Changhong Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Changhong Liu has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Hanying Wang
School of Materials, Zhengzhou University of Aeronautics, Zhengzhou 450046, China
2 shared publications - Xiaoqin Guo
Henan Key Laboratory of Aeronautical Materials and Application Technology, School of Material Science and Engineering, Zhengzhou University of Aeronautics, Zhengzhou, China
2 shared publications - Xin Zhao
School of Materials, Zhengzhou University of Aeronautics, Zhengzhou 450046, China
2 shared publications - Xinfang Zhang
School of Materials Science and Engineering, Zhengzhou University of Aeronautics, Zhengzhou 450046, China
2 shared publications - Yizhuang Zhang
School of Materials, Zhengzhou University of Aeronautics, Zhengzhou 450046, China
2 shared publications - Yunpeng Ding
Zhengzhou University of Aeronautics
2 shared publications
Latest Publications
- Open Access
Microstructure Evolution and Strengthening Mechanism of Dual-Phase Mg–8.3Li–3.1Al–1.09Si Alloys during Warm Rolling
In this study, the rolling process of the warm-rolled duplex-phase Mg–8.3Li–3.1Al–1.09Si alloy and the strengthening mechanism of as-rolled Mg–Li alloy were investigated. The highest ultimate tensile strength (UTS, 323.66 ± 19.89 MPa) could be obtained using a three-pass rolling process with a 30% thickness reduction for each pass at 553 K. The strength of the as-rolled LAS831 alloy is determined by a combination of second-phase strengthening, grain refinement strengthening, dislocation strengthening, and load-transfer reinforcement. Of these factors, dislocation strengthening, which is caused by strain hardening of the α-Mg phase, can produce a good strengthening effect but also cause a decrease in plasticity. The Mg2Si phase is broken up into particles or strips during the rolling process. After three passes, the AlLi particles were transformed into an AlLi phase, and the Mg2Si particles and nanosized AlLi particles strengthened the second phase to form a hard phase. The average size of the DRXed β-Li grains decreased with each successive rolling pass, and the average size of recrystallized grains in the three-pass-rolled LAS831 alloy became as low as 0.27 μm. The interface between the strip-like Mg2Si phase and the α-Mg phase is characterized by semicoherent bonding, which can promote the transfer of tensile and shear forces from the matrix to the strip-like Mg2Si phase, thereby improving the strength of the matrix and thus strengthening the LAS831 alloy.
Open AccessMicrostructure Evolution and Strengthening Mechanism of Dual-Phase Mg–8.3Li–3.1Al–1.09Si Alloys during Warm Rolling
In this study, the rolling process of the warm-rolled duplex-phase Mg–8.3Li–3.1Al–1.09Si alloy and the strengthening mechanism of as-rolled Mg–Li alloy were investigated. The highest ultimate tensile strength (UTS, 323.66 ± 19.89 MPa) could be obtained using a three-pass rolling process with a 30% thickness reduction for each pass at 553 K. The strength of the as-rolled LAS831 alloy is determined by a combination of second-phase strengthening, grain refinement strengthening, dislocation strengthening, and load-transfer reinforcement. Of these factors, dislocation strengthening, which is caused by strain hardening of the α-Mg phase, can produce a good strengthening effect but also cause a decrease in plasticity. The Mg2Si phase is broken up into particles or strips during the rolling process. After three passes, the AlLi particles were transformed into an AlLi phase, and the Mg2Si particles and nanosized AlLi particles strengthened the second phase to form a hard phase. The average size of the DRXed β-Li grains decreased with each successive rolling pass, and the average size of recrystallized grains in the three-pass-rolled LAS831 alloy became as low as 0.27 μm. The interface between the strip-like Mg2Si phase and the α-Mg phase is characterized by semicoherent bonding, which can promote the transfer of tensile and shear forces from the matrix to the strip-like Mg2Si phase, thereby improving the strength of the matrix and thus strengthening the LAS831 alloy.
- Open Access
- 14 December 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (24) , 4446
Strengthening Ni-Coated CNT/Mg Composites by Optimizing the CNT Content
The dispersion of carbon nanotubes (CNTs) is the bottleneck in CNT-reinforced metal matrix composites. In this work, CNT/Mg composites were prepared by grinding Mg powder and then dispersing CNTs via ball milling and hot pressing. The uniform distribution of Ni-coated CNTs in the matrix was achieved by optimizing the content of CNTs. Scanning electron microscope, high-resolution transmission electron microscopy and X-ray diffraction, optical microscopy, and compression tests were employed. With the CNT content being less than 1%, the CNTs can be evenly distributed in CNT/Mg composites, resulting in a sharp increase in strength. However, with the higher CNT content, the CNTs gradually cluster, leading decreased fracture strain and strength. Furthermore, the coated Ni in the CNTs reacts with the magnesium matrix and completely transforms into Mg2Ni, significantly enhancing the interface bonding. This strong interface bonding and the diffusely distributed Mg2Ni in the matrix significantly strengthen the CNT/Mg composite.
- 14 December 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (24) , 4446
Open AccessStrengthening Ni-Coated CNT/Mg Composites by Optimizing the CNT Content
The dispersion of carbon nanotubes (CNTs) is the bottleneck in CNT-reinforced metal matrix composites. In this work, CNT/Mg composites were prepared by grinding Mg powder and then dispersing CNTs via ball milling and hot pressing. The uniform distribution of Ni-coated CNTs in the matrix was achieved by optimizing the content of CNTs. Scanning electron microscope, high-resolution transmission electron microscopy and X-ray diffraction, optical microscopy, and compression tests were employed. With the CNT content being less than 1%, the CNTs can be evenly distributed in CNT/Mg composites, resulting in a sharp increase in strength. However, with the higher CNT content, the CNTs gradually cluster, leading decreased fracture strain and strength. Furthermore, the coated Ni in the CNTs reacts with the magnesium matrix and completely transforms into Mg2Ni, significantly enhancing the interface bonding. This strong interface bonding and the diffusely distributed Mg2Ni in the matrix significantly strengthen the CNT/Mg composite.
- Open Access
- 1 December 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (23) , 4277
Strengthening and Toughening CNTs/Mg Composites by OpTimizing the Grinding Time of Magnesium Powder
In this paper, CNT/Mg composites with high compressive properties were prepared by using Ni-plated CNT and pure magnesium powder as raw materials through the grinding of magnesium powder, ball-milling mixing and hot-pressing sintering. The effect of grinding time for finer magnesium powder on the microstructure and properties of the final composites was studied mainly by SEM, XRD, HRTEM and compression tests. The results show that with the prolongation of milling time, the magnesium particle size decreases gradually and the CNT dispersion becomes more uniform. Moreover, the nickel layer on the surface of CNT reacts with highly active broken magnesium powder in the sintering process to generate MgNi2 intermediate alloy, which significantly improves interface bonding. The strength and fracture strain of composites are significantly increased by the combined action of the uniform distribution of CNTs and strong interface bonding from the MgNi2 phase. The compressive strength, yield strength and fracture strain of the composites, prepared with a 60 h grinding of magnesium powder, reached 268%, 272% and 279% of those in composites without the grinding of magnesium powder.
- 1 December 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (23) , 4277
Open AccessStrengthening and Toughening CNTs/Mg Composites by OpTimizing the Grinding Time of Magnesium Powder
In this paper, CNT/Mg composites with high compressive properties were prepared by using Ni-plated CNT and pure magnesium powder as raw materials through the grinding of magnesium powder, ball-milling mixing and hot-pressing sintering. The effect of grinding time for finer magnesium powder on the microstructure and properties of the final composites was studied mainly by SEM, XRD, HRTEM and compression tests. The results show that with the prolongation of milling time, the magnesium particle size decreases gradually and the CNT dispersion becomes more uniform. Moreover, the nickel layer on the surface of CNT reacts with highly active broken magnesium powder in the sintering process to generate MgNi2 intermediate alloy, which significantly improves interface bonding. The strength and fracture strain of composites are significantly increased by the combined action of the uniform distribution of CNTs and strong interface bonding from the MgNi2 phase. The compressive strength, yield strength and fracture strain of the composites, prepared with a 60 h grinding of magnesium powder, reached 268%, 272% and 279% of those in composites without the grinding of magnesium powder.