Kun Huang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Kun Huang has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Cheng Huang
School of New Energy and Materials, Southwest Petroleum University, Chengdu 610500, China
1 shared publication - Hongfang Lu
State Key Laboratory of Advanced Marine Materials, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences
1 shared publication - Juan Chen
School of Mechatronic Engineering, Southwest Petroleum University, Chengdu 610500, China
1 shared publication - Kun Chen
Petroleum Engineering School, Southwest Petroleum University, Chengdu 610500, China
1 shared publication - Lin Wang
School of Mechatronic Engineering, Southwest Petroleum University, Chengdu 610500, China
1 shared publication Shijuan Wu
State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation, Southwest Petroleum University, Chengdu, Sichuan, China; School of Petroleum Engineering, Southwest Petroleum University, Chengdu, Sichuan, China
1 shared publication
Latest Publications
- Open Access
Research on Process of SCV Flue Gas Carbon Capture Based on LNG Cold Energy
Under the guidance of China’s goal of achieving carbon neutrality by 2060, the petrochemical industry is increasingly adopting energy-saving and emission-reduction technologies. To realize the low carbon operation of the LNG (liquefied natural gas) receiving terminal, an innovative SCV (submerged combustion vaporizer) flue gas carbon capture system using LNG cold energy was established, and the system also combined with an ORC (organic Rankine cycle). HYSYS software was used to simulate the process of the SCV flue gas carbon capture system and the LNG regasification system. The simulation results showed that the proposed system has low carbon emission and low energy consumption performance. Moreover, the sensitivity analysis of the evaporation pressure of working fluids, CO2 capture pressure, and CO2 capture temperature was carried out. The key parameters were optimized by HYSYS software to achieve the optimal operation cost of the system. When the evaporation pressure of working fluids, CO2 capture pressure, and CO2 capture temperature were set as 1300 kPa, 750 kPa, and 143.15 K, respectively, the optimized system resulted in an exergy efficiency of 13.63%, an LNG cold exergy utilization rate of 77.49%, a CO2 capture rate of 94.9%, and a CO2 capture capacity of 6620.4 kg/h.
Open AccessResearch on Process of SCV Flue Gas Carbon Capture Based on LNG Cold Energy
Under the guidance of China’s goal of achieving carbon neutrality by 2060, the petrochemical industry is increasingly adopting energy-saving and emission-reduction technologies. To realize the low carbon operation of the LNG (liquefied natural gas) receiving terminal, an innovative SCV (submerged combustion vaporizer) flue gas carbon capture system using LNG cold energy was established, and the system also combined with an ORC (organic Rankine cycle). HYSYS software was used to simulate the process of the SCV flue gas carbon capture system and the LNG regasification system. The simulation results showed that the proposed system has low carbon emission and low energy consumption performance. Moreover, the sensitivity analysis of the evaporation pressure of working fluids, CO2 capture pressure, and CO2 capture temperature was carried out. The key parameters were optimized by HYSYS software to achieve the optimal operation cost of the system. When the evaporation pressure of working fluids, CO2 capture pressure, and CO2 capture temperature were set as 1300 kPa, 750 kPa, and 143.15 K, respectively, the optimized system resulted in an exergy efficiency of 13.63%, an LNG cold exergy utilization rate of 77.49%, a CO2 capture rate of 94.9%, and a CO2 capture capacity of 6620.4 kg/h.
- Open Access
- 18 February 2015
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 10 (2) , e0115299
Frequency Spectrum Method-Based Stress Analysis for Oil Pipelines in Earthquake Disaster Areas
When a long distance oil pipeline crosses an earthquake disaster area, inertial force and strong ground motion can cause the pipeline stress to exceed the failure limit, resulting in bending and deformation failure. To date, researchers have performed limited safety analyses of oil pipelines in earthquake disaster areas that include stress analysis. Therefore, using the spectrum method and theory of one-dimensional beam units, CAESAR II is used to perform a dynamic earthquake analysis for an oil pipeline in the XX earthquake disaster area. This software is used to determine if the displacement and stress of the pipeline meet the standards when subjected to a strong earthquake. After performing the numerical analysis, the primary seismic action axial, longitudinal and horizontal displacement directions and the critical section of the pipeline can be located. Feasible project enhancement suggestions based on the analysis results are proposed. The designer is able to utilize this stress analysis method to perform an ultimate design for an oil pipeline in earthquake disaster areas; therefore, improving the safe operation of the pipeline.
- 18 February 2015
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 10 (2) , e0115299
Open AccessFrequency Spectrum Method-Based Stress Analysis for Oil Pipelines in Earthquake Disaster Areas
When a long distance oil pipeline crosses an earthquake disaster area, inertial force and strong ground motion can cause the pipeline stress to exceed the failure limit, resulting in bending and deformation failure. To date, researchers have performed limited safety analyses of oil pipelines in earthquake disaster areas that include stress analysis. Therefore, using the spectrum method and theory of one-dimensional beam units, CAESAR II is used to perform a dynamic earthquake analysis for an oil pipeline in the XX earthquake disaster area. This software is used to determine if the displacement and stress of the pipeline meet the standards when subjected to a strong earthquake. After performing the numerical analysis, the primary seismic action axial, longitudinal and horizontal displacement directions and the critical section of the pipeline can be located. Feasible project enhancement suggestions based on the analysis results are proposed. The designer is able to utilize this stress analysis method to perform an ultimate design for an oil pipeline in earthquake disaster areas; therefore, improving the safe operation of the pipeline.