the La Niña, phenomenon generates intense rains with consequent serious flooding. To address this reality, MODCEL, a conceptual cell-based model, had been applied and calibrated in a previous project. In this research, we compare MODCEL with IBER, a well-known, physically based 2D hydraulic model. The purpose is twofold: (i) to illustrate how system schematization can be carried out in the two modeling frameworks, which is not a trivial task and implies several choices and assumptions; (ii) to point out the strengths and weaknesses of these two models in a comparative fashion. Here, IBER has been calibrated and validated with the same data used for MODCEL. MODCEL performs slightly better, both in calibration and validation possibly because of the low resolution of the topographic information, an essential element for IBER. Furthermore, in IBER it is not possible to represent adequately all the different hydraulic works spread across the town. MODCEL, in turn, is not easy to apply because it requires a deep insight into the actual behavior of the physical system and time-consuming schematization attempts where a deep experience is needed; furthermore, it is by far less user-friendly than IBER. In any case, the two models capture sufficiently well the behavior of urban flooding and its changes according to hypothetical interventions.
- Open Access
- 26 July 2022
- Published by Editorial Pontificia Universidad Javeriana
Integración de herramientas numéricas de base física y variables socio-hidrológicas en la modelación de inundaciones urbanas
En el presente trabajo se propone un enfoque metodológico para el modelado de inundaciones urbanas, que integra herramientas numéricas basadas en variables físicas y socio-hidrológicas (SH-V). Esta metodología se aplica al estudio de caso de la ciudad de Riohacha (Colombia). Se encontraron correlaciones entre SH-V y el comportamiento de las inundaciones mediante pruebas univariadas y multivariadas. Se utilizó TELEMAC-2D como modelo para simular un evento de inundación extrema y se llevó a cabo un proceso iterativo utilizando Maquinas de Soporte Vectorial - SVM para optimizar la calibración del modelo. Se evaluaron métricas de desempeño hasta encontrar los valores óptimos del número de curva - CN y el coeficiente de fricción de Manning. Los resultados muestran que SH-V brinda información valiosa sobre el comportamiento de la inundación y puede representar mejor los parámetros hidráulicos como CN y coeficientes de fricción para fines de modelado. La metodología propuesta se establece como una herramienta para optimizar los procesos de modelado.
- 26 July 2022
- Published by Editorial Pontificia Universidad Javeriana
Open AccessIntegración de herramientas numéricas de base física y variables socio-hidrológicas en la modelación de inundaciones urbanas
En el presente trabajo se propone un enfoque metodológico para el modelado de inundaciones urbanas, que integra herramientas numéricas basadas en variables físicas y socio-hidrológicas (SH-V). Esta metodología se aplica al estudio de caso de la ciudad de Riohacha (Colombia). Se encontraron correlaciones entre SH-V y el comportamiento de las inundaciones mediante pruebas univariadas y multivariadas. Se utilizó TELEMAC-2D como modelo para simular un evento de inundación extrema y se llevó a cabo un proceso iterativo utilizando Maquinas de Soporte Vectorial - SVM para optimizar la calibración del modelo. Se evaluaron métricas de desempeño hasta encontrar los valores óptimos del número de curva - CN y el coeficiente de fricción de Manning. Los resultados muestran que SH-V brinda información valiosa sobre el comportamiento de la inundación y puede representar mejor los parámetros hidráulicos como CN y coeficientes de fricción para fines de modelado. La metodología propuesta se establece como una herramienta para optimizar los procesos de modelado.