Aida Aberra
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Aida Aberra has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Sohmyung Ha
New York University Abu Dhabi
2 shared publications - Soon-Jae Kweon
School of Information, Communications and Electronic Engineering, The Catholic University of Korea, Bucheon-si, Gyeonggi-do, Republic of Korea
2 shared publications - Minkyu Je
Korea Advanced Institute of Science and Technology (KAIST)
1 shared publication - Muhammad Abrar Akram
Tampere University
1 shared publication - Song-I Cheon
School of Electrical Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon, South Korea
1 shared publication
Latest Publications
- 9 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 19 (5) , 993-1004
An Ultra-Low-Power Amplifier-Less Potentiostat Design Based on Digital Regulation Loop
This paper presents a new potentiostat circuit architecture for interfaces with amperometric electrochemical biosensors. The proposed architecture, which is based on a digital low-dropout regulator (DLDO) structure, successfully eliminates the need for transimpedance amplifier (TIA), control amplifier, and other passive elements unlike other typical potentiostat topologies. It can regulate the required electrode voltages and measure the sensor currents ( ISENSE ) at the same time by using a simple implementation with clocked comparators, digital loop filters, and current-steering DACs. Three different configurations of the proposed potentiostat are discussed including single-side regulated (SSR) potentiostat, dual-side regulated (DSR) potentiostat, and differential sensing DSR potentiostat with a background working electrode. These proposed potentiostats were designed and fabricated in a 180 nm CMOS process, occupying an active silicon areas of 0.0645 mm 2 , 0.1653 mm 2 , and 0.266 mm 2 , respectively. Validation results demonstrate that the proposed potentiostats operate on a wide sampling frequency range from 100 Hz to 100 MHz and supply voltage range from 1 V to 1.8 V. The proposed DSR potentiostat achieves a minimal power consumption of 3.7 nW over the entire dynamic range of 129.5 dB.
- 9 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 19 (5) , 993-1004
An Ultra-Low-Power Amplifier-Less Potentiostat Design Based on Digital Regulation Loop
This paper presents a new potentiostat circuit architecture for interfaces with amperometric electrochemical biosensors. The proposed architecture, which is based on a digital low-dropout regulator (DLDO) structure, successfully eliminates the need for transimpedance amplifier (TIA), control amplifier, and other passive elements unlike other typical potentiostat topologies. It can regulate the required electrode voltages and measure the sensor currents ( ISENSE ) at the same time by using a simple implementation with clocked comparators, digital loop filters, and current-steering DACs. Three different configurations of the proposed potentiostat are discussed including single-side regulated (SSR) potentiostat, dual-side regulated (DSR) potentiostat, and differential sensing DSR potentiostat with a background working electrode. These proposed potentiostats were designed and fabricated in a 180 nm CMOS process, occupying an active silicon areas of 0.0645 mm 2 , 0.1653 mm 2 , and 0.266 mm 2 , respectively. Validation results demonstrate that the proposed potentiostats operate on a wide sampling frequency range from 100 Hz to 100 MHz and supply voltage range from 1 V to 1.8 V. The proposed DSR potentiostat achieves a minimal power consumption of 3.7 nW over the entire dynamic range of 129.5 dB.
- 1 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 72 (00189456) , 1-11
Optimal Parameter Design of DAC-Based Sinusoidal Signal Generators for Electrical Impedance Spectroscopy
This paper provides parameter optimization processes of sinusoidal signal generators (SSGs) based on a digital-to-analog converter (DAC) for electrical impedance spectroscopy (EIS) applications. The SSG, which is the most power-hungry building block in EIS systems, generates a sinusoidal signal by using a DAC. To achieve high accuracy for the overall EIS system, high linearity is required for the sinusoidal signal. Thus, the SSG’s DAC is typically operated with a high oversampling ratio (OSR) and a large number of quantization levels ( LDAC ) at the expense of increased power consumption, large area, and high complexity. For efficient use of the power and area in the SSG, it is necessary to optimize the OSR, LDAC , and the order of the low-pass filter ( NLPF ). In this paper, optimal design parameters of SSGs, which can achieve highly accurate EIS systems with low complexity, are presented. First, the minimum OSR and NLPF for lowering the magnitude error to less than 0.1% are presented. Then, optimal quantization levels of finite-resolution DACs are found for sufficient accuracy and harmonic tones. In addition, the accuracy and harmonics of odd-number OSR cases are analyzed and compared with even-number OSR cases. According to the results, it is possible to design an SSG that only differs from the ideal sinusoidal signal by approximately 0.1% by using OSR ≤ 32, NLPF ≤ 2, and LDAC ≤ 256.
- 1 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 72 (00189456) , 1-11
Optimal Parameter Design of DAC-Based Sinusoidal Signal Generators for Electrical Impedance Spectroscopy
This paper provides parameter optimization processes of sinusoidal signal generators (SSGs) based on a digital-to-analog converter (DAC) for electrical impedance spectroscopy (EIS) applications. The SSG, which is the most power-hungry building block in EIS systems, generates a sinusoidal signal by using a DAC. To achieve high accuracy for the overall EIS system, high linearity is required for the sinusoidal signal. Thus, the SSG’s DAC is typically operated with a high oversampling ratio (OSR) and a large number of quantization levels ( LDAC ) at the expense of increased power consumption, large area, and high complexity. For efficient use of the power and area in the SSG, it is necessary to optimize the OSR, LDAC , and the order of the low-pass filter ( NLPF ). In this paper, optimal design parameters of SSGs, which can achieve highly accurate EIS systems with low complexity, are presented. First, the minimum OSR and NLPF for lowering the magnitude error to less than 0.1% are presented. Then, optimal quantization levels of finite-resolution DACs are found for sufficient accuracy and harmonic tones. In addition, the accuracy and harmonics of odd-number OSR cases are analyzed and compared with even-number OSR cases. According to the results, it is possible to design an SSG that only differs from the ideal sinusoidal signal by approximately 0.1% by using OSR ≤ 32, NLPF ≤ 2, and LDAC ≤ 256.