Othmane Rayan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Othmane Rayan has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
Abderrazak El Ouafi
Département de Mathématiques, d’Informatique et de Génie, Université du Québec à Rimouski, Rimouski, Canada
3 shared publicationsClaude Belzile
3 shared publicationsJean Brousseau
3 shared publications- Jean Brousseau
University of Quebec at Rimouski Rimouski Quebec Canada
2 shared publications - Adam Trindade1 shared publication
- Claude Belzile
Institut des sciences de la mer de Rimouski, Université du Québec à Rimouski, Rimouski, Québec, Canada
1 shared publication
Latest Publications
- 23 August 2025
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 10 (12) , 11697-11709
Evaluation of the chemical resistance of selective laser-sintered PA12 pieces for food industry machinery applications
- 23 August 2025
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 10 (12) , 11697-11709
Evaluation of the chemical resistance of selective laser-sintered PA12 pieces for food industry machinery applications
- Open Access
- 29 September 2023
- Published by AccScience Publishing in Materials Science in Additive Manufacturing
- Vol. 2 (3) , 1781
Maraging steel powder alteration caused by laser powder bed fusion printing process
Metallic additive manufacturing (AM) technologies have recently drawn a lot of interest, notably in the aerospace, automotive, and biomedical fields, as they allow a great degree of design flexibility, perform well mechanically, and reduce material waste. As long as the unfused powder is sieved and recycled for the next print, AM is a green and clean process. However, the recycled powder is prone to several modifications during the course of printing that may affect the mechanical properties of finished components. The study examines the phenomenon of powder degradation caused by laser powder bed fusion printing process and the reuse of the powder. Maraging steel was chosen because there are very few studies on the alteration of this type of powder. The effects of part location, distance between parts and lattice structure on powder characteristics were investigated. Results showed that powder particles were not uniformly distributed over the powder bed, coarsening toward the collecting bin. Nevertheless, the gas filtration system that transports spatters and fumes had no noticeable effect on the powder bed particle-size distribution (PSD). Analyses of the powder spread over the build plate revealed that the PSD shifted toward larger particles with a considerable drop in the percentage of fine particles as the spacing between printed parts was decreased. Printing lattice structures had a substantial impact on the PSD of the powder bed. The size of the particles increased remarkably as the lattice cell became tighter, while the powder morphology showed a huge amount of spatters, aggregates, “clip-clap,” elongated particles, broken particles, shattered, and deformed particles. Taken together, the study showed that the PSD of the powder became coarser and the particle morphology was altered as the number of reuses increased.
- 29 September 2023
- Published by AccScience Publishing in Materials Science in Additive Manufacturing
- Vol. 2 (3) , 1781
Open AccessMaraging steel powder alteration caused by laser powder bed fusion printing process
Metallic additive manufacturing (AM) technologies have recently drawn a lot of interest, notably in the aerospace, automotive, and biomedical fields, as they allow a great degree of design flexibility, perform well mechanically, and reduce material waste. As long as the unfused powder is sieved and recycled for the next print, AM is a green and clean process. However, the recycled powder is prone to several modifications during the course of printing that may affect the mechanical properties of finished components. The study examines the phenomenon of powder degradation caused by laser powder bed fusion printing process and the reuse of the powder. Maraging steel was chosen because there are very few studies on the alteration of this type of powder. The effects of part location, distance between parts and lattice structure on powder characteristics were investigated. Results showed that powder particles were not uniformly distributed over the powder bed, coarsening toward the collecting bin. Nevertheless, the gas filtration system that transports spatters and fumes had no noticeable effect on the powder bed particle-size distribution (PSD). Analyses of the powder spread over the build plate revealed that the PSD shifted toward larger particles with a considerable drop in the percentage of fine particles as the spacing between printed parts was decreased. Printing lattice structures had a substantial impact on the PSD of the powder bed. The size of the particles increased remarkably as the lattice cell became tighter, while the powder morphology showed a huge amount of spatters, aggregates, “clip-clap,” elongated particles, broken particles, shattered, and deformed particles. Taken together, the study showed that the PSD of the powder became coarser and the particle morphology was altered as the number of reuses increased.
- Open Access
- 29 November 2022
- Published by Springer Nature in Research Square
Maraging Steel Powder Recycling Effect on the Tensile and Fatigue Behavior of Parts Produced Through the Laser Powder Bed Fusion (L-PBF) Process
Additive manufacturing (AM) has advanced the manufacturing industry and has been employed in a wide range of industrial applications, including in aerospace, automotive, medical and die-casting equipment. To ensure the cost-effectiveness of the AM process, unfused powder must be recycled even if its characteristics may change after each cycle, making essential the validation of powder quality and component mechanical performances. Despite the research published to date, predicting the mechanical performance of printed parts issued from reused powder remains challenging since it is dependent on many AM process variables. Until now, no research has looked at the impact of powder recycling on the fatigue behavior of maraging steel components. This study investigates the impact of maraging steel powder reuse on powder characteristics, as well as on the tensile and fatigue properties of printed components. Our results indicate that the powder particle size distribution increased after eight powder recycling, particle morphology showed the presence of aggregates, broken particles, shattered and deformed particles, while powder apparent density remained constant. Powder reusing had no significant impact on the surface roughness of as-built specimens. Although there was a slight decrease in mechanical properties over reuse cycles, tensile and fatigue performance remained globally stable, while the standard deviation of fatigue stress became narrower after eight cycles. Finally, fractography revealed that the fatigue fracture surfaces of components manufactured from an eight-time recycled powder have more fusion defects and carbon inclusions than the parts made from virgin powder.
- 29 November 2022
- Published by Springer Nature in Research Square
Open AccessMaraging Steel Powder Recycling Effect on the Tensile and Fatigue Behavior of Parts Produced Through the Laser Powder Bed Fusion (L-PBF) Process
Additive manufacturing (AM) has advanced the manufacturing industry and has been employed in a wide range of industrial applications, including in aerospace, automotive, medical and die-casting equipment. To ensure the cost-effectiveness of the AM process, unfused powder must be recycled even if its characteristics may change after each cycle, making essential the validation of powder quality and component mechanical performances. Despite the research published to date, predicting the mechanical performance of printed parts issued from reused powder remains challenging since it is dependent on many AM process variables. Until now, no research has looked at the impact of powder recycling on the fatigue behavior of maraging steel components. This study investigates the impact of maraging steel powder reuse on powder characteristics, as well as on the tensile and fatigue properties of printed components. Our results indicate that the powder particle size distribution increased after eight powder recycling, particle morphology showed the presence of aggregates, broken particles, shattered and deformed particles, while powder apparent density remained constant. Powder reusing had no significant impact on the surface roughness of as-built specimens. Although there was a slight decrease in mechanical properties over reuse cycles, tensile and fatigue performance remained globally stable, while the standard deviation of fatigue stress became narrower after eight cycles. Finally, fractography revealed that the fatigue fracture surfaces of components manufactured from an eight-time recycled powder have more fusion defects and carbon inclusions than the parts made from virgin powder.
- Open Access
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Maraging Steel Powder Alteration Caused by 3D Printing Process and Powder Recycling
Metallic additive manufacturing (AM) technologies have recently drawn a lot of interest, notably in the aerospace, automotive, and biomedical fields, as they allow a great degree of design flexibility, perform well mechanically, and reduce material waste. As long as the unfused powder is sieved and recycled for the next print, AM is a green and clean process. However, the recycled powder is prone to several modifications during the course of printing that may affect the mechanical properties of finished components. The study examines the phenomenon of powder degradation caused by laser powder bed fusion (L-PBF) printing process and the reuse of the powder. The experiments were conducted on a laser powder bed fusion printer. Maraging steel was chosen because there are very few studies on the alteration of this type of powder. The effects of part location, distance between parts, lattice structure on powder characteristics are investigated. Results show that powder particles are not uniformly distributed over the powder bed, coarsening toward the collecting bin. Nevertheless, the gas filtration system that transports spatters and fumes has no noticeable effect on the powder bed particle-size distribution (PSD). Analyses of the powder spread over the build plate reveal that the PSD shifts toward larger particles with a considerable drop in the percentage of fine particles as the spacing between printed parts is decreased. Printing lattice structures have a substantial impact on the PSD of the powder bed and produced a huge amount of spatters, aggregates, ‘‘Clip-Clap”, elongated particles, broken particles, shattered and deformed particles. As the study shows, the PSD of the powder became coarser and their particles morphology was altered after 12 reuses.
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Open AccessMaraging Steel Powder Alteration Caused by 3D Printing Process and Powder Recycling
Metallic additive manufacturing (AM) technologies have recently drawn a lot of interest, notably in the aerospace, automotive, and biomedical fields, as they allow a great degree of design flexibility, perform well mechanically, and reduce material waste. As long as the unfused powder is sieved and recycled for the next print, AM is a green and clean process. However, the recycled powder is prone to several modifications during the course of printing that may affect the mechanical properties of finished components. The study examines the phenomenon of powder degradation caused by laser powder bed fusion (L-PBF) printing process and the reuse of the powder. The experiments were conducted on a laser powder bed fusion printer. Maraging steel was chosen because there are very few studies on the alteration of this type of powder. The effects of part location, distance between parts, lattice structure on powder characteristics are investigated. Results show that powder particles are not uniformly distributed over the powder bed, coarsening toward the collecting bin. Nevertheless, the gas filtration system that transports spatters and fumes has no noticeable effect on the powder bed particle-size distribution (PSD). Analyses of the powder spread over the build plate reveal that the PSD shifts toward larger particles with a considerable drop in the percentage of fine particles as the spacing between printed parts is decreased. Printing lattice structures have a substantial impact on the PSD of the powder bed and produced a huge amount of spatters, aggregates, ‘‘Clip-Clap”, elongated particles, broken particles, shattered and deformed particles. As the study shows, the PSD of the powder became coarser and their particles morphology was altered after 12 reuses.