Feibin Chen
Research Subjects
Feibin Chen has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Jiefeng Hu
Federation University
2 shared publications - Yong Li
School of Electrical Engineering, Southwest Jiaotong University, Chengdu, China
2 shared publications - Zhengyou He
School of Electrical Engineering, Southwest Jiaotong University, Chengdu, China
2 shared publications - Ruikun Mai
Tongji University
1 shared publication - Shunpan Liu
Key Laboratory of Magnetic Suspension Technology and Maglev Vehicle, Ministry of Education, School of Electrical Engineering, Southwest Jiaotong University, Chengdu, China
1 shared publication Tianren Lin
1 shared publication
Latest Publications
- 30 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Informatics
- Vol. 15 (9) , 5244-5256
A New Coil Structure and Its Optimization Design With Constant Output Voltage and Constant Output Current for Electric Vehicle Dynamic Wireless Charging
Dynamic wireless power transfer is a promising solution to address electric vehicle range anxiety and to reduce the ca-pacity and the cost of the on-board batteries. In the traditional DWPT system, the mutual inductances among transmitters make the design of compensation networks very complex. Besides, the power null phenomenon and the power pulsation phenomenon cause a fluctuating DC output voltage or current on the receiver side. To address these issues, this paper proposes a new magnetic coupler. Unipolar and bipolar coils are laid alternately to form segmented transmitters, which are turned ON or OFF according to the position of the overhead receiver coil. LCC compensations, whose inputs are connected in parallel to a common inverter for cost reduction, are adopted. At the receiver side, unipolar and bipolar coils are overlapped in the same plate in order to effec-tively smooth out the mutual inductance variations and hence, reduce the output voltage or current fluctuations. Also, a con-figurable resonant circuit is designed on the receiver side to achieve constant voltage (CV) charging and constant current (CC) charging. Moreover, an optimization design by using Fi-nite-element analysis software Maxwell is developed to choose the best turns of the receiver coil to further improve the output quality. A laboratory prototype with 4-A charging current and 96-V charging voltage, using 85kHz operation frequency, is con-structed to verify the proposed DWPT system. The experimental results show that constant output voltage and current can be achieved within 2% fluctuation, and the overall efficiency is 90.37%.
- 30 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Informatics
- Vol. 15 (9) , 5244-5256
A New Coil Structure and Its Optimization Design With Constant Output Voltage and Constant Output Current for Electric Vehicle Dynamic Wireless Charging
Dynamic wireless power transfer is a promising solution to address electric vehicle range anxiety and to reduce the ca-pacity and the cost of the on-board batteries. In the traditional DWPT system, the mutual inductances among transmitters make the design of compensation networks very complex. Besides, the power null phenomenon and the power pulsation phenomenon cause a fluctuating DC output voltage or current on the receiver side. To address these issues, this paper proposes a new magnetic coupler. Unipolar and bipolar coils are laid alternately to form segmented transmitters, which are turned ON or OFF according to the position of the overhead receiver coil. LCC compensations, whose inputs are connected in parallel to a common inverter for cost reduction, are adopted. At the receiver side, unipolar and bipolar coils are overlapped in the same plate in order to effec-tively smooth out the mutual inductance variations and hence, reduce the output voltage or current fluctuations. Also, a con-figurable resonant circuit is designed on the receiver side to achieve constant voltage (CV) charging and constant current (CC) charging. Moreover, an optimization design by using Fi-nite-element analysis software Maxwell is developed to choose the best turns of the receiver coil to further improve the output quality. A laboratory prototype with 4-A charging current and 96-V charging voltage, using 85kHz operation frequency, is con-structed to verify the proposed DWPT system. The experimental results show that constant output voltage and current can be achieved within 2% fluctuation, and the overall efficiency is 90.37%.
- 6 March 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 33 (10) , 8226-8230
A New-Variable-Coil-Structure-Based IPT System With Load-Independent Constant Output Current or Voltage for Charging Electric Bicycles
This letter presents a inductive power transfer (IPT) system based on a new variable coil structure to achieve load-independent constant current (CC) and constant voltage (CV) outputs for charging electric bicycles (EBs), without involving complex control strategies. The new variable coil structure consists of three-layer coils, i.e., two bipolar coils and one unipolar coil, on the transmitter side and one unipolar coil on the receiver side. The compact and portable receiver with series compensation is installed in the EB, while two switches on the transmitter side at the power charging station are utilized to re-configure the transmitter coil structure to select the charging mode, i.e., CC mode or CV mode. The proposed system can achieve zero phase angle (ZPA) operation, fixed operating frequency and zero voltage switching (ZVS), which will lower the power rating of power switches and improve the efficiency. A laboratory prototype is built to verify the feasibility of the proposed method.
- 6 March 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 33 (10) , 8226-8230
A New-Variable-Coil-Structure-Based IPT System With Load-Independent Constant Output Current or Voltage for Charging Electric Bicycles
This letter presents a inductive power transfer (IPT) system based on a new variable coil structure to achieve load-independent constant current (CC) and constant voltage (CV) outputs for charging electric bicycles (EBs), without involving complex control strategies. The new variable coil structure consists of three-layer coils, i.e., two bipolar coils and one unipolar coil, on the transmitter side and one unipolar coil on the receiver side. The compact and portable receiver with series compensation is installed in the EB, while two switches on the transmitter side at the power charging station are utilized to re-configure the transmitter coil structure to select the charging mode, i.e., CC mode or CV mode. The proposed system can achieve zero phase angle (ZPA) operation, fixed operating frequency and zero voltage switching (ZVS), which will lower the power rating of power switches and improve the efficiency. A laboratory prototype is built to verify the feasibility of the proposed method.