Jiande Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jiande Wang has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Daohai Qu
Hunan University State Key Laboratory of Advanced design and manufacturing for vehicle body, Changsha, Hunan China
1 shared publication - Feitie Zhang
State Key Laboratory of Advanced Design and Manufacture for Vehicle Body, Hunan University, Changsha, 410082, China
1 shared publication Quan Li
Engineering Research Centre of Automotive Electronics and Control Technology, Ministry of Education, Hunan University, Changsha 410082, China
1 shared publication- Yunfeng Liu
State Key Laboratory of Advanced Design and Manufacturing Technology for Vehicle, Hunan University, Changsha, China
1 shared publication Yunshan Zhou
Engineering Research Centre of Automotive Electronics and Control Technology, Ministry of Education, Hunan University, Changsha 410082, China
1 shared publication- Yunshan Zhou
State Key Laboratory of Advanced Design and Manufacture for Vehicle Body, Hunan University, Changsha, 410082, China
1 shared publication
Latest Publications
- 3 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 67 (11) , 10398-10410
Hydraulic System Control for a Hybrid Continuously Variable Transmission Based on an Electric Oil Pump
An electric oil pump (EOP) for the hydraulic system of a continuously variable transmission (CVT)-based hybrid electric vehicle is developed, by considering the arrangement of structures and the realization of electric drive mode (EDM). The basic parameters required for the EOP motor are obtained by analyzing the flow rate and pressure of CVT. Then, the EOP motor is designed and developed. Current-pressure characteristics of different solenoid valves are measured and analyzed for designing the CVT speed ratio controller. The speed ratio controller, pressure controller, and EOP control strategy are analyzed in detail with the use of EOP as the power source of the hydraulic system only. The performances of the speed ratio controller and the EOP control strategy are verified on a test bench. Experimental results show that the steady-state error of the speed ratio controller is minimal, and the response time of speed ratio from 0.7 to 1.4 can be shortened approximately 0.49 s to 1.40 s by increasing the EOP speed from 1000 rpm to 2500 rpm. The actual EOP speed can also be adjusted by the demand of system flow to save the maximum amount of energy.
- 3 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 67 (11) , 10398-10410
Hydraulic System Control for a Hybrid Continuously Variable Transmission Based on an Electric Oil Pump
An electric oil pump (EOP) for the hydraulic system of a continuously variable transmission (CVT)-based hybrid electric vehicle is developed, by considering the arrangement of structures and the realization of electric drive mode (EDM). The basic parameters required for the EOP motor are obtained by analyzing the flow rate and pressure of CVT. Then, the EOP motor is designed and developed. Current-pressure characteristics of different solenoid valves are measured and analyzed for designing the CVT speed ratio controller. The speed ratio controller, pressure controller, and EOP control strategy are analyzed in detail with the use of EOP as the power source of the hydraulic system only. The performances of the speed ratio controller and the EOP control strategy are verified on a test bench. Experimental results show that the steady-state error of the speed ratio controller is minimal, and the response time of speed ratio from 0.7 to 1.4 can be shortened approximately 0.49 s to 1.40 s by increasing the EOP speed from 1000 rpm to 2500 rpm. The actual EOP speed can also be adjusted by the demand of system flow to save the maximum amount of energy.
- Open Access
- 2 November 2014
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 7 (1)
Research on Fault Diagnostic System in CVT Based on UDS
A communication model of diagnostic network and implementation of unified diagnostic services (UDS) based on controller area network (CAN) bus are presented in this paper, and fault diagnostic function of transmission control unit (TCU), USB- (universal serial bus-) CAN hardware and software modules, and fault diagnostic software based on personal computer (PC) are designed. Model diagnostic method is applied on ratio control, and fault diagnostic system is tested in vehicle.
- 2 November 2014
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 7 (1)
Open AccessResearch on Fault Diagnostic System in CVT Based on UDS
A communication model of diagnostic network and implementation of unified diagnostic services (UDS) based on controller area network (CAN) bus are presented in this paper, and fault diagnostic function of transmission control unit (TCU), USB- (universal serial bus-) CAN hardware and software modules, and fault diagnostic software based on personal computer (PC) are designed. Model diagnostic method is applied on ratio control, and fault diagnostic system is tested in vehicle.