PWPuji Widiyanto

Puji Widiyanto

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Puji Widiyanto has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Small signal modeling of restructured boost converter in continuous conduction mode

    by Anwar Muqorobin, Sulistyo Wijanarko, Muhammad Kasim, Pudji Irasari, Ketut Wirtayasa, Puji Widiyanto

    This paper introduces small signal modeling of the restructured boost converter (RBC) in continuous conduction mode (CCM) by using the circuit averaging technique. The averaging technique produces linear transfer functions of the converter. The transfer functions relating the duty cycle to output voltage, duty cycle to inductor current, input voltage to output voltage, and input voltage to inductor current are obtained. To validate the converter model, power simulation (PSIM) simulations are developed, and experiments are conducted. The function of RBC is similar to a conventional boost converter, i.e., to level up the input voltage. A comparative analysis between the RBC and conventional boost converter is performed. The results highlight the advantages of RBC over a conventional boost converter.

  • Open Access

    Permanent magnet generator performance comparison under different topologies and capacities

    by Ketut Wirtayasa, Muhammad Kasim, Puji Widiyanto, Anwar Muqorobin, Sulistyo Wijanarko, Pudji Irasari

    This paper compares the magnetic, electrical, and mechanical characteristics of two permanent magnet generator topologies: single-gap axial flux and single-gap inner rotor radial flux. The study aims to identify how the key parameters fluctuate at each power capacity and investigate the trends in their values as power changes. The power capacities observed are 300 W, 600 W, 900 W, 1200 W, and 1500 W. Simulations used with the help of Ansys Maxwell software to obtain: i) magnetic characteristics without load, including air gap flux density, flux linkage, and induced voltage, ii) electrical performance, consisting of armature current, terminal voltage, voltage regulation, total harmonic distortion, core loss and output power, and iii) mechanical performance, including shaft torque and cogging torque. The last step compares the power density of both topologies. The simulation results show that the axial flux permanent magnet generator (AFPMG) has better air gap flux density, voltage regulation, total harmonic distortion (THD), efficiency, electromagnetic torque, and power density characteristics. Meanwhile, the radial flux permanent magnet generator (RFPMG) is superior in induced voltage and output power. These results conclude that, in general, AFPMG is exceptional from a technical point of view and is more economical when applied to hydro or wind energy systems.

  • Open Access

    A double-Gaussian wake model considering yaw misalignment

    by Qidun Soesanto, Qidir Soesanto, Puji Widiyanto

    A wake steering has been known to effectively increase wind farm production by deflecting the upstream turbines’ wakes via yaw misalignment, thus minimizing their negative impacts on the downstream turbines' performances. This study presents analytical modeling of horizontal-axis wind turbine (HAWT) wake using low-cost analytical modeling as an alternative to expensive numerical and experimental trials. The existing double-Gaussian (DG) analytical wake model was modified to include the yaw misalignment effect, allowing its usability for the yawed HAWT wake modeling. The benchmark dataset produced by high-fidelity large eddy simulation (LES) of wake flowfields behind the turbine with yaw angles of 0º, 10º, 20º, and 30º were used to validate the accuracy of the DG yaw wake model. Overall, the DG yaw wake model predictions showed good agreement with the benchmark dataset under varying HAWT rotor yaw configurations. The analytical results verified by the LES dataset confirm the effectiveness of yaw misalignment in deflecting the wake trajectory, expediting the wake recovery downstream of the HAWT. In addition, a higher rotor yaw angle improves the wake recovery rate in the prevailing wind direction. Notable deviations against the benchmark dataset were found mainly within the near-wake region owing to flow acceleration arising from turbine-induced turbulence. As a result, the model’s predictions were slightly lower than the benchmark dataset, most likely due to neglecting the acceleration term in the analytical model derivation. Otherwise, the analytical model could accurately predict the mean wake velocity within the far-wake region for all evaluated cases, demonstrating its reliability in estimating wind speed potential within a practical distance for micrositing. These results were also proved quantitatively by statistical evaluations utilizing root mean square error (RMSE) and Pearson correlation coefficient R. The present study points out the importance of the upstream HAWTs’ rotor yaw controls to properly deflect their wakes away from their mainstream trajectories, thus effectively maximizing the wind speed potentials extracted by the downstream HAWTs and improving the overall wind farm production.


  • Open Access

    Feasibility analysis of the conversion of brushed to brushless direct current motor

    by Pudji Irasari, Puji Widiyanto, Anwar Muqorobin, Muhammad Fathul Hikmawan

    This paper analyzes the feasibility of converting brushed direct current (BDC) to brushless direct current (BLDC) motor by substituting the wound rotor with a permanent magnet. The aim is to overcome the low quality of rewinding of wound rotors. The conversion was performed by redesigning the motor, referring to the old stator dimensions and motor specifications. Some suitable speed control systems were also examined. Technical analysis was executed by simulating motor characteristics, covering torque-speed curve, cogging, and ripple torques. Afterward, an economic analysis was done to determine the cost of making one rotor unit and the speed control and then compare it with the price of a new BDC motor with equivalent power. The results show that the motor produces 3.6 kW, 18.86 V, 176.71 A, and 28.53 Nm at 2,460 rpm with 2 phases configuration. The maximum cogging torque is 2.9 Nm. The cost of making one rotor unit plus speed control is higher than that of a new BDC motor. These results show that it is technically feasible to convert BDC into a BLDC motor but not economically or vice versa.


  • Open Access

    Performance analyzes of a compact pico hydropower plant with a wide operating range

    by Pudji Irasari, Anwar Muqorobin, Puji Widiyanto, Tajuddin Nur, I Nengah Diasta, Priyono Soetikno

    This paper analyzes the performance of a pico hydropower plant consisting of an axial hydro turbine integrated with a permanent magnet generator (PMG) and connected to a power converter. The proposed system is aimed to obtain a wide system operation range to gain more power captured while maintaining time-harmonic distortion in voltage (THDv) that meets the standard. The PMG specification is 1 kW, 1 phase, 235 V, 50 Hz, 83 rpm. The design and simulation of PMG were carried out by analytical and numerical calculations using FEMM 4.2. The power converter was simulated using PSIM and functions to reduce the THDv and pass the generator voltage between 50–500 V. The results show the THDv of the generating system at the upper and lower limits of the passed voltage having a THDv below 5%. Meanwhile, the PMG performance characteristics at various currents and rotations produce efficiency of 87.20% at nominal current. From these results, it can be concluded that the pico hydropower plant works well as desired.